how to pre-load springs
#1
Registered User
Thread Starter
Join Date: Mar 2008
Location: Fairfax/Richmond, VA
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
how to pre-load springs
I was just wondering what the best way to preload springs are. I installed vogtland springs and i barely can tell that it is lowered. I was thinking i have to preload them
#2
Administrator
iTrader: (7)
Never fear, Jedi is here!
All you need to do is loosen the following bolts while it's on the ground, let it sit to 'load' the weight on the suspension and then tighten everything back up.
All you need to do is loosen the following bolts while it's on the ground, let it sit to 'load' the weight on the suspension and then tighten everything back up.
#7
Zoom-Freakin'-Zoom
iTrader: (5)
you have to also loosen the bolt on the other side of the a arm..
it can be done with the car on the ground. just turn the wheel to one side.
i find it helpful to drive around the block. speed bumps help. then tighten them up.. once again. the two bolts on the lower a arm..
beers
it can be done with the car on the ground. just turn the wheel to one side.
i find it helpful to drive around the block. speed bumps help. then tighten them up.. once again. the two bolts on the lower a arm..
beers
#9
Registered
iTrader: (1)
Join Date: May 2006
Location: Carolina Beach, NC
Posts: 1,934
Likes: 0
Received 0 Likes
on
0 Posts
The only way I know of to preload the rears is to use a spring clamp and compress the springs as much as you can then, slide on the upper spring perch and tighten down the nut as much as possible. There are no external ways to adjust the rears.
#11
Administrator
iTrader: (7)
Here's your answer:
you have to also loosen the bolt on the other side of the a arm..
it can be done with the car on the ground. just turn the wheel to one side.
i find it helpful to drive around the block. speed bumps help. then tighten them up.. once again. the two bolts on the lower a arm..
beers
it can be done with the car on the ground. just turn the wheel to one side.
i find it helpful to drive around the block. speed bumps help. then tighten them up.. once again. the two bolts on the lower a arm..
beers
#16
Registered
iTrader: (25)
Even the people who think they know how, don't.
It has to be on jackstands with all four wheels up in the air.
you have to have at least one swaybar endlink end taken loose on each swaybar.
Once this is done you can jack any corner up into compression easily and then retighten the suspension arm bolts
it can be done on the ground rather than on jackstands, but the suspension needs to be settled first which means driving it around some withe everything loose and it's more of a PITA to reach in and around to tighten everything. Using the jackstand method above allows you to compress the suspension to whatever position you want, including almost full compression, before retightening it easily.
.
It has to be on jackstands with all four wheels up in the air.
you have to have at least one swaybar endlink end taken loose on each swaybar.
Once this is done you can jack any corner up into compression easily and then retighten the suspension arm bolts
it can be done on the ground rather than on jackstands, but the suspension needs to be settled first which means driving it around some withe everything loose and it's more of a PITA to reach in and around to tighten everything. Using the jackstand method above allows you to compress the suspension to whatever position you want, including almost full compression, before retightening it easily.
.
Last edited by TeamRX8; 11-18-2009 at 08:21 AM.
#21
Out of NYC
iTrader: (1)
Even the people who think they know how, don't.
It has to be on jackstands with all four wheels up in the air.
you have to have at least one swaybar endlink end taken loose on each swaybar.
Once this is done you can jack any corner up into compression easily and then retighten the suspension arm bolts
It has to be on jackstands with all four wheels up in the air.
you have to have at least one swaybar endlink end taken loose on each swaybar.
Once this is done you can jack any corner up into compression easily and then retighten the suspension arm bolts
Guess I did it right the whole time
#22
Registered
iTrader: (1)
Join Date: Aug 2009
Location: Milford, MA
Posts: 322
Likes: 0
Received 0 Likes
on
0 Posts
I guess that makes sense but it just looks so weird. For a daily driver, do you think there would be a noticeable difference in handling by preloading the front stock springs if that's even possible?
#24
Drummond Built
iTrader: (6)
hmm I'm not sure if I did it correctly but I took a jack while my car was on stands, sways still connected and tight, and for the rears: jacked up the car under the rotor somewhere, I forget exactly and then tighted the bolts down.
for the fronts I just loosened the front control arms and jumped on the car a little to settle them, granted the springs have had like 10K on them so they were already settled.
But after reading this thread I'm wondering if I did this all correctly... I'll post pics of my car from the side and see if yall think it looks correct
for the fronts I just loosened the front control arms and jumped on the car a little to settle them, granted the springs have had like 10K on them so they were already settled.
But after reading this thread I'm wondering if I did this all correctly... I'll post pics of my car from the side and see if yall think it looks correct
#25
SARX Legend
iTrader: (46)
That good info team posted, I have always done it the other way but since the car is on stands anyway, why not. I had another local guy here call me all upset because he was in a rush to get them on and did them himself and was pissed because he was not lower. I asked him if he preloaded them and he was like, "preload, what's that?"
I told him what to do and he was a happy camper afterward.
I told him what to do and he was a happy camper afterward.