{ FS } Engine Block Partout! - 05 6MT w/ 99k - Rotors, Housings, Irons, and More!
#1
New Member
Thread Starter
iTrader: (1)
Join Date: Feb 2011
Location: Connecticut
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Engine Block Partout! - Rear Rotor, Iron, & Housing; OMP; Oil Pan + More
Category: Engine - Intake/Fuel
Price: $1
Private or Vendor Listing: Private Listing
Part Fits (you may select multiples): Series I
Location (US State/Canada/Int): CT
Item Condition: Used
Prices and Pictures for New Parts are listed immediate below:
These parts are from a 2006 MT with 70k. The engine lost an apex seal on the front rotor, damaging that rotor, housing, and both intermediates. These are the parts I have left over.
Items are located in Meriden, CT
All Prices are OBO and buyer pays shipping.
Because of my low post count, please feel free to check the links in my signature to my other accounts as a vote of confidence.
For quickest feedback, comment in this thread or email me at adshain@gmail.com
Thanks,
Alex
--------------------------------------------------------------------------------------------------------
SOLD - Rear Rotor Housing – Great shape, no chrome flake or gouging
$200
Pic1
Pic2
Pic3
Rear Rotor – Good bearing, side seal slots are fine, apex seals look a bit worn but not damaged.
$150
Apex1
Apex2
Apex3
Stamp
Face
Bearing
Rear Iron – Good shape, minimal step wear, No grooves , All ports are good.
$100
Pic1
Oil Metering Pump– Passes factory service manual resistance test, no damage to housing or plastic
$200
Pic1
Oil Metering Pices - No cracks or leaks
$25
Pic1
Coils – Supposedly replaced a few months before the front rotor died, includes 4 coils, no bracket. Sorry, no pic.
$50
Upper Intake, Solenoids, and Oil Filler - No cracks or damage, Includes knockoff mazdaspeed filler cap
$70
Pic1
Pic2
Oil Pan - No major dents or damage
$40
--------------------------------------------------------------------------------------------------------
COLOR="blue"]
Rotor #1[/COLOR] $225
PIC: Face 1
PIC: Face 2
PIC: Apex Groove 1
PIC: Apex Groove 2
PIC: Apex Groove 3
Rotor #2 $225
PIC: Face 1
PIC: Face 2
PIC: Apex Groove 1
PIC: Apex Groove 2
PIC: Apex Groove 3
--------------------------
Rotor Housings: Average chrome flaking for mileage. Could work for a budget rebuild or for display purposes.
Housing #1 $60 $45
PIC: Bottom face
PIC: Top Face
Housing #2 $60 $45
PIC: Bottom face
PIC: Top Face
--------------------------
Side Housings / Irons: In great shape with average wear for mileage.
Front Iron $150 $100
PIC: Front Iron
Center Iron $150 $100
PIC: Center Iron Front Side
PIC: Center Iron Rear Side
Rear Iron* $70 $50 *In great shape, but has a tension bolt stuck in a lower stud hole. Would be completely usable with a little work.
--------------------------
Misc.: Front Cover w/IGN pickup and tensioner $60 $45
PIC: Front Cover
Last edited by shainiac; 01-14-2015 at 10:16 AM.
#8
New Member
Thread Starter
iTrader: (1)
Join Date: Feb 2011
Location: Connecticut
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Really? Last time I checked new rotors from Mazda are almost $700. I have the housings listed for chump change because, as I said, they are display quality, but the motor did RUN. "Kissed" the irons? Those are water spots from sitting in my garage before I oiled them up. Please keep the thread shitting to a minimum. I am new to RX-8s and therefore what everything goes for. All my prices are based on what I've seen other people selling them for and what sells on eBay, and everything is OBO. If you think my prices are out of line, send me a PM and we can negotiate, otherwise, be polite
#16
New Member
Thread Starter
iTrader: (1)
Join Date: Feb 2011
Location: Connecticut
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
SOLD - Rear Rotor Housing – Great shape, no chrome flake or gouging
$200
Pic1
Pic2
Pic3
Rear Rotor – Good bearing, side seal slots are fine, apex seals look a bit worn but not damaged.
$150
Apex1
Apex2
Apex3
Stamp
Face
Bearing
Rear Iron – Good shape, minimal step wear, No grooves , All ports are good.
$100
Pic1
Oil Metering Pump– Passes factory service manual resistance test, no damage to housing or plastic
$200
Pic1
Oil Metering Pices - No cracks or leaks
$25
Pic1
Coils – Supposedly replaced a few months before the front rotor died, includes 4 coils, no bracket. Sorry, no pic.
$50
Upper Intake, Solenoids, and Oil Filler - No cracks or damage, Includes knockoff mazdaspeed filler cap
$70
Pic1
Pic2
Oil Pan - No major dents or damage
$40
$200
Pic1
Pic2
Pic3
Rear Rotor – Good bearing, side seal slots are fine, apex seals look a bit worn but not damaged.
$150
Apex1
Apex2
Apex3
Stamp
Face
Bearing
Rear Iron – Good shape, minimal step wear, No grooves , All ports are good.
$100
Pic1
Oil Metering Pump– Passes factory service manual resistance test, no damage to housing or plastic
$200
Pic1
Oil Metering Pices - No cracks or leaks
$25
Pic1
Coils – Supposedly replaced a few months before the front rotor died, includes 4 coils, no bracket. Sorry, no pic.
$50
Upper Intake, Solenoids, and Oil Filler - No cracks or damage, Includes knockoff mazdaspeed filler cap
$70
Pic1
Pic2
Oil Pan - No major dents or damage
$40
Last edited by shainiac; 01-14-2015 at 10:17 AM.
Thread
Thread Starter
Forum
Replies
Last Post
Espo
RX-8 Parts For Sale/Wanted
36
06-08-2017 03:53 PM
Vlaze
RX-8 Parts For Sale/Wanted
26
10-15-2012 03:36 PM