Help...lol...Red Light???
#78
Dodging those Corollas
iTrader: (2)
Friday evening, June 25, 6pm
GO Langstaff station PARKING LOT located at Red Maple Dr. and Hwy 7. There is a convenient Tim Hortons located right there...
Tools I will be bringing:
1) screw driver set
2) hex set
3) set of pliers
4) digital multimeter
5) Scanguage II
We will be driving around with your hood semi-closed so that the wires could be brought back through the passenger side window.
Leesha, you will need to bring:
1) Booster cables (using them as extension cords for the meter leads)
We will be monitoring the voltage 2 ways:
A) Scanguage II plugged into OBD-II port showing Voltage. I will require NEO to sit in the back and monitor that one.
B) Hardwire voltage check on digital multimeter connected at various points:
i) On battery terminals
ii) On generator output terminals
As you drive, as soon as the light comes on, we should be able to get some results and conclusions based on what the Scangauge and the digital multimeter (DMM) says.
If this is a vibration issue, then perhaps it could also be simulated at a lower speed... you mention it happens around your cruise speed of 130 km/h. Assuming you are in 6th gear, this is about 4200 rpm. Perhaps if we drive around at 4200 rpm, a certain frequency range is causing some sort of natural vibration about the way your wires are arranged, could be causing that too...
GO Langstaff station PARKING LOT located at Red Maple Dr. and Hwy 7. There is a convenient Tim Hortons located right there...
Tools I will be bringing:
1) screw driver set
2) hex set
3) set of pliers
4) digital multimeter
5) Scanguage II
We will be driving around with your hood semi-closed so that the wires could be brought back through the passenger side window.
Leesha, you will need to bring:
1) Booster cables (using them as extension cords for the meter leads)
We will be monitoring the voltage 2 ways:
A) Scanguage II plugged into OBD-II port showing Voltage. I will require NEO to sit in the back and monitor that one.
B) Hardwire voltage check on digital multimeter connected at various points:
i) On battery terminals
ii) On generator output terminals
As you drive, as soon as the light comes on, we should be able to get some results and conclusions based on what the Scangauge and the digital multimeter (DMM) says.
If this is a vibration issue, then perhaps it could also be simulated at a lower speed... you mention it happens around your cruise speed of 130 km/h. Assuming you are in 6th gear, this is about 4200 rpm. Perhaps if we drive around at 4200 rpm, a certain frequency range is causing some sort of natural vibration about the way your wires are arranged, could be causing that too...
Last edited by Footman; 06-23-2010 at 08:41 PM.
#81
View at your own Risk :)
Thread Starter
Damn that is my mom's Bday...****! LoL...do you realize how long it would take me to get there on a Friday evening... Friday can't work... Pick another day...lol...I work on the weekend so after 5 is good.
#82
Registered User
#84
I am The One!
Sophia,
You've been hanging around your bro too long. lol
FYI, I do all my own work on my FD and Miata. I've gotten tired of paying the dealer do these "services" for huge dollars. :p
Leesha,
Of course I'm going to be there. That goes without saying.
But now we can't do Fri.
Footman,
What's plan B?
You've been hanging around your bro too long. lol
FYI, I do all my own work on my FD and Miata. I've gotten tired of paying the dealer do these "services" for huge dollars. :p
Leesha,
Of course I'm going to be there. That goes without saying.
But now we can't do Fri.
Footman,
What's plan B?
#86
View at your own Risk :)
Thread Starter
#87
View at your own Risk :)
Thread Starter
I work in burlington till 5pm. How bout you guyz meet me after work and we can go down by the beaches or behind my work building and work on it there????
#89
Registered User
#91
View at your own Risk :)
Thread Starter
Guyz the G summit folks are rolling in... Not sure if I'll be able to get to Toronto.
However I had an idea. Maybe Neo can bring Footman and Foot you can ride with me in my 8 back to T.O. and see the problem I'm having.
What do you guys think? This Saturday then I'll go party with my g/f.
However I had an idea. Maybe Neo can bring Footman and Foot you can ride with me in my 8 back to T.O. and see the problem I'm having.
What do you guys think? This Saturday then I'll go party with my g/f.
![Smilie](https://www.rx8club.com/images/smilies/smile.gif)
Last edited by Leesha; 06-24-2010 at 12:42 PM.
#96
My RX-8 purrs.....
LOL... I had some reading to do on this thread as I have not been on in a bit. Back in post #23 I mentioned that I had a similar problem last year with my MX-3. It turned out to be a worn pulley, which in turn was causing the belt to slip...which caused my light to flicker every so often. I ignored it and the little screech every once in a while. A few months later the light came on....stayed on...the radio died...then the car died. The belt actually slipped right off!
New pulley, new belt...good to go!
I'm not saying this is the problem, but maybe the belt is slipping every so often....hey what do I know...I only design blast furnaces for a living....
New pulley, new belt...good to go!
I'm not saying this is the problem, but maybe the belt is slipping every so often....hey what do I know...I only design blast furnaces for a living....
#98
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 12 Likes
on
9 Posts
^.............I mentioned that a while back. It is possible since it's only happening at pretty decent speeds. A belt might just be a little sloppy, or as you said............maybe a worn pulley?
Think Footman's got a plan.......and not that it would do any good in the case, but I have the electrical diagram if he needs it(just PM with E-mail addy). Check the damn plug on top of the alternator as well, it might be high resistive right there????
Intermittent problems are always tough to track down.
Think Footman's got a plan.......and not that it would do any good in the case, but I have the electrical diagram if he needs it(just PM with E-mail addy). Check the damn plug on top of the alternator as well, it might be high resistive right there????
Intermittent problems are always tough to track down.
![Banghead](https://www.rx8club.com/images/smilies/banghead.gif)
Last edited by Mazurfer; 06-24-2010 at 07:41 PM.
#99
View at your own Risk :)
Thread Starter
LMAO your right about that comment. It does sound dirty...lol...
"Boyz meet me down south... right by the lake then we can test my car out for vibrations."
![Yelrotflmao Vi](https://www.rx8club.com/images/smilies/yelrotflmao-vi.gif)
![Smilie](https://www.rx8club.com/images/smilies/smile.gif)
I like how this sounds better than the above statement. What do you think? Are you in or out...
![Yelrotflmao Vi](https://www.rx8club.com/images/smilies/yelrotflmao-vi.gif)
![Smilie](https://www.rx8club.com/images/smilies/smile.gif)
Hey Catty: How will I know if its the pully? Is it hard to figure out? Or the belt??
Last edited by Leesha; 06-24-2010 at 08:04 PM.
#100
My RX-8 purrs.....
![Whip](https://www.rx8club.com/images/smilies/whip.gif)
![Whip](https://www.rx8club.com/images/smilies/whip.gif)
Last edited by Cdn Cat; 06-24-2010 at 11:06 PM.