Notices
Series I Do It Yourself Forum Wanna save some coin or time/money in the shop? Read up on Do-It-Yourself custom mods and repairs & post your own here.

DIY: De-Flood procedure - more flooding for this guy!!!

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old 01-27-2008 | 08:44 PM
  #1  
rreign's Avatar
Thread Starter
I do what I want
 
Joined: Sep 2007
Posts: 75
Likes: 0
From: S.C.
Thumbs up DIY: De-Flood procedure - more flooding for this guy!!!

I just wanted to say there was about 3 weeks that went by that my 8 sat in the garage. I tried everything...battery,ignition coils,wires,spark plugs, etc. I jumped on here and found a million problem solving techniques on flooding. To be honest, I guess most probably would have worked, but I tried a few that were just not gettin the job done Then I came across one by NYWoody that worked perfectly.
I don't want to steal the thunder but I did want to re-post so that everyone that has tried just about everything could stop here at this post. This is definitly for a severely flooded engine.

So kinda like NYWoody said (but with my own twist).... get yourself some good music, a 13/16 sparkplug socket a rag and maybe a stiff drink, this could be awhile!

(Be sure your engine is flooded before having to go through this!!)

1. Remove the Fuel Relay Fuse, the Circuit Fuse and the Fuel Pump Fuse.
(the circuit and fuel relay can be found in the fuse box under the hood at the very bottom left hand corner.)

2. Jack up the front left side of the car, remove the front left tire (it's easier to get to the plugs that way) and remove the plugs.

3. Spend some time cleaning the plugs very thoroughly ( I used an old tooth brush and some brake free) and make sure to completely dry them off when your done. Be extremely carefull not to brake them (they're about $30 a piece)

4. Here comes the fun part... Get in the car (music blairing in your ears of course) press the accelerator all the way down and turn the key to "ON" Now try and start the car for about 5-7 sec. Keeping the Gas to the floor, wait about 20-30 seconds and try to start the car again. Repeat this process for about 10 maybe 15 minutes. (Or about 3 songs)

5. Now get out of the car and check the holes from the spark plugs. You will have to clean all of the gas and oil from inside and around the holes to make sure you get a good clean area.

You will have to repeat steps 4 and 5 a few times until you have no more excess gas and oil coming out of the holes.

6. Put the spark plugs back in, the wires over the spark plugs and all fuses back in. Turn the car to the "ON" position and leave it there for about a minute or so. This ensures the fuel pump and everything has been "primed" Now simply try to start the car normally. You may have to give it a little gas to keep it running.

If your car starts then dies again, you may have to repeat steps 3 thru 5 all over again. But keep at it. Im sure if your engine is flooded, this process works. It took me about 2 hours, but it was all worth it!!
Old 01-27-2008 | 08:48 PM
  #2  
BlueRenesis82's Avatar
Registered Tracker
 
Joined: Feb 2004
Posts: 3,295
Likes: 0
From: Chicago
Wow, thanks! I am sure none of this information is available on our website using the search button!
Old 01-27-2008 | 09:19 PM
  #3  
dannobre's Avatar
Modulated Moderator
iTrader: (3)
 
Joined: Feb 2004
Posts: 13,719
Likes: 338
From: Smallville
Towing it for half a block is a lot easier

( unless you have an auto )
Old 01-27-2008 | 09:20 PM
  #4  
Mazurfer's Avatar
Surf Hard, Drive Hard
 
Joined: Feb 2007
Posts: 7,840
Likes: 12
From: Indialantic, Florida
How did it get flooded in the first place..............that's what I want to know.
Old 01-27-2008 | 09:59 PM
  #5  
AndrewE's Avatar
Yellow Fever
 
Joined: Mar 2007
Posts: 148
Likes: 1
From: Lanark, ON
I found all that crap to be a waste of time

just made sure battery was good, jumper car hooked up and just rolled it over for 8 second intervals with my foot floored on the gas pedal with 20 second breaks for the starter to cool, 8th try lifted my foot and it ran
The following users liked this post:
Sam baldauff (05-13-2021)
Old 01-27-2008 | 11:38 PM
  #6  
dannobre's Avatar
Modulated Moderator
iTrader: (3)
 
Joined: Feb 2004
Posts: 13,719
Likes: 338
From: Smallville
Originally Posted by AndrewE
I found all that crap to be a waste of time

just made sure battery was good, jumper car hooked up and just rolled it over for 8 second intervals with my foot floored on the gas pedal with 20 second breaks for the starter to cool, 8th try lifted my foot and it ran
Good luck if you really flood it......You will cook your starter long before the wet/fouled plugs will start.
Old 01-28-2008 | 05:46 PM
  #7  
rreign's Avatar
Thread Starter
I do what I want
 
