DIY: Code your own key / remote
11-11-2010, 02:17 PM
#352
Ohio State
iTrader: (1)
Join Date: Jun 2005
Location: Back in Cincinnati, Ohio
Posts: 220
Likes: 0
Received 0 Likes
on
0 Posts
Just got my switchblade today...
totally works on my 2004 MT...
unit i bough on ebay:
FCC ID: KPU41788
IC : 4238A-41525
VISTEON 41525
i just followed this instructions: (few modification to be more NOOB friendly like me)
Remote Programming
• Ensure that all doors, trunk, and hood are closed,
• open the driver’s door
Carry out the operation below within 24 seconds:
• Insert key
• Turn ignition to the run position and off, 3 times (on-off, on-off, on-off)
• Leave key in ignition (off position, not lock or on)
• Push door switch, 3 times (The door switch is the little rubber one on the jamb of the rear door next to your elbow when sitting in the driver’s seat, which controls the interior lights.)
• Car will lock, then unlock automatically after pressing the door switch 3 times
• While the car is in unlock mode, Push 'Lock' on your newly acquired remote 2 times, (some suggest unlock, so try both)
• You will notice after pressing the Lock button on your remote, Car will lock, then unlock automatically again.
• Take out you key on the ignition and test your remote.
If it doesn't work, wait for a minute or so and repeat the procedure
NOTE: I DONT HAVE any existing remote. so no need to have an existing remote to do this procedure
One question though, i notice on most Rx8, when pressing the lock button on the remote the horn will honk, but mine doesn't have... anything i missed?
totally works on my 2004 MT...
unit i bough on ebay:
FCC ID: KPU41788
IC : 4238A-41525
VISTEON 41525
i just followed this instructions: (few modification to be more NOOB friendly like me)
Remote Programming
• Ensure that all doors, trunk, and hood are closed,
• open the driver’s door
Carry out the operation below within 24 seconds:
• Insert key
• Turn ignition to the run position and off, 3 times (on-off, on-off, on-off)
• Leave key in ignition (off position, not lock or on)
• Push door switch, 3 times (The door switch is the little rubber one on the jamb of the rear door next to your elbow when sitting in the driver’s seat, which controls the interior lights.)
• Car will lock, then unlock automatically after pressing the door switch 3 times
• While the car is in unlock mode, Push 'Lock' on your newly acquired remote 2 times, (some suggest unlock, so try both)
• You will notice after pressing the Lock button on your remote, Car will lock, then unlock automatically again.
• Take out you key on the ignition and test your remote.
If it doesn't work, wait for a minute or so and repeat the procedure
NOTE: I DONT HAVE any existing remote. so no need to have an existing remote to do this procedure
One question though, i notice on most Rx8, when pressing the lock button on the remote the horn will honk, but mine doesn't have... anything i missed?
Do you know if this will work on the 07 wireless key fob? I am having problems with my wireless key fob.
11-25-2010, 10:36 PM
#353
weeeeeeeeee
iTrader: (12)
saw this on dhgate tonight... might be an easy fix for those that don't have a second key for programming.
http://www.dhgate.com/high-quality-a...3775f4bb1.html
http://www.dhgate.com/high-quality-a...3775f4bb1.html
12-04-2010, 04:26 PM
#354
Registered User
Join Date: Nov 2010
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
K1nG,They need for VIN number just for data logging. Mazda obviously does not want to give a RX-8 chipped key to anyone. There is no "special" key for your car. Most RX-8 key should be generatic for all RX-8 models *(4 port or 6 port)mercury273,Valet key should have a chip in it since it can start a car. So theoretically you can use it as a 2nd coded key.WDS DOES NOT code keys - it is simply bullshit and the identification tag is at your ignition of your car (not the WDS). If so WDS can start your car without your key and why do they want you to leave your set of keys behind for service then . Hope this helps.
12-28-2010, 01:09 PM
#356
Special Agent Member
Join Date: Nov 2003
Location: Pine Bluff, AR
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Just purchased a switchblade Key/Remote Combo from the Ebay Dealer Midwestkeyless for $47.27 shipped.
Listed as "MAZDA KEY KEYLESS ENTRY REMOTE FOB SWITCHBLADE KPU41788"
I just got it cut and programmed with 2 original keys. Worked flawlessly per instructions on the 1st page.
Remote also programmed 1st time with ease, again, as per instructions on the 1st page.
Thanks for all the great info on here!
2004 M/T Rx8
Listed as "MAZDA KEY KEYLESS ENTRY REMOTE FOB SWITCHBLADE KPU41788"
I just got it cut and programmed with 2 original keys. Worked flawlessly per instructions on the 1st page.
Remote also programmed 1st time with ease, again, as per instructions on the 1st page.
Thanks for all the great info on here!
