Notices
New Member Forum A place for new members to get their feet wet

04 4 port wont start

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old 04-08-2019, 09:10 PM
  #1  
New Member
Thread Starter
 
Jsteele1981's Avatar
 
Join Date: Apr 2019
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
04 4 port wont start

Ok I bought a no start rx8 have spark have fuel to the rail new fuel pump wont start. Tried the flooded cure but car is not flooded I dump gas in the throttle body and it runs till gas is gone. Before I got the car it has had the motor replaced and hasn't ran sence be sided putting gas in the throttle body. Any help would be appreciated
Old 04-08-2019, 09:20 PM
  #2  
FULLY SEMI AUTOMATIC
iTrader: (9)
 
200.mph's Avatar
 
Join Date: Aug 2008
Location: BALLS DEEP
Posts: 5,644
Received 2,376 Likes on 2,005 Posts
who did the motor install? did it run after new motor? was it a reman motor, rebuilt or junkyard?

ive seen a lot of no start after motor swaps from getting the fuel injectors connected wrong or not resetting the ess (20 brake stomp)
Old 04-08-2019, 09:24 PM
  #3  
New Member
Thread Starter
 
Jsteele1981's Avatar
 
Join Date: Apr 2019
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Used jap motor hasn't ran sence swap other than gas in the intake. Tried the 20 stomp tonight after I put a new pump in it. I can get the car to rev up to 6 k until it burn the fuel i put in it.
Old 04-08-2019, 09:27 PM
  #4  
FULLY SEMI AUTOMATIC
iTrader: (9)
 
200.mph's Avatar
 
Join Date: Aug 2008
Location: BALLS DEEP
Posts: 5,644
Received 2,376 Likes on 2,005 Posts
jap motors are a crap shoot. did you install it? i would double check the injectors
Old 04-08-2019, 09:30 PM
  #5  
New Member
Thread Starter
 
Jsteele1981's Avatar
 
Join Date: Apr 2019
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
I did not install unfortunately. I have been looking online for a diagram and cant seam to find a 4 port diagram
Old 04-08-2019, 09:46 PM
  #6  
New Member
Thread Starter
 
Jsteele1981's Avatar
 
Join Date: Apr 2019
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Is the any sensors that use the same plugs as the injectors? The upper injectors seam to be plugged in right the front one has the yellow tape and the back one is missing the tape but the wires seam to match what I found online. It was to dark to see the bottom ones.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
RJBCAL
Series I Trouble Shooting
7
06-06-2019 02:38 PM
Arxeight
Series I Trouble Shooting
11
10-16-2015 04:32 PM
ninetysixyenko
New Member Forum
4
02-07-2015 04:58 PM
sr101
Series I Trouble Shooting
34
08-05-2011 09:06 PM
RX-8Newb
RX-8 Discussion
21
06-22-2007 01:50 PM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: 04 4 port wont start



All times are GMT -5. The time now is 09:36 PM.