Reeiss's project
#28
Bikes are Rotaries
Join Date: Feb 2013
Location: Kerikeri, NZ
Posts: 303
Likes: 0
Received 0 Likes
on
0 Posts
By "plasti dip" do you mean spray paint as I would like to do the same. Black badges on a black car!!
#31
Apples and bananas
Thread Starter
Join Date: Sep 2012
Location: Norway
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
Got my full Ings bodykit today!
![](http://imageshack.us/a/img42/2719/cx74.jpg)
Going to test fit it next week, and if its okay then Ill take it do a bodyshop and have it painted. Installing it myself.
Btw. Anyone here that can read japanese?
![](http://imageshack.us/a/img9/589/i5lx.jpg)
![](http://imageshack.us/a/img42/2719/cx74.jpg)
Going to test fit it next week, and if its okay then Ill take it do a bodyshop and have it painted. Installing it myself.
Btw. Anyone here that can read japanese?
![](http://imageshack.us/a/img9/589/i5lx.jpg)
![](http://imageshack.us/a/img13/9503/6f6i.jpg)
#32
Apples and bananas
Thread Starter
Join Date: Sep 2012
Location: Norway
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
Happy with the result. Almost looks like a new car.
![](http://imageshack.us/a/img94/9670/xh2i.jpg)
![](http://imageshack.us/a/img822/2694/02ia.jpg)
![](http://imageshack.us/a/img849/2433/zz4p.jpg)
Going to give the car a cleaning tomorrow and then fix a little bit on the kit. Then do a photo shoot-
![](http://imageshack.us/a/img94/9670/xh2i.jpg)
![](http://imageshack.us/a/img822/2694/02ia.jpg)
![](http://imageshack.us/a/img849/2433/zz4p.jpg)
Going to give the car a cleaning tomorrow and then fix a little bit on the kit. Then do a photo shoot-
#34
Apples and bananas
Thread Starter
Join Date: Sep 2012
Location: Norway
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
I installed out myself.
The fitment is good, but a little of by the side markers. It's an easy fix, I believe. I'm going to sand out down around 3mm and the fitment will be flush.
With side skirt, I did drill holes and filled in with some anti rust and sealant were the screws goes.
But I guess you could just use double side tape and some sealant.
There is a 1 or 2 mm gap on each end. Plan is to fill it with silicon and brush red paint over it.
On the rear exhaust covers it's a perfect fitment, except were the black parts meet. I used black sealant too remove a 2-3mm gap. I'm going to apply some more, sand it down and spay paint the whole black part of the car on the rear.
The fitment is good, but a little of by the side markers. It's an easy fix, I believe. I'm going to sand out down around 3mm and the fitment will be flush.
With side skirt, I did drill holes and filled in with some anti rust and sealant were the screws goes.
But I guess you could just use double side tape and some sealant.
There is a 1 or 2 mm gap on each end. Plan is to fill it with silicon and brush red paint over it.
On the rear exhaust covers it's a perfect fitment, except were the black parts meet. I used black sealant too remove a 2-3mm gap. I'm going to apply some more, sand it down and spay paint the whole black part of the car on the rear.
#36
Apples and bananas
Thread Starter
Join Date: Sep 2012
Location: Norway
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
You can't go wrong with Ings :D
Not sure, but I kinda like these
![](http://nw-built.com/wp-content/uploads/2010/09/sean-rx8-2-copy.jpg)
MB Battles
It started snowing here, so I'll put on my winter wheels. And won't be buying new wheels until spring.
Btw I didn't use silicon after all, found out that you can't paint over silicon. So I used adhesive sealant.
Not sure, but I kinda like these
![](http://nw-built.com/wp-content/uploads/2010/09/sean-rx8-2-copy.jpg)
MB Battles
It started snowing here, so I'll put on my winter wheels. And won't be buying new wheels until spring.
Btw I didn't use silicon after all, found out that you can't paint over silicon. So I used adhesive sealant.
Thread
Thread Starter
Forum
Replies
Last Post
Learners_Permit
Series I Interior, Audio, and Electronics
8
09-27-2015 07:38 PM