2004 M/T Rx8
Last edited by Rx8Freehk; 12-28-2010 at 01:11 PM. Reason: added price
01-02-2011, 05:49 AM
#357
Registered
Join Date: Apr 2009
Posts: 918
Likes: 0
Received 0 Likes
on
0 Posts
Just purchased a switchblade Key/Remote Combo from the Ebay Dealer Midwestkeyless for $47.27 shipped.
Listed as "MAZDA KEY KEYLESS ENTRY REMOTE FOB SWITCHBLADE KPU41788"
I just got it cut and programmed with 2 original keys. Worked flawlessly per instructions on the 1st page.
Remote also programmed 1st time with ease, again, as per instructions on the 1st page.
Thanks for all the great info on here!
2004 M/T Rx8
Listed as "MAZDA KEY KEYLESS ENTRY REMOTE FOB SWITCHBLADE KPU41788"
I just got it cut and programmed with 2 original keys. Worked flawlessly per instructions on the 1st page.
Remote also programmed 1st time with ease, again, as per instructions on the 1st page.
Thanks for all the great info on here!
2004 M/T Rx8
what do u mean have it cut?
Sorryz, noob...
01-03-2011, 11:27 PM
#359
Registered User
Join Date: Dec 2010
Location: Pennsylvania
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Just purchased a switchblade Key/Remote Combo from the Ebay Dealer Midwestkeyless for $47.27 shipped.
Listed as "MAZDA KEY KEYLESS ENTRY REMOTE FOB SWITCHBLADE KPU41788"
I just got it cut and programmed with 2 original keys. Worked flawlessly per instructions on the 1st page.
Remote also programmed 1st time with ease, again, as per instructions on the 1st page.
Thanks for all the great info on here!
2004 M/T Rx8
Listed as "MAZDA KEY KEYLESS ENTRY REMOTE FOB SWITCHBLADE KPU41788"
I just got it cut and programmed with 2 original keys. Worked flawlessly per instructions on the 1st page.
Remote also programmed 1st time with ease, again, as per instructions on the 1st page.
Thanks for all the great info on here!
2004 M/T Rx8
Last edited by Atticus6314; 01-03-2011 at 11:31 PM.
01-05-2011, 12:31 PM
#361
Registered
Join Date: Dec 2010
Location: Georgetown, KY
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
have an 04 also, bought an already used switchblade key from ebay for 20 bucks i programmed the remote part as per the first page worked first time, unfortunately i only received one key when i bought the car (craigslist) so now i have to go to the dealer to get a blank and have it cut and programmed. but the instructions worked !!! great thread.
01-26-2011, 08:24 AM
#363
Registered User
Join Date: Jan 2011
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
i have tried using the flow chart and i get to the part where the doors lock on there own after pressing the door switch 3 times . then i press the remote and nithing. I have tried several times thinking that the remote worked on a rolling code and would maybe take a while to match with the car but still no joy. I have tested that there is a signal coming from both of my remotes , they are both fine. Although can't say what the signal is. My remotes are visteon model No 41844 , do you or anyone else have any clues whats going on . I thought the battery had died because it stopped working all of a sudden but changing had no effect
01-26-2011, 05:57 PM
#364
Registered
Join Date: Aug 2008
Location: Massachusetts
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
i have tried using the flow chart and i get to the part where the doors lock on there own after pressing the door switch 3 times . then i press the remote and nithing. I have tried several times thinking that the remote worked on a rolling code and would maybe take a while to match with the car but still no joy. I have tested that there is a signal coming from both of my remotes , they are both fine. Although can't say what the signal is. My remotes are visteon model No 41844 , do you or anyone else have any clues whats going on . I thought the battery had died because it stopped working all of a sudden but changing had no effect
02-28-2011, 06:48 PM
#366
Just got my switchblade today...
totally works on my 2004 MT...
unit i bough on ebay:
FCC ID: KPU41788
IC : 4238A-41525
VISTEON 41525
i just followed this instructions: (few modification to be more NOOB friendly like me)
Remote Programming
• Ensure that all doors, trunk, and hood are closed,
• open the driver’s door
Carry out the operation below within 24 seconds:
• Insert key
• Turn ignition to the run position and off, 3 times (on-off, on-off, on-off)
• Leave key in ignition (off position, not lock or on)
• Push door switch, 3 times (The door switch is the little rubber one on the jamb of the rear door next to your elbow when sitting in the driver’s seat, which controls the interior lights.)
• Car will lock, then unlock automatically after pressing the door switch 3 times
• While the car is in unlock mode, Push 'Lock' on your newly acquired remote 2 times, (some suggest unlock, so try both)
• You will notice after pressing the Lock button on your remote, Car will lock, then unlock automatically again.
• Take out you key on the ignition and test your remote.
