The Official "RX8 in DSP" Thread
#826
FINALLY getting the chance to revisit the RX8 a bit, got distracted racing motorcycles...
Got the thing painted (not to shabby if I say so myself), and I think I have given up on keeping the battery in the engine bay. Anyone have any suggestions for a good battery post setup for under the hood? I'd like to have the cables running to the trunk mounted in an appealing way in the front.
Also, I stumbled upon a cheap set of FCM coilovers I think I am going to pick up and get Shaikh to rebuild/revalve... A close friend has been absolutely swearing by the customer support and willingness to work towards custom setups at Feal though, and that would cost less than the revalve/rebuild on the FCMs.
Too many things to consider...
Got the thing painted (not to shabby if I say so myself), and I think I have given up on keeping the battery in the engine bay. Anyone have any suggestions for a good battery post setup for under the hood? I'd like to have the cables running to the trunk mounted in an appealing way in the front.
Also, I stumbled upon a cheap set of FCM coilovers I think I am going to pick up and get Shaikh to rebuild/revalve... A close friend has been absolutely swearing by the customer support and willingness to work towards custom setups at Feal though, and that would cost less than the revalve/rebuild on the FCMs.
Too many things to consider...
For the coilovers, I don't know if you saw this or not but there is a set of Penske 8300 DA (remote) dampers on Miata.net for sale. The guy is asking $1750 shipped. The springs are wrong, and they would need to be revalved (they have linear/linear valving) but that's a steal for a set of good shocks, and the double digressive valving is not expensive. Maybe you can even talk him down. I just bought a set of Penskes for $1800 shipped and felt it was a good price...
#827
Registered
iTrader: (2)
For the battery, cut off the stock positive clamp in the engine bay and crimp / solder / shrinkwrap on a junction to re-route that wire to wherever you want it in the trunk. You could also remove the stock positive wire from the wiring harness and re-wire it with a dedicated line if you don't want to use a junction. I did this with my STS build years ago and got clarification it was legal so it would be fine in Street Prepared. Unless you really like having a battery post setup in the engine bay. Wire the negative in the trunk with a short wire between the battery and the unibody. Just be careful when you wire in the ground to make sure the engine (starter) has a good 1-2AWG ground to the chassis in the engine bay.
For the coilovers, I don't know if you saw this or not but there is a set of Penske 8300 DA (remote) dampers on Miata.net for sale. The guy is asking $1750 shipped. The springs are wrong, and they would need to be revalved (they have linear/linear valving) but that's a steal for a set of good shocks, and the double digressive valving is not expensive. Maybe you can even talk him down. I just bought a set of Penskes for $1800 shipped and felt it was a good price...
For the coilovers, I don't know if you saw this or not but there is a set of Penske 8300 DA (remote) dampers on Miata.net for sale. The guy is asking $1750 shipped. The springs are wrong, and they would need to be revalved (they have linear/linear valving) but that's a steal for a set of good shocks, and the double digressive valving is not expensive. Maybe you can even talk him down. I just bought a set of Penskes for $1800 shipped and felt it was a good price...
The following users liked this post:
comebackqid (03-14-2018)
#829
That is a good deal on the Penskes! After getting them reworked and all I'd probably blow most of my budget for the season just on those though... At this point it looks like I can get the FCM setup for around $2600 with new springs and revalve... I'm honestly not sure what the better option is.
Send those off to Ankeny or Anze and have them revalved -- of course, driver preference on spring rates. I'm sure they'd be willing to give their input as well.
If not, I'm fairly sure I can find someone locally who'd be willing to buy those, if you're not.
#830
Registered
iTrader: (2)
Looks like for those Penskes, there isn't any front top hats. Believe it or not, the ND uses the same top hat bolt pattern as the NC/RX-8 -- so I bought a set from SakeBomb and had a friend bore out the spacer for the Penske 12 mm shaft.
Send those off to Ankeny or Anze and have them revalved -- of course, driver preference on spring rates. I'm sure they'd be willing to give their input as well.
If not, I'm fairly sure I can find someone locally who'd be willing to buy those, if you're not.
Send those off to Ankeny or Anze and have them revalved -- of course, driver preference on spring rates. I'm sure they'd be willing to give their input as well.
If not, I'm fairly sure I can find someone locally who'd be willing to buy those, if you're not.
Finding top hats should be TOO hard I would think.
#831
Before you buy top hats, verify the shaft diameter. There are a bunch of options.
#832
https://anzesuspension.com/wp-conten...Price-List.pdf
Looks like 1060 for a set of 4. Probably budget about 75 for shipping both ways, and an extra 150 for consumables (I'd replace the spherical bearings in the rear shocks).
And John is definitely right about figuring out what the shaft stud diameter is -- I swapped my rears out for the 10 mm (but they're $$$, bought separately).
