DIY: Code your own key / remote
#151
the enemy in the mirror
Join Date: Oct 2006
Location: billerica, ma
Posts: 440
Likes: 0
Received 0 Likes
on
0 Posts
well the blade profile would have to match (be compatible) between both cars and the odds of that are small. but you very likely could program the transponder code into the rx-8.
#152
Hi there,
I ve tried to program the key and it was unsuccesful.
I ve used my 2 originals and then the new cutted key but the security icon blinks.
What am i doing wrong?
I ve tried to program the key and it was unsuccesful.
I ve used my 2 originals and then the new cutted key but the security icon blinks.
What am i doing wrong?
#154
hi takashi,
i ve just called them and they told me that the ECU is locked and they should first unlock it there and then follow this process.
they will charge me $70 for just programming, no cut no key.
but anyway they sell this key for $350 (ripoff) so for Cyprus standards, its still very cheap. I ve bought it for $60 shipped. lets see in 5 hours, i will keep you updated.
i ve just called them and they told me that the ECU is locked and they should first unlock it there and then follow this process.
they will charge me $70 for just programming, no cut no key.
but anyway they sell this key for $350 (ripoff) so for Cyprus standards, its still very cheap. I ve bought it for $60 shipped. lets see in 5 hours, i will keep you updated.
#155
ok, i brought the remote and they programmed it succesfully but the KEY is still not working. They told me that the ve faced problems with US-Spec keys and J-Spec cars. They will charge me $115 for programming of remote + new key, cut and programming.
I can get it from japanparts for $80 but i will still have to pay them for programming $70 which is $150. I guess i ll have to pay them $115.
P.S. I ve seen them doing something with an OBD tool so i guess they did lie about unlocking ECU's immobilizer for key registration procedure.
I can get it from japanparts for $80 but i will still have to pay them for programming $70 which is $150. I guess i ll have to pay them $115.
P.S. I ve seen them doing something with an OBD tool so i guess they did lie about unlocking ECU's immobilizer for key registration procedure.
Last edited by titaniumgr3y; 09-04-2007 at 09:55 AM.
#157
Registered User
Join Date: Feb 2007
Location: Sydney Australia
Posts: 281
Likes: 0
Received 0 Likes
on
0 Posts
ive just tried programming a new remote but with no luck. i followed all the steps, but as i hit the door switch (to get out of the 'programming mode') the doors lock and unlock twice and the remote doesnt work. Can anyone help me?
#158
ok, i went to the dealer today to receive my new key and its working now
for all JDM owners: our ecu is locked and we are not allowed to program more keys unless they unlock the ecu from the dealer. i can program keys now but not the US-Spec keys. US-Spec remote works perfectly.
for all JDM owners: our ecu is locked and we are not allowed to program more keys unless they unlock the ecu from the dealer. i can program keys now but not the US-Spec keys. US-Spec remote works perfectly.
#161
All,
Just wanted to share this little jem of how I got a cool new key for my 04 RX for 20.00!!! I bought a USED remote with Key on Ebay from someone who had an extra, then I used a lockout key that was with my car when I bought it to MAKE a key that worked in the ignition.
Here are pictures:
I bought the remote and removed the pin holding the (not mine) key from the fob.
I then took the lockout key (key that works in a doorlock, but not in the ignition, cause there is no chip in it) I taped it to the (not my car) key and I drilled a hole in it for the pin I took out and I cut the end you normally hold on to to match the one I removed(not my car).
I then replaced the key (my lockout key) into the key fob (the cool flip one), put the pin back in, followed the instructions on programming the remote and the extra key that are EVERYWHERE on the forum and VIOLA!!!!!
for 20.00 and about an hour of my time from old key to new cool one, I have a new RX8 cool flip key.
Just wanted to share this little jem of how I got a cool new key for my 04 RX for 20.00!!! I bought a USED remote with Key on Ebay from someone who had an extra, then I used a lockout key that was with my car when I bought it to MAKE a key that worked in the ignition.
