DIY: Start Button, