NA SemiPP 20b
#1
Turbo 20b Swap (No longer NA)
Updated 5/14/2019 -
Looking for a new eshaft. The original one is out of alignment, and in such a way that it cannot be straightened. This will not effect it's use, but the RPM limit has been limited to 8500 RPMs by Rick Engman. That doesn't work for the NA plans, so I need to find a new one.
Goal 450WHP
Mazmart
B series motor purchased. Reliable source, and on the shelf.
Iron lapping
Built by Myles Fisher
Large Street Port, and semi pport
OE Seal kit
17pc Goopy 10mm stud kit
I-Rotay apex seals
Chip Motorsports
Rotor lightning, clearancing, and balancing 20b rotors
GOing to have to do the 9.7 rotors now... lightning, balance, scallop, and clearance.
Billet oil pan
Fabrication by Coffee Fabrication
Flaming River custom steering rack. Little faster ratio than stock
MK3 MR2 Electric power steering pump - eventually. May end up doing it myself.
370z transmission mounting.
Reverse mounted hood to open to the front - eventually
Drive-train / Engine Parts
Xcessive Engineering Short LIM
6x ID 1050 injectors
Adaptronic plug and play ECU
20b crossmember from Promaz
370z JK40C Transmission
Body
2012 Spirit R head lights
Autoexe Type C hood (Will be replaced with a one off hood by MPH Fabrication)
Autoexe duck-tail trunk
Leg Motorsports RX Vision front bumper (Being remolded by MPH Fabrication into dry carbon with carbon zylon inserts)
Lions Kit S2 over fenders - will replace with metal eventually.
Marsh Powerhouse Fabrication carbon zylon roof
RE Amamiya carbon tail lights
RE Amamiya AD Pro fender mirrors
Vertex Lang rear bumper
Vertex Lang side skirts (May change)
Misc Parts
Autoexe big brake kit
Autoexe S1 steering wheel
Autoexe ball type shift ****
90's Mazda Speed seats
Volk SF Challenge wheels
Looking for a new eshaft. The original one is out of alignment, and in such a way that it cannot be straightened. This will not effect it's use, but the RPM limit has been limited to 8500 RPMs by Rick Engman. That doesn't work for the NA plans, so I need to find a new one.
Goal 450WHP
Mazmart
B series motor purchased. Reliable source, and on the shelf.
Iron lapping
Built by Myles Fisher
Large Street Port, and semi pport
OE Seal kit
17pc Goopy 10mm stud kit
I-Rotay apex seals
Chip Motorsports
Rotor lightning, clearancing, and balancing 20b rotors
GOing to have to do the 9.7 rotors now... lightning, balance, scallop, and clearance.
Billet oil pan
Fabrication by Coffee Fabrication
Flaming River custom steering rack. Little faster ratio than stock
MK3 MR2 Electric power steering pump - eventually. May end up doing it myself.
370z transmission mounting.
Reverse mounted hood to open to the front - eventually
Drive-train / Engine Parts
Xcessive Engineering Short LIM
6x ID 1050 injectors
Adaptronic plug and play ECU
20b crossmember from Promaz
370z JK40C Transmission
Body
2012 Spirit R head lights
Autoexe Type C hood (Will be replaced with a one off hood by MPH Fabrication)
Autoexe duck-tail trunk
Leg Motorsports RX Vision front bumper (Being remolded by MPH Fabrication into dry carbon with carbon zylon inserts)
Lions Kit S2 over fenders - will replace with metal eventually.
Marsh Powerhouse Fabrication carbon zylon roof
RE Amamiya carbon tail lights
RE Amamiya AD Pro fender mirrors
Vertex Lang rear bumper
Vertex Lang side skirts (May change)
Misc Parts
Autoexe big brake kit
Autoexe S1 steering wheel
Autoexe ball type shift ****
90's Mazda Speed seats
Volk SF Challenge wheels
Last edited by reddozen; 05-14-2019 at 11:25 PM. Reason: A lot has changed...
#2
FULLY SEMI AUTOMATIC
iTrader: (9)
tag
#5
#6
Registered
Sweet, I can't wait to see what your intake manifold(s) will look like.
I remember when 20B were only a few grand not too long ago on ebay. Now you gotta spend 7k, and not even be guaranteed that the motor isn't junk.
I remember when 20B were only a few grand not too long ago on ebay. Now you gotta spend 7k, and not even be guaranteed that the motor isn't junk.
Last edited by strokercharged95gt; 03-07-2017 at 11:15 AM.
#7
FULLY SEMI AUTOMATIC
iTrader: (9)
red can you post some pics of the motor build when its happening?
#8
Really depends on the builder. he's not touching it till May, and doesn't expect it complete till June / July. I'll ask, but I don't want to inconvenience him. I'm sure he'd take a couple though.
#9
FULLY SEMI AUTOMATIC
iTrader: (9)
i figured since it was mazmart they would snap some pics for ya. great company
The following users liked this post:
east00 (03-27-2020)
The following users liked this post:
zoom44 (07-28-2019)
#18
Some people might be curious about the rest of the car...
LEG Motorsports RX8-Vision carbon front bumper
Vertex Lang sides and rear bumper
Panspeed wide front and rear fenders
AutoExe SE03 hood
AutoExe SE02 duktail trunk
RE Amemiya carbon tail lights and AD Pro fender mirrors
Probably a couple more things before it goes to paint (after the engine).
LEG Motorsports RX8-Vision carbon front bumper
Vertex Lang sides and rear bumper
Panspeed wide front and rear fenders
AutoExe SE03 hood
AutoExe SE02 duktail trunk
RE Amemiya carbon tail lights and AD Pro fender mirrors
Probably a couple more things before it goes to paint (after the engine).
The following users liked this post:
zoom44 (07-28-2019)
#19
FULLY SEMI AUTOMATIC
iTrader: (9)
this thread is enough goddamn reason to give us the like button back
The following users liked this post:
zoom44 (07-28-2019)
The following users liked this post:
LeftyTheNub (12-05-2017)
The following users liked this post:
Federighi (05-15-2019)
#22
Registered
Nice work! I wouldn't even want to sit in those and potentially ruin them.
#24
FULLY SEMI AUTOMATIC
iTrader: (9)
red i love your build but hate the color red and i gotta agree with 9k on the seats