#833
I would give up other parts in the budget and spend your money on good shocks. They are the #1 thing we did to my car. Next was having Jeff H help us dial them in ![Lol](https://www.rx8club.com/images/smilies/lol.gif)
Also, you can run them with the stock front top hats. It's not ideal (some side loading) but we did for awhile. We now have spherical top hats front and rear.
![Lol](https://www.rx8club.com/images/smilies/lol.gif)
Also, you can run them with the stock front top hats. It's not ideal (some side loading) but we did for awhile. We now have spherical top hats front and rear.
#834
Registered
For the battery, cut off the stock positive clamp in the engine bay and crimp / solder / shrinkwrap on a junction to re-route that wire to wherever you want it in the trunk. You could also remove the stock positive wire from the wiring harness and re-wire it with a dedicated line if you don't want to use a junction. Wire the negative in the trunk with a short wire between the battery and the unibody. Just be careful when you wire in the ground to make sure the engine (starter) has a good 1-2AWG ground to the chassis in the engine bay.
I have a very similar setup; bolted a positive lead to the OEM positive terminal in the engine bay, re-grounded all of the negatives to the front chassis member behind the fans, ran the positive lead to the trunk, ran a short negative chassis ground from the negative terminal.
BUT, i did not make any changes along the lines of "Just be careful when you wire in the ground to make sure the engine (starter) has a good 1-2AWG ground to the chassis in the engine bay". How is the factory starter grounded, and/or why is it good to improve this ground? I am having somewhat slow cranking and i assume this could be contributing. Is the old starter ground connected directly to the battery negative?
#835
What am I doing here?
Join Date: Mar 2006
Location: 2017 Miata RF Launch Edition
Posts: 3,606
Received 649 Likes
on
510 Posts
Unless I'm mistaken, the starter is grounded through the engine/transmission.
I think John's point is that you need to make sure that the grounding wires between engine and chassis are in good shape if you connected your negative battery terminal to the chassis.
I think John's point is that you need to make sure that the grounding wires between engine and chassis are in good shape if you connected your negative battery terminal to the chassis.
#836
Most cars have the negative cable from the battery connected directly to the engine, so any ground wires from the engine to the transmission are relatively small (high numerical gauge) wire. If you relocate the battery to, say, the trunk, you need to add a high current (low numerical gauge) wire between the engine and the unibody.
John
#837
I searched the thread but didn't see any discussion about motor and diff mounts. Has anyone had success eliminating wheel hop from launching on Hoosiers?
I found the following motor mount options:
- RX8Performance $265 aluminum 70A poly
- Black Halo Racing $395 aluminum ?A poly
- Race-Roots $200 stainless ?A poly
- Megan Racing $307 ?metal 70A rubber
Here are the differential bushings I found:
- Whiteline $36 ?A poly
- Powerflex Purple/Black $77/86 80/95A poly (street/race)
- Superpro $69 70/80A poly (street/race)
I'm sure I've missed some. Is 70A durometer enough to control things in the rear?
I found the following motor mount options:
- RX8Performance $265 aluminum 70A poly
- Black Halo Racing $395 aluminum ?A poly
- Race-Roots $200 stainless ?A poly
- Megan Racing $307 ?metal 70A rubber
Here are the differential bushings I found:
- Whiteline $36 ?A poly
- Powerflex Purple/Black $77/86 80/95A poly (street/race)
- Superpro $69 70/80A poly (street/race)
I'm sure I've missed some. Is 70A durometer enough to control things in the rear?
#838
Doing solid (Delrin / Aluminum) bushings in the subframe and diff of the BMW cured all the wheel hop issues. I would expect the same is true of the RX-8.
Polyurethane is not a good bushing material and IMO should never be used. For anything.
Polyurethane is not a good bushing material and IMO should never be used. For anything.
The following users liked this post:
sharingan 19 (07-08-2021)
#839
Looks like for those Penskes, there isn't any front top hats. Believe it or not, the ND uses the same top hat bolt pattern as the NC/RX-8 -- so I bought a set from SakeBomb and had a friend bore out the spacer for the Penske 12 mm shaft.
Send those off to Ankeny or Anze and have them revalved -- of course, driver preference on spring rates. I'm sure they'd be willing to give their input as well.
If not, I'm fairly sure I can find someone locally who'd be willing to buy those, if you're not.
Send those off to Ankeny or Anze and have them revalved -- of course, driver preference on spring rates. I'm sure they'd be willing to give their input as well.
If not, I'm fairly sure I can find someone locally who'd be willing to buy those, if you're not.
https://forum.miata.net/vb/showthread.php?t=660886
And they look to have top hats included.
#840
I see that RX8 Performance offers both Delrin diff bushings and aluminum subframe bushings, with a $50 option to have the diff bushings installed (+$150 core). I wish I had noticed that before I bought a spare diff carrier.
#841
I was hoping to avoid going that stiff since my car will be street driven. I don't believe I've experienced driving a car with delrin diff bushings before, though. Is it a perceptible vibration or just more of a noise thing?
