{ FS } R3 Seats nearly Mint. Front and Rear Kansas City
#1
R3 Seats nearly Mint. Front and Rear Kansas City
Category: Interior
Price: $1900
Private or Vendor Listing: Private Listing
Part Fits (you may select multiples): Series I, Series II
Location (US State/Canada/Int): KS
Item Condition: Used
$1900 for the set of four
These are VERY comfortable seats, and way better than the stock at holding you in for high cornering loads.
These seats are nearly mint, and ready to be bolted into your Rx8
The Airbags are intact
The wiring harness are complete and unmolested
The seats are clean and show virtually no wear to the leather or the cloth
Price includes Both front seats, all four pieces of the rear seats;
Includes the rails and sliders; and
Includes the plastic trim pieces that covers the rails.
The seats smell good, like clean leather. I've a very sensitive nose to cigarette smoke, and these seats have none of that smell.
I want to sell the entire set to someone that wants to swap in fronts and rears. If the set doesn't sell I'll break it into fronts and backs next week.
Full disclosure:
I took closeup pics of the three not perfect areas (see the pics in the first reply):
1) the drivers cushion has a small (1/16th inch) burn mark. I suspect a solder blob when someone installed the aftermarket stereo. It's on the surface of the cloth, not through it, so it shouldn't rip, or grow. In fact it's nearly unnoticeable
2) The rear driver cushion has two similar, but even smaller (1/32 inch imperfections. same story, not noticeable.
3)Someone once spilled a soda on the back seats. ZERO evidence exists on the top. The whole seat top and bottom it's perfectly clean. The underside foam is discolored from the spill, and is the only remaining evidence. No smells, not sticky. I just wanted to be 100% up front.
Please PM me for more info / better pics of whatever you want.
Shipping is additional, and is likely to be $100-$150 at a minimum. I just shipped a set of vintage front only Recaros and it was a 105 lb box and $100. I suspect this box will weigh in at 150lbs
Thanks,
Richard in Kansas City
#9
I personally did not try. I have read here where people have bolted the R3 Seats into the Series one.
I measured the bolt holes of these r3 seats, and they measured out the the same spacing as what my S1 seat bolts are located at.
I would love to have someone who has these seats in the S1 comment in.
Richard
I measured the bolt holes of these r3 seats, and they measured out the the same spacing as what my S1 seat bolts are located at.
I would love to have someone who has these seats in the S1 comment in.
Richard
#10
I have the full R3 Interior in my car every thing is 100% Bolt in/plug in... The only thing is the one of the plugs for the drivers side window switches is different than the Series 1, I just reused the original switch panels. That doesn't apply here though... the seats WILL fit a Series 1!
#16
He means that the details are being finalized and for all intents and purposes the R3 recaros are sold.
The second part is a reference to the fact that junirol has some aftermarket seats that he will no longer be needing and will assumedly be selling them since he now has pure sexerific seats.
The second part is a reference to the fact that junirol has some aftermarket seats that he will no longer be needing and will assumedly be selling them since he now has pure sexerific seats.
#17
I special ordered some bride rails couple of weeks ago, I couldn't cancel the order at this point. I should be getting them sometime early/mid September o.O I canceled the passenger seat but I already picked up the driverside. So when I get these installed I'll have a set of OEM cloth seats, and aftermarket bride rails and driverside seat to sell... So if anyone is interested I can get back with them once I get the rails...
#19
Thread
Thread Starter
Forum
Replies
Last Post
{FS/WTT} 04 Black Rx-8 TRACK AUTOX TIMEATTACK
Billy Marcial
RX-8's For Sale/Wanted
5
03-01-2018 07:50 AM
akagc
RX-8's For Sale/Wanted
7
08-11-2015 08:07 PM