Quite a good review..
#1
Registered User
Thread Starter
Join Date: Apr 2003
Location: London, UK
Posts: 487
Likes: 0
Received 0 Likes
on
0 Posts
#2
Registered User
Join Date: May 2003
Location: Bristol
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
Has anyone noticed how every single review quotes the 0 - 60 as 6.4 secs. Do you think anyone has actually tested this with timing gear or are they all using the quoted Mazda figure.
I just find it strange because normally the cars mags do vary a few tenths of a second from the manafactureres figures and from other mags?
Nice review by the way obviously a rotar fan
I just find it strange because normally the cars mags do vary a few tenths of a second from the manafactureres figures and from other mags?
Nice review by the way obviously a rotar fan
![Smilie](https://www.rx8club.com/images/smilies/smile.gif)
#3
"With a red line just short of 10,000 rpm (there is a warning bleep to prevent over-revving, something that wrecks rotary engines very quickly)"
Tip of the day, dont go past the rev limiter...
Not a bad review at all, seems to like it.
Tip of the day, dont go past the rev limiter...
Not a bad review at all, seems to like it.
#4
Can't Re Member
Join Date: Apr 2003
Location: Leeds, UK
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
It's quite a good review, but I've seen it posted somewhere else on the forum.
As you guys appreciate though, it is hard to trawl through the whole forum seeing if it already exists, so keep up the good work.
STU
As you guys appreciate though, it is hard to trawl through the whole forum seeing if it already exists, so keep up the good work.
STU
#5
_________________
Join Date: Feb 2003
Location: Cambridge - UK
Posts: 1,384
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by RobDickinson
"With a red line just short of 10,000 rpm (there is a warning bleep to prevent over-revving, something that wrecks rotary engines very quickly)"
Tip of the day, dont go past the rev limiter...
Not a bad review at all, seems to like it.
"With a red line just short of 10,000 rpm (there is a warning bleep to prevent over-revving, something that wrecks rotary engines very quickly)"
Tip of the day, dont go past the rev limiter...
Not a bad review at all, seems to like it.
#9
_________________
Join Date: Feb 2003
Location: Cambridge - UK
Posts: 1,384
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by RobDickinson
I was trying sarcasm out :P
Anyhow, no throttle control can stop you downshifting from 6 to 2nd....
I was trying sarcasm out :P
Anyhow, no throttle control can stop you downshifting from 6 to 2nd....
![Wink](https://www.rx8club.com/images/smilies/wink.gif)
#11
Registered User
Join Date: May 2003
Location: Herts - UK
Posts: 350
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by copperband
Has anyone noticed how every single review quotes the 0 - 60 as 6.4 secs. Do you think anyone has actually tested this with timing gear or are they all using the quoted Mazda figure.
I just find it strange because normally the cars mags do vary a few tenths of a second from the manafactureres figures and from other mags?
Has anyone noticed how every single review quotes the 0 - 60 as 6.4 secs. Do you think anyone has actually tested this with timing gear or are they all using the quoted Mazda figure.
I just find it strange because normally the cars mags do vary a few tenths of a second from the manafactureres figures and from other mags?
#12
Registered User
Join Date: Apr 2003
Location: Worcestershire
Posts: 434
Likes: 0
Received 0 Likes
on
0 Posts
ChrisW, if these are pre-production cars, do you think Mazda would be under hand and supplied 250ps cars rather than than 231ps cars ? It would'nt be the first time a car manufacturer has handed over a more powerful car, to make it look good. Disappointingly, if they have, the 0-60 time should have been better.
After all that Mazda have done (or not done), I wouldn't put it past them.
AnilS.
After all that Mazda have done (or not done), I wouldn't put it past them.
AnilS.
Thread
Thread Starter
Forum
Replies
Last Post
Touge
Canada Forum
3
09-10-2015 08:07 AM
LMURailsplitter02
New Member Forum
1
09-06-2015 10:56 PM