He||hammer

iTrader: (8)

Waiting since 09-02-2006 and 35 pages later

Chamberlin

iTrader: (1)

you want to be waiting to get your money back too? Pics of what? if you want to know why we are waiting, scan back a couple of pages.

1stgen8

iTrader: (1)

Sorry you guys lost your money but this proved to me that my gut feeling was right. I almost order these things.

Nopstnz8

iTrader: (6)

Good thing I decided not to order anything from this guy. I almost ordered a ton of stuff from him but changed my mind. It probably would have been all crap anyway. If he doesn't give you guys your money back soon, you should report him.

Mugatu

iTrader: (1)

well i FINALLY got my money sent back to me. it only took me spreading the word over at www.rx7club.com to get his attention.

if anyone else wants their money back, you better make a stink.

fd3s777

iTrader: (2)

anyone wants refund email me at jay@evo-r.net I will take care of this. I was busy for SEMA for the pass couple weeks. Mugatu not cool at all... so sad =(

Mugatu

iTrader: (1)

"not cool" dude? this has been an ongoing problem since september 25th. you CANNOT blame SEMA for your lack of communication for that long. We depended on you to keep us in the loop about this product and you have done nothing of the sort. I wanted to give you the benefit of the doubt, but when you let something like this go this long with absolutely no solution in sight, a refund was in order. it's still a shame that I'm still out the $75 it cost me to paint them, since that money is completely wasted now.

I sent PMs and emails to you, but only heard from you when I posted on the other forum. You said you are still at SEMA, but if you're checking your emails while you're there, what's your excuse for waiting so long?

fd3s777

iTrader: (2)

No excuse, but previous waiting time was for a new version which suppose to fit better. But factory never deliver. So I decide to refund you

Chamberlin

iTrader: (1)

I will wait for next revision, I didn't think there was going to be one. So I will not ask for the money back at this time. Yes, it does hurt to loose the painting money, but maybe I could get my replacement version painted at a discount? It would be nice to not have to bug my painter again for such a small job. Let me know what you think.

-C

fd3s777

iTrader: (2)

I got a set painted in Ti gray. I will test fit this weeken.

Chamberlin

iTrader: (1)

Sounds good, let us know how it goes....

Nemesis8

iTrader: (3)

^^ Good news Jay - keep us posted

fd3s777

iTrader: (2)

just got one installed myself yesterday

fd3s777

iTrader: (2)

Advise! Do not use ziptie. It is just too hard and there are no holding point on the top or bottom part of the vents. What we use is 3M Butyl Rubber tape. Apply this over almost edge of the inner surface of the fender vent hole. Put about 3 layers on the 2 middle bars. "DO NOT!" put too close to the outter edge. Cuz once you push on the vents the butyl will be pushed out and you will have hard time cleaning those TAR out. Once on use heat gun or blow dryer. Heat the vents ahd push it in till it is in shape and fully in. This should stay on for good. Easy to remove and reasy to put on. It will not fall out during driving.

Chamberlin

iTrader: (1)

Wait, I thought you were designing a whole new vent that worked? I already tried the double sided tape thing with mine (got some pro stuff from my painter), and since the shape is too far off from actual, after a while it either pulls away or won't stay lined up right, and the double sided foam can be seen easily unless you do it perfect.....................

So you are not making new designed vents then? That is all I want to know.

fd3s777

iTrader: (2)

double side tape will not do. Cuz it is too thin to hold the whole surface of the vents. This is why I use 3M Butyl Rubber which is very thick. Can shape the curve that is not perfect covered.

Mugatu

iTrader: (1)

wow if that is the solution, i am glad i asked for my money back. from those photos you can still see the 3M tape. eyelids attached by tape is one thing, but vents should not be.

these need to be re-engineered, not makeshift fixed.

Chamberlin

iTrader: (1)

Yea, I was under the impression that these were being re-engineered, not re-rigged.

rx8spiritR

it's been too long
if the carbon fiber one coming soon????

Mugatu

iTrader: (1)

yes carbon fiber ones are coming - they attach with duct tape and chewing gum.

laythor

Watching this thread devolve over the months has been like watching a train wreck in slo motion.

Wing5

^^^Minus the suspense and cool factor. But things gone utterly wrong: yes.

shakeyourbrakes

iTrader: (4)

Hey Jay since I cant get you at all through your phone number, your "24 hour" AIM screename, your email or PM's..ill try here... let me know whats up with my order you have 119 dollars of mine for the vents and I havnt heard a word back!!!!!!!!!!!!Apparently you post on this thread though so you def log in!

laythor

http://uk.youtube.com/watch?v=EOuwyf...eature=related

BigRed

he^