Joined: Sep 2007
Posts: 75
Likes: 0
From: S.C.
Well i freakin pulled the car out of a parking space at the hospital and drove it closer to my wifes car so i could put some stuff in it when she was having our baby. I wasnt really thinking, without letting it warm up i just shut it off. Had to tow it back to the house where the fun began. My starter seems fine, although this method will take some miles off it ya know?! I tried a lot of other things like what was mentioned and I couldn't get anything else but this to work.
Old 01-29-2008 | 02:19 AM
  #8  
Startl_Respons's Avatar
Banned
 
Joined: Oct 2003
Posts: 286
Likes: 0
From: the hive
Uh hello? Did you read my thread, which is very similar to what you did. However, you need to disconnect the eccentric shaft position sensor before the "purging" process. Also, when you're finally ready to try to start the engine, you should just press down on the accelerator (to prevent fuel injection) and crank for about 1 to 3 minutes. Then finally release the pedal and crank again. It will probably fire up or almost fire up immediately.
Old 01-29-2008 | 05:43 AM
  #9  
Yellow888's Avatar
Slow in, fast out
 
Joined: Mar 2005
Posts: 21
Likes: 0
From: N29.8903 W95.6684
This is the good one too from DIY Deflooding in under 5 mins



https://www.rx8club.com/showthread.php?t=55517.html
Old 01-29-2008 | 07:02 AM
  #10  
Startl_Respons's Avatar
Banned
 
Joined: Oct 2003
Posts: 286
Likes: 0
From: the hive
Originally Posted by Yellow888
This is the good one too from DIY Deflooding in under 5 mins



https://www.rx8club.com/showthread.php?t=55517.html
That is the DIY that you DON'T want to read. For people who have just flooded their car, do you think they want to go through all that? The first part of the stupid DIY is simply go do the Mazda deflooding procedure. Uh, thanks for telling me that.

That DIY should be retitled "How to get ready for future flooding"
Old 01-29-2008 | 08:33 PM
  #11  
Mazurfer's Avatar
Surf Hard, Drive Hard
 
Joined: Feb 2007
Posts: 7,840
Likes: 12
From: Indialantic, Florida
Hey, I didn't mean to ask the question with the intent of making you out to be an idiot or anything.
I've had mine for two years now and never flooded(Thank God) and don't want to ever have to go through this whole thing!
So........ I'm just merely compiling the data somewhere back in the dark resesses of my mind when I hear these flooded things, just so that I see the different situations where people cause it to happen.
The reality is that this shouldn't even be the case ya know? It kinda sucks in a big way that we have to deal with it....even though it's really not a big deal until you forget!
Old 01-30-2008 | 01:54 AM
  #12  
rx8 man's Avatar
Registered User
iTrader: (1)
 
Joined: May 2007
Posts: 112
Likes: 0
flooding

Originally Posted by rreign
I just wanted to say there was about 3 weeks that went by that my 8 sat in the garage. I tried everything...battery,ignition coils,wires,spark plugs, etc. I jumped on here and found a million problem solving techniques on flooding. To be honest, I guess most probably would have worked, but I tried a few that were just not gettin the job done Then I came across one by NYWoody that worked perfectly.
I don't want to steal the thunder but I did want to re-post so that everyone that has tried just about everything could stop here at this post. This is definitly for a severely flooded engine.

So kinda like NYWoody said (but with my own twist).... get yourself some good music, a 13/16 sparkplug socket a rag and maybe a stiff drink, this could be awhile!

(Be sure your engine is flooded before having to go through this!!)

1. Remove the Fuel Relay Fuse, the Circuit Fuse and the Fuel Pump Fuse.
(the circuit and fuel relay can be found in the fuse box under the hood at the very bottom left hand corner.)

2. Jack up the front left side of the car, remove the front left tire (it's easier to get to the plugs that way) and remove the plugs.

3. Spend some time cleaning the plugs very thoroughly ( I used an old tooth brush and some brake free) and make sure to completely dry them off when your done. Be extremely carefull not to brake them (they're about $30 a piece)

4. Here comes the fun part... Get in the car (music blairing in your ears of course) press the accelerator all the way down and turn the key to "ON" Now try and start the car for about 5-7 sec. Keeping the Gas to the floor, wait about 20-30 seconds and try to start the car again. Repeat this process for about 10 maybe 15 minutes. (Or about 3 songs)

5. Now get out of the car and check the holes from the spark plugs. You will have to clean all of the gas and oil from inside and around the holes to make sure you get a good clean area.

