RX8Club.com
Had hell figuring out a way to clear the ac line and bumper.
Had hell figuring out a way to clear the ac line and bumper.
0 2023/02/13 15:12:17
Knocked some dust off this thing. Still haven't decided what where going to do with it just yet.
Knocked some dust off this thing. Still haven't decided what where going to do with it just yet.
0 2023/02/13 15:12:08
0 2023/02/05 18:53:15
Got one line crimped and installed. Ordered the wrong compression fitting size for the other line unfortunately.
Got one line crimped and installed. Ordered the wrong compression fitting size for the other line unfortunately.
0 2023/02/05 18:52:50
It's a tight fit between the frame rails but managable
It's a tight fit between the frame rails but managable
0 2023/02/02 10:54:00
Fresh FAL 420's.
Fresh FAL 420's.
0 2023/02/02 10:53:49
Have to fab new mounts for everything since the Kotor moves everything several inches forward
Have to fab new mounts for everything since the Kotor moves everything several inches forward
0 2023/02/02 10:53:39
0 2023/02/02 10:53:26
Due to the higher water necks the usual swirl pot mod was needed.
Due to the higher water necks the usual swirl pot mod was needed.
0 2023/02/02 10:53:11
I'm no serious welder but it does the job and doesn't leak
I'm no serious welder but it does the job and doesn't leak
0 2023/02/02 10:53:01
0 2023/02/02 10:52:51
Old s13 setup with a single SPAL fan. Did the job
Old s13 setup with a single SPAL fan. Did the job
0 2023/02/02 10:52:37
Fittings mounted uncrimped. Everything fits well.
Fittings mounted uncrimped. Everything fits well.
0 2023/02/02 10:43:53
0 2023/02/02 10:43:35
First issue is the stud is too close so I can put a nut on it. Gonna remove the stud and just run a regular bolt
First issue is the stud is too close so I can put a nut on it. Gonna remove the stud and just run a regular bolt
0 2023/02/02 10:43:16
0 2023/02/02 10:43:05
Got these fittings from coldhose.com. The fittings on the right are compression fittings to adapt to the Mazda lines. I could have ran them in both ends and reused the Toyota compressor fittings but they where too bulky for my liking.
Got these fittings from coldhose.com. The fittings on the right are compression fittings to adapt to the Mazda lines. I could have ran them in both ends and reused the Toyota compressor fittings but they where too bulky for my liking.
0 2023/02/02 10:42:48
0 2023/02/02 10:22:18
Brake lights. Turn signals are orange and sequential.
Brake lights. Turn signals are orange and sequential.
0 2023/01/31 19:48:34
Up close. Running lights
Up close. Running lights
0 2023/01/31 19:47:32
My favorite mod has been these taillights by Valenti in Japan. They aren't cheap but if you've owned an s2 you know the OEM tails get water in them and fry. Replacement cost are basically the same as these. Also they designed them to fit either generation which was brilliant
My favorite mod has been these taillights by Valenti in Japan. They aren't cheap but if you've owned an s2 you know the OEM tails get water in them and fry. Replacement cost are basically the same as these. Also they designed them to fit either generation which was brilliant
0 2023/01/31 19:43:51
0 2023/01/31 19:38:10
Because of the s2 rear bumper hanging lower on the exhaust shrouds you have to run drop hangers to avoid the bumper touching the exhaust tips. I really think they could have designed this much better because there's a massive gap above the mufflers and the trunk floor. Also ground clearance isn't great
Because of the s2 rear bumper hanging lower on the exhaust shrouds you have to run drop hangers to avoid the bumper touching the exhaust tips. I really think they could have designed this much better because there's a massive gap above the mufflers and the trunk floor. Also ground clearance isn't great
0 2023/01/31 19:36:38
Here you can sorta see the hoop that bolts to the subframe to support the diff. I have a spare subframe and an 8.8 I plan to swap with the Keisler setup unless someone out there has a 3.9 FD ring gear they want to sell me
Here you can sorta see the hoop that bolts to the subframe to support the diff. I have a spare subframe and an 8.8 I plan to swap with the Keisler setup unless someone out there has a 3.9 FD ring gear they want to sell me
0 2023/01/31 19:34:11
Had to add a section of 3" oval tubing from downpipe to the catback in order to clear the floor/trans/x brace
Had to add a section of 3" oval tubing from downpipe to the catback in order to clear the floor/trans/x brace
0 2023/01/31 19:32:52
The turbo xs has these kinda Rickey burn blue tips but I kinda dig them even tho I'm actually not a fan of blue
The turbo xs has these kinda Rickey burn blue tips but I kinda dig them even tho I'm actually not a fan of blue
0 2023/01/31 19:31:57
0 2023/01/31 19:29:45
First time out the driveway under its own power back in 21
First time out the driveway under its own power back in 21
0 2023/01/31 19:28:27
0 2023/01/31 19:25:13
0 2023/01/31 17:40:19
Fc vert I'm restoring
Fc vert I'm restoring
0 2023/01/31 17:36:11
0 2023/01/31 17:33:43
0 2023/01/31 17:32:14
0 2023/01/31 17:26:02
18x10.5 +12 Rays Gramlights 245/45 square
18x10.5 +12 Rays Gramlights 245/45 square
0 2023/01/31 17:21:48
For those that might care I'm restoring a FC vert and a possibly 13b swapped Datsun 280
For those that might care I'm restoring a FC vert and a possibly 13b swapped Datsun 280
0 2023/01/26 16:19:25
0 2023/01/26 16:17:06
0 2023/01/26 16:17:00
0 2023/01/26 16:16:08