If it doesn't work, wait for a minute or so and repeat the procedure
NOTE: I DONT HAVE any existing remote. so no need to have an existing remote to do this procedure
One question though, i notice on most Rx8, when pressing the lock button on the remote the horn will honk, but mine doesn't have... anything i missed?
totally works on my 2004 MT...
unit i bough on ebay:
FCC ID: KPU41788
IC : 4238A-41525
VISTEON 41525
i just followed this instructions: (few modification to be more NOOB friendly like me)
Remote Programming
• Ensure that all doors, trunk, and hood are closed,
• open the driver’s door
Carry out the operation below within 24 seconds:
• Insert key
• Turn ignition to the run position and off, 3 times (on-off, on-off, on-off)
• Leave key in ignition (off position, not lock or on)
• Push door switch, 3 times (The door switch is the little rubber one on the jamb of the rear door next to your elbow when sitting in the driver’s seat, which controls the interior lights.)
• Car will lock, then unlock automatically after pressing the door switch 3 times
• While the car is in unlock mode, Push 'Lock' on your newly acquired remote 2 times, (some suggest unlock, so try both)
• You will notice after pressing the Lock button on your remote, Car will lock, then unlock automatically again.
• Take out you key on the ignition and test your remote.
If it doesn't work, wait for a minute or so and repeat the procedure
NOTE: I DONT HAVE any existing remote. so no need to have an existing remote to do this procedure
One question though, i notice on most Rx8, when pressing the lock button on the remote the horn will honk, but mine doesn't have... anything i missed?
02-28-2011, 11:53 PM
#368
you need AT LEAST 2 keys that are already cut/programmed (this can include the valet key) to program another key, after having it cut.
If you don't have 2 keys already that will unlock/start the car you will have to get the new key cut (anywhere can cut the key so it unlocks the door) AND you will have to get it programmed so it will start the car. You can get the programming done at a dealership or at select locksmiths.
Once you have those 2 programmed you can program another.
If your FOB goes bad you don't need any working ones to program the new one. All you need is ONE functioning key (fully functioning, unlocks and starts car). Use that key and follow the procedure to program the FOB.
If you have an '04 you CAN buy the switchblade FOB with FCC ID: KPU41788. It will program correctly.
03-01-2011, 12:02 AM
#369
U.S Army
iTrader: (6)
Join Date: Jun 2010
Location: Ohio
Posts: 210
Likes: 0
Received 0 Likes
on
0 Posts
Ok thanks Lord ET, I have 2 programed keys and the FOB im talking about is the switch blade. So i'm assuming theirs another set of instructions i have to follow so i can start the car with it. Ok thank you, i didn't read all the right parts.
03-08-2011, 06:52 PM
#370
I like roast duck
Join Date: Dec 2007
Location: Bay area
Posts: 316
Likes: 0
Received 0 Likes
on
0 Posts
my 04 remote went out. about to buy the switch blade. and i will have to do both the key encoding and the programing on the remote. since im getting a new uncut key. hope this will work.
Question: after click 3 times the door switch, i will click the "lock" button on the remote while is in the ignition correct?
Question: after click 3 times the door switch, i will click the "lock" button on the remote while is in the ignition correct?
03-08-2011, 09:55 PM
#371
my 04 remote went out. about to buy the switch blade. and i will have to do both the key encoding and the programing on the remote. since im getting a new uncut key. hope this will work.
Question: after click 3 times the door switch, i will click the "lock" button on the remote while is in the ignition correct?
Question: after click 3 times the door switch, i will click the "lock" button on the remote while is in the ignition correct?
Addendum:
After two years without a working FOB, I finally bought a used set from eBay for $20.
Received it and programmed both in seconds.
Last edited by Grace_Excel; 05-08-2016 at 03:55 AM. Reason: Added a picture
03-11-2011, 09:42 AM
#375
So i just recently bought an 04 used from someone, and they only gave me 1 key and 1 remote
i've been wanting to switch out to the switchblade one and in order for me to do so I would have to go to the dealer to get it reprogrammed with their machine
my question is, could i go buy another switch blade after that and reprogram the new 3rd switchblade using the mazda newly reprogrammed key and my old 04 key?
i've been hearing that the ecu picks up a different frequency and all that stuff
all the mazda dealerships around here in canada charge 50$ to program a key and 50$ to program the fob which is disgusting
i've been wanting to switch out to the switchblade one and in order for me to do so I would have to go to the dealer to get it reprogrammed with their machine
my question is, could i go buy another switch blade after that and reprogram the new 3rd switchblade using the mazda newly reprogrammed key and my old 04 key?
i've been hearing that the ecu picks up a different frequency and all that stuff
all the mazda dealerships around here in canada charge 50$ to program a key and 50$ to program the fob which is disgusting