Here are pictures:
I bought the remote and removed the pin holding the (not mine) key from the fob.
I then took the lockout key (key that works in a doorlock, but not in the ignition, cause there is no chip in it) I taped it to the (not my car) key and I drilled a hole in it for the pin I took out and I cut the end you normally hold on to to match the one I removed(not my car).
I then replaced the key (my lockout key) into the key fob (the cool flip one), put the pin back in, followed the instructions on programming the remote and the extra key that are EVERYWHERE on the forum and VIOLA!!!!!
for 20.00 and about an hour of my time from old key to new cool one, I have a new RX8 cool flip key.
![Smilie](https://www.rx8club.com/images/smilies/smile.gif)
Last edited by ModestoRX8; 10-07-2007 at 01:20 AM. Reason: Added Pictures
#162
More pics
More pics of the project.
There is a slight brass color at the base of the key where I did some cutting, but it is not noticable unless you stare at the thing and it was WAAAAAY cheaper than the hundreds of $$ people have been paying for this key.
Hope this helps some folks. I did all this with a table vice, some duct tape and a dremmel tool....
There is a slight brass color at the base of the key where I did some cutting, but it is not noticable unless you stare at the thing and it was WAAAAAY cheaper than the hundreds of $$ people have been paying for this key.
Hope this helps some folks. I did all this with a table vice, some duct tape and a dremmel tool....
#163
Registered User
Join Date: Oct 2003
Location: New Jersey
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
help!
thanks Modesto for getting me into the switch blade upgrade and its working.
I have a question for all. On the switch blade which button is for the trunk release/open?
thanks
I have a question for all. On the switch blade which button is for the trunk release/open?
thanks
#164
Jake's RX-8
Join Date: Apr 2007
Location: Lorton, VA - NOVA
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
It is a button(w/ Trunk Pic) right beside to caution - Red Button
Just press and hold it for about 1-2 secs to open it.
To close, you gotta close the trunk manually - Hand
Just press and hold it for about 1-2 secs to open it.
To close, you gotta close the trunk manually - Hand
#165
Registered User
Join Date: Oct 2003
Location: New Jersey
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
very strange ,Mine does not have the trunk button. it has a bigger panic button that takes up the space of the trunk button-comparing to the one posted 4 post up.
thanks for the reply
#166
Jake's RX-8
Join Date: Apr 2007
Location: Lorton, VA - NOVA
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
Hum............that's weird.
Hey, yours might be either Miata or SUV Remote.............
Double Check............Because all 8's remotes have a trunk button with picture.
Hey, yours might be either Miata or SUV Remote.............
Double Check............Because all 8's remotes have a trunk button with picture.
#168
Registered
iTrader: (1)
Join Date: Sep 2007
Location: Southeast NH
Posts: 349
Likes: 0
Received 0 Likes
on
0 Posts
Was able to program my key and remote on the switchblade with only 2 other keys (no existing remote.)
Just wanted to chime in that you do not need to have an existing remote to program a new one (as that does not seem to be the general opinion in this thread.)
Just wanted to chime in that you do not need to have an existing remote to program a new one (as that does not seem to be the general opinion in this thread.)
#173
Registered
iTrader: (1)
Join Date: Sep 2007
Location: Southeast NH
Posts: 349
Likes: 0
Received 0 Likes
on
0 Posts
At the Walmart I went to their key cutting machine was pretty much completely automated. The guy slid the key into a couple slots to figure out which setting to use, put the new and old keys all the way into 2 slots, clamped them down, lowered the safety shield and pressed the go button.
Seems like a monkey could do it. On the flip side, it's unlikely the best cutter in the world could do it well.
Seems like a monkey could do it. On the flip side, it's unlikely the best cutter in the world could do it well.
#175
you have to take it to the dealer if you are trying to get a smart key(credit card) the physical key work because you have the card in the car, won't work without card being in car. You have to access the PATS function in the cars pcm. Even then you have to log into mazda to get the IN CODE to gain access. Better have your mazda dealer do it and supply the key too.