You will have to repeat steps 4 and 5 a few times until you have no more excess gas and oil coming out of the holes.

6. Put the spark plugs back in, the wires over the spark plugs and all fuses back in. Turn the car to the "ON" position and leave it there for about a minute or so. This ensures the fuel pump and everything has been "primed" Now simply try to start the car normally. You may have to give it a little gas to keep it running.

If your car starts then dies again, you may have to repeat steps 3 thru 5 all over again. But keep at it. Im sure if your engine is flooded, this process works. It took me about 2 hours, but it was all worth it!!

This is basicly what I had to do with a old series 1 Rx7 I had about 10 years ago, pull the plugs, kill the fuel pump, turn motor over, refit clean plugs.
But the rx7 series one didn't have a flooding problem--- had oil control seal problems, was fine when hot, but if you let it sit and cool down eg 4/5 hours, out the with plugs .. etc..etc, haven't had to do this with my rx8.
My 2c worth
Old 05-08-2015 | 11:35 AM
  #13  
2009R3's Avatar
Registered
iTrader: (1)
 
Joined: Feb 2013
Posts: 23
Likes: 0
I just tried this and it worked for me

Originally Posted by AndrewE
I found all that crap to be a waste of time

just made sure battery was good, jumper car hooked up and just rolled it over for 8 second intervals with my foot floored on the gas pedal with 20 second breaks for the starter to cool, 8th try lifted my foot and it ran
Thank you for this. This morning I went to start my 8 for the first time since Novemeber!
I've never experienced a flooding issue, partly because I am always very careful to let the car warm up before I shut it down, and partly because I'm sure because it's a S2...but regardless the reason when I went to start it, it sputtered and shut down and would not restart.
I had great starter and battery performance so I decided to try the above approach. After the 2nd try with the gas pedal down and starter going for 8sec. there were signs of life so I kept on trying, and just like it said, around the 7-8th attempt I had a full restart.

The exhuast was cloudy with a slightly blue colour (incompletely burned fuel I imagine), but quickly cleared up.
I have my 8 idling in the garage now and all seems to be okay.
Old 09-22-2016 | 03:30 PM
  #14  
Vaibhav's Avatar
New Member
 
Joined: Sep 2016
Posts: 2
Likes: 0
TX Engine won't start.

Guys yesterday I was driving my car on a highway, and engine suddenly stopped, it was my luck that it stopped at near a shoulder. So I pushed it there. There was smoke from the hood, from the coolant container. I waited for some time for it to cool down and then I poured some coolant, and also it had very small amount of engine oil, so I poured around 5 quarts of it as well. Then I tried to start it, it was not starting as the battery was also dead, then toll road assistance came there and the guy gave my car a jump start, it was cranking but the engine was not starting, and as I pressed the gas after a while of charging my battery, it started but the silencer was smoking really bad as I was pressing gas. And it turned of, every time to start it I had to charge the battery for a while and again same things happened. Can someone help me in guessing the problem.
Old 09-22-2016 | 07:33 PM
  #15  
BigCajun's Avatar
Banned
iTrader: (1)
 
Joined: Jan 2013
Posts: 6,164
Likes: 2,697
Flooding doesn't suddenly happen when driving.
Old 05-13-2021 | 04:57 PM
  #16  
Sam baldauff's Avatar
New Member
 
Joined: Jan 2021
Posts: 5
Likes: 0
Way easier

Originally Posted by AndrewE
I found all that crap to be a waste of time

just made sure battery was good, jumper car hooked up and just rolled it over for 8 second intervals with my foot floored on the gas pedal with 20 second breaks for the starter to cool, 8th try lifted my foot and it ran
i just had the problem. Did his methods. It worked great. Thanks bro took 5-10 mins
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
gwailo
New Member Forum
38
05-14-2024 06:57 AM
Brooklynite
NE For Sale/Wanted
4
11-10-2015 06:42 PM
SBGarage
Sakebomb Garage
3
10-22-2015 04:28 PM
SBGarage
Group Buy Center
1
09-12-2015 08:18 PM
Slack
New Member Forum
6
09-05-2015 06:42 PM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: DIY: De-Flood procedure - more flooding for this guy!!!



All times are GMT -5. The time now is 02:25 PM.