astevens26

noooooo! how long has the process been and how many data submissions have you made? i guess i had my hopes too high for a simple pug and play when you have boost involved

MazdaManiac

iTrader: (3)

You ordered on the 8th. The 21st was a holiday. Your shipping date is TODAY.

That is not strictly true. Read the instructions.

RotaryMachineRx

iTrader: (1)

^ well 2-3 psi.... but definitely still doing easy driving

astevens26

thanks for the quick responce...

Blacknightz

wohooo !!! time to get some UPGRADES !

2k4_8

I believe even that isn't 100 %.... it's more about your individual afrs and if you experience any detonation than anything. Not to say you should hot rod it around.

2k4_8

Sorry, quoted wrong post and I'm on.my cell....will have to fix it later!

rubberduckie

I just got new leading spark plugs because mine where 'plugged' causing CAT issues, etc....

Anyways, they pulled the P0301 code for misfires, is this blocked by the AP as I did not see a CEL?

Secondly, and more importantly, I am only on 4.0.1 but how will the new plugs possibly effect my tune, and future tunes? Should I be fine running 4.0.1 still, or should I be concerned and look for anything with the AFRs?

Thanks.

Edit - Reading that anything that doesn't affect the AFR's need no re-tune, the AFR's are taken from the first O2 sensor in CAT are they not? Would having more 'burnt' fuel from the new plugs change the AFR? Perhaps I am just be overly cautious.

MazdaManiac

iTrader: (3)

PLEASE READ THE THREAD LOCATED HERE:

https://www.rx8club.com/mazdamaniac-183/attention-current-mazdamaniac-custom-calibration-customers-212845/#post3902655

longpath

iTrader: (1)

Has anyone run into an issue where they press the Ok button to start logging and the AccessPort locks up, so that it not only doesn't record the log; but doesn't do anything else either?

Blacknightz

Has happened to me before... Check ur connection from AP to OBD.. either one might have been lose... i changed mine to a new one and the problem is solved...

RotaryMachineRx

iTrader: (1)

I get it the odd time... just unplug the AP then plug it back in and after it reboots it usually works for me

CVale127

iTrader: (17)

Quick question guys.....I know the stock AP stage 1 maps clearly state that it should only bee used on "otherwise stock vehicles with a stock intake and stock or cat-back exhaust" because having mods such as a midpipe could make the car run too lean etc....which in turn can lead to engine damage. I downloaded the map once before while having an RB midpipe, full exhaust, and bhr kit and noticed a significant increase in accerlation and throttle response, but quickly uninstalled it after reading these warnings on the cobb website lol.

My question is....what if you use this map with a revi intake and bhr ignition kit. Do you think it would be harmful to the engine ?

laythor

avoid the stock cobb map like the plague, regardless of any mods

CVale127

iTrader: (17)

And the reason being...?

bse50

fixed

laythor

it has been shown to do less then desirable things to the tune of your car.

MazdaManiac

iTrader: (3)

You can run the Cobb Stage 1 calibration if you want to. It might even be relatively correct for the car.
However, it is typically way too lean and the timing is way too advanced and you will most likely experience detonation at some point.
The likelyhood that it has your MAF calibration right is slim to none.

And, most importantly - your butt is not a dyno. Simply loading the "stock-style" map probably would have felt faster to you.

CVale127

iTrader: (17)

Last time i checked this was a Cobb Accessport Discussion thread. Is it not ? Correct me if im wrong.

MazdaManiac

iTrader: (3)

I think what he was pointing out was that your point has already been discussed over and over and over again.

It is generally considered bad etiquette to walk into a discussion and demand that the participants provide you with a synopsis because you were too impatient to catch up to the discussion that preceded your participation in it.

laythor

Time to start an AP frequently asked questions thread Jeff!.. 1 post, stickied, then locked.

smokatoke

Sorry if this question has been beat to death, I promise I tried searching...

Based on all the mod combos you have built maps for, and based on pure data, is there is recognized "best" setup for an RX8? (naturally aspirated)

(Let me further clarify, BASED ON PURE DATA FROM BUILDING THOUSANDS OF MAPS... I know there are a million threads about mods and peoples opinions on best mods)

wcs

iTrader: (2)

Leave it stock.
Remove the catalytic if you can, seeing you are in CA maybe not an option for you.

Buy BHR Coils when OEM's are fried.

End of Line

Blacknightz

Remove the cat? Hmmmz... i thought it would create a mini loss in power when it is a straight pipe? Especially for autos...


Would a high flow cat be better?

WTBRotary!

iTrader: (6)

^^^ I believe the 8 doesnt Flow enough air for it to even matter... As for a power loss between a midpipe with a high-flow cat or not...