9krpmrx8

iTrader: (46)

So that is at the low end of the spec right?

shadycrew31

iTrader: (6)

Yes.. the minimum is 6.8 max is 8.5.

but for housings with chrome flake, porting, and no omp. This thing is kicking ***!

9krpmrx8

iTrader: (46)

Dude, you gotta get that OMP situation resolved.

shadycrew31

iTrader: (6)

Yea... It kind of on the bottom of the list, since premix seems to be doing a decent job.

shadycrew31

iTrader: (6)

And this is what I was talking about...

https://www.rx8club.com/rx-8-parts-s...-lines-235533/

http://www.nopistons.com/rotary-engi...p-lines-74312/

9krpmrx8

iTrader: (46)

I thought you ran out of premix?

9krpmrx8

iTrader: (46)

Looks good but I'd like to see how the route. SS lines do not do good rubbing against other stuff.

shadycrew31

iTrader: (6)

They should be fairly loose, I dont see where they would rub.

shadycrew31

iTrader: (6)

Yea I did for a little bit, I kept forgetting to pick it up at the store! I'm still running 1 oz per fillup, she loves it.

I'm only pulling in about 240g/s though, which isn't too bad but not like the 250-260 I was seeing.

9krpmrx8

iTrader: (46)

Well they have to come together on the front cover to run down to the OMP. Might be a non issue, but I have seen nitrous lines wear through over time, especially against aluminum or plastic.

shadycrew31

iTrader: (6)

yea, but they can be ran slightly differently if I remember correctly.

9krpmrx8

iTrader: (46)

I would love to see a set installed.

shadycrew31

iTrader: (6)

You will on some 09 housings in about 7 months...

9krpmrx8

iTrader: (46)

You going to put extra injectors in as well?

shadycrew31

iTrader: (6)

Yep... assuming I can find someone to make the lines for me the way I want.

And also assuming I don't blow and apex seal between now and then and can reuse everything but my housings.

hoss -05

iTrader: (4)

I bet taylor hose could custom make you exactly what you want.

9krpmrx8

iTrader: (46)

Yep, just need the measurements. Hydraulic supply actually specializes in custom SS brake lines as well.

shadycrew31

iTrader: (6)

Awesome...

I mean it would be easy enough to do it. I would just need a brass Y fitting, for the third injector.

I've put allot of thought into it.

9krpmrx8

iTrader: (46)

You think the oil would flow even to both injectors with a "Y" ?

shadycrew31

iTrader: (6)

Winning?

V-Band Adapter - GT25/GT28/GT307X-WG Series : atpturbo.com

9krpmrx8

iTrader: (46)

You making a new down pipe?

shadycrew31

iTrader: (6)

no, but whatever amount made it would be better than nothing.

9krpmrx8

iTrader: (46)

But what if it robbed oil from going to the side?

shadycrew31

iTrader: (6)

Not sure yet... Just trying to see how complicated I can make my build.

But a V-band would make like a million times easier removing the turbo in the future. plus I think it would flow better....

9krpmrx8

iTrader: (46)

It cost quite a bit to have a new down pipe fabricated with V bands on it. It would make life a lot easier though for removal.