Offical New Rx8 LED Brake Light Group Buy
#129
HEADTURNER
Join Date: Jan 2007
Location: University of Missouri & STL
Posts: 1,100
Likes: 0
Received 0 Likes
on
0 Posts
juat got mine today and installed them tonight, if its nice tom i will post pics, but i do have to say they look SEXY with the Kenstyle rear bumper! Once again thanks for the GB saki
#131
fō'tə-jěn'
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Temple City, CA
Posts: 379
Likes: 0
Received 0 Likes
on
0 Posts
will be shipping out on Wednesday, sorry for the delay but they will be back to work on Wednesday.
Yours shipped out already, i will pm you again. Sorry for the delay.
get it, both will ship out on Wednesday
get it, will ship out on Wednesday. Sorry for the delay.
Yours shipped out already, i will pm you again. Sorry for the delay.
get it, both will ship out on Wednesday
get it, will ship out on Wednesday. Sorry for the delay.
#136
#139
#140
X e p i A
iTrader: (1)
Smoked lens or OEM without the mask. The LEDs are bright enough that you can see them through the mask and the light they put out isn't diffuse, they are individual dots of light. I just don't think it works well with the mask. The pics of the first setup look great though.
#143
I was trying to remove the trunk liner today but wasn't successful. I tried to pry the clips using butter knives; got them to loosen up but they wouldn't pop out.
I'd appreciate any pointers!
The LED's should arrive tomorrow and I have also purchased some smoke tints to overlay the tail lamps with. Will post pics after the install.
I'd appreciate any pointers!
The LED's should arrive tomorrow and I have also purchased some smoke tints to overlay the tail lamps with. Will post pics after the install.
#144
Registered Toker
iTrader: (2)
all of my clips you just had to unscrew using a Phillips...
you have to give them a pretty good yank
If they aren't the "screw" type, you have to loosen the smaller circle away from the outer circle using a flathead of some sort (exacto, small flathead screwdriver etc.)
you have to give them a pretty good yank
If they aren't the "screw" type, you have to loosen the smaller circle away from the outer circle using a flathead of some sort (exacto, small flathead screwdriver etc.)
Last edited by Ross_Dawg; 01-04-2009 at 10:15 PM.
#145
Finally a MT
iTrader: (11)
I was trying to remove the trunk liner today but wasn't successful. I tried to pry the clips using butter knives; got them to loosen up but they wouldn't pop out.
I'd appreciate any pointers!
The LED's should arrive tomorrow and I have also purchased some smoke tints to overlay the tail lamps with. Will post pics after the install.
I'd appreciate any pointers!
The LED's should arrive tomorrow and I have also purchased some smoke tints to overlay the tail lamps with. Will post pics after the install.
#146
Happy.... Thanks Saki.
Ok guys.
Just received mine this morning and installed it.
I had some probs with the rubber around the light.
It was new and very hard so the light as much as I tried to push it would not sit in right place.
So was I did I replaced the new rubber with the old one. And it worked.
BTW IT LOOKS AWESOME ON WHITE.
What do you think?
I'll try to take some pictures tonight.
Just received mine this morning and installed it.
I had some probs with the rubber around the light.
It was new and very hard so the light as much as I tried to push it would not sit in right place.
So was I did I replaced the new rubber with the old one. And it worked.
BTW IT LOOKS AWESOME ON WHITE.
What do you think?
I'll try to take some pictures tonight.