I see that RX8 Performance offers both Delrin diff bushings and aluminum subframe bushings, with a $50 option to have the diff bushings installed (+$150 core). I wish I had noticed that before I bought a spare diff carrier.
I see that RX8 Performance offers both Delrin diff bushings and aluminum subframe bushings, with a $50 option to have the diff bushings installed (+$150 core). I wish I had noticed that before I bought a spare diff carrier.
#843
We made delrin diff bushings. They did help the wheel hop some, but it's still there just reduced. We did a mix of poly and delrin suspension bushings everywhere - some of them in the rear are slight compliance bushings so we were a little worried about going delrin (and also the front lower rear control arm is definitely a compliance bushing, so we kept it OEM). Our engine mounts we DIY filled the OEM ones with 90A poly (I think). Not sure that's the best solution but it was better than OEM. We are still on stock subframe bushings - maybe we should consider swapping them for something stiffer.
We found messing with shock settings could actually dial out some of the wheel hop too.
We found messing with shock settings could actually dial out some of the wheel hop too.
#844
I was just being snarky. Bushings are usually pretty easy to make and you can typically save a lot of money making your own. I made mine because at the time the available aftermarket solutions were not legal for SP. Rules have changed since then.
To answer your question about NVH, yes, delrin / aluminum bushings definitely increase NVH. With the BMW, the first thing I did was the delrin engine mounts (because the car came with a broken engine mount and I needed something fast), and that increased NVH dramatically. When I made the subframe and diff bushings a year later I didn't notice that it really made much of an NVH change, but all the wheel hop went away.
Polyurethane is a terrible bushing material. I usually recommend to people that are considering poly because they don't want a lot of NVH to just use stock rubber. It's just better in every way.
To answer your question about NVH, yes, delrin / aluminum bushings definitely increase NVH. With the BMW, the first thing I did was the delrin engine mounts (because the car came with a broken engine mount and I needed something fast), and that increased NVH dramatically. When I made the subframe and diff bushings a year later I didn't notice that it really made much of an NVH change, but all the wheel hop went away.
Polyurethane is a terrible bushing material. I usually recommend to people that are considering poly because they don't want a lot of NVH to just use stock rubber. It's just better in every way.
#845
Registered
iTrader: (2)
I'm still on the hunt for suspension things... stumbled across these: eBay Penskes
Looks like having Anze rework these could be a very cost effective option.
Looks like having Anze rework these could be a very cost effective option.
#846
I'm still on the hunt for suspension things... stumbled across these: eBay Penskes
Looks like having Anze rework these could be a very cost effective option.
Looks like having Anze rework these could be a very cost effective option.
![Lol](https://www.rx8club.com/images/smilies/lol.gif)
#847
Registered
iTrader: (2)
![Eyetwitch](https://www.rx8club.com/images/smilies/eyetwitch.gif)
The one thing I was looking forward to with FCM was not having to worry about the spring rate/bump stop/sway bar decisions since he has experience with the chassis, going with the Penskes means I'll be doing a bit more testing and playing with it.
Would anyone be willing to divulge their numbers on here?
#849
![Eyetwitch](https://www.rx8club.com/images/smilies/eyetwitch.gif)
The one thing I was looking forward to with FCM was not having to worry about the spring rate/bump stop/sway bar decisions since he has experience with the chassis, going with the Penskes means I'll be doing a bit more testing and playing with it.
Would anyone be willing to divulge their numbers on here?
Also, each driver can have very different preferences, so what works for one may not work for another. For example, we don't run bump stops - our spring rates are stiff enough and we have enough shock travel that we never bottom them to need them (our shocks were custom built for our setup, most shocks need bump stops). Sam Strano tends to run softer setups that use bump stops I believe, and it obviously works very well (JV's car, for example). I'm sure Sam could help you a lot if you want to take that approach.
Also, aero vs no aero changes the setup quite a bit. We had to stiffen the rear a lot once we added the rear ducktail. Keep that in mind if you look at STX setups as a starting point, since they don't run aero.
#850
For anyone interested in more details on our build, Mazda Motorsports asked me to do a writeup on the basics of how to build a DSP RX8, including costs. The article outlines all of the parts on our car and the steps we took to make it competitive. I know some of you guys are still early in the development stage, so hopefully this may be helpful.
The only part not mentioned was the lightweight clutch, since the original manufacturer didn't work out like we hoped. We should know on the new one by early April once events get started again. A lightweight clutch did do wonders for our car though, when it worked.
https://www.mazdamotorsports.com/201...d-tips-budget/
The only part not mentioned was the lightweight clutch, since the original manufacturer didn't work out like we hoped. We should know on the new one by early April once events get started again. A lightweight clutch did do wonders for our car though, when it worked.
https://www.mazdamotorsports.com/201...d-tips-budget/
The following 3 users liked this post by Tamra: