LS2 Build
#427
Legend In My Own Mind
Good stuff. Ask him tons of questions like that. You need to know what you are getting. Don't hate your car six months from now just because you spent a lot of money and despise one tiny issue. Clarity now will leave you happier later.
#428
j_tibo
Join Date: Feb 2011
Location: Ottawa...well Wendover
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
Yep that makes sense, you would need to find a location for the compressor, run some hard lines, figure out if you can use the stock condenser, and I'm sure the engine bay is looking pretty tight at the moment. I took my AC out, since the compressor was no good and I wasn't missing it, just one less thing in the way. Plus you'll hear that awesome Detroit muscle way better with the windows down!!!
Last edited by jay_tibo; 10-24-2012 at 06:41 AM.
#431
j_tibo
Join Date: Feb 2011
Location: Ottawa...well Wendover
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
#434
If you come up with a way to get the wiring set up to stock gauges please post up what you did. I swapped a Built LS1 into my 04 rx8 and just ended up getting after market gauges- tach, oil, water temp, etc..... I first used the stock rack but didn't like it much plus I needed more room for my sway bar mounting so I installed a Trans am WS6 rack. It runs and drives awesome but I would like to have the stock gauges instead of using aftermarket. Anyway, let me know if you figure it out. Thanks and good luck.
#435
Renesis out... REW in
iTrader: (3)
If you come up with a way to get the wiring set up to stock gauges please post up what you did. I swapped a Built LS1 into my 04 rx8 and just ended up getting after market gauges- tach, oil, water temp, etc..... I first used the stock rack but didn't like it much plus I needed more room for my sway bar mounting so I installed a Trans am WS6 rack. It runs and drives awesome but I would like to have the stock gauges instead of using aftermarket. Anyway, let me know if you figure it out. Thanks and good luck.
#436
If you come up with a way to get the wiring set up to stock gauges please post up what you did. I swapped a Built LS1 into my 04 rx8 and just ended up getting after market gauges- tach, oil, water temp, etc..... I first used the stock rack but didn't like it much plus I needed more room for my sway bar mounting so I installed a Trans am WS6 rack. It runs and drives awesome but I would like to have the stock gauges instead of using aftermarket. Anyway, let me know if you figure it out. Thanks and good luck.
#441
WENTGERMAN
iTrader: (6)
Well the re-wiring when this wiring doesn't work out, possible move to a stand alone unit, new upgraded axles, larger tires and wheels, purchase of gauges and gauge assembly plus wiring (Assuming all the stock sensors don't read, again because of wiring issues).
Then you have the rebuilding of the engine after a short amount of time, because regardless of the condition they say it was in you never really know.
Once all that is complete you should be good to go.
I'm sure there are some little things I left out, lots of unknowns with a project like this.
I've seen a few people try and fail right around where you are at with this build. Getting the engine in is the easy part.
Then you have the rebuilding of the engine after a short amount of time, because regardless of the condition they say it was in you never really know.
Once all that is complete you should be good to go.
I'm sure there are some little things I left out, lots of unknowns with a project like this.
I've seen a few people try and fail right around where you are at with this build. Getting the engine in is the easy part.
#444
my total cost out of pocket was 5500. I did everything myself in my garage. After selling parts I didn't need I ended up really spending about 1500 more than I expected. But really, its a project... I don't know if I will every be done with it. I'll do some things and be happy, then I'll want to change something else and do more work to it. Its a never ending cycle.
#449
I've been thinking about starting a thread but right now I just don't have the extra time. And I hate it when people start a thread and than never finish it (although I've done it in the past like an A**). So when my schedule slows I'll definitely do it. By the way, if you end up needing a bump steer kit for your swap (which I did) I had my buddy machine me one and he said he will sell them for 200 a set. Came with everything needed from outer tie rod ends to shims.
#450
ok, thank you sir. ill talk to him about it
edit- he said he fixed that problem. He said hell also message you to explain what we're doing with the gauges
edit- he said he fixed that problem. He said hell also message you to explain what we're doing with the gauges
Last edited by Blackbriar2189; 10-25-2012 at 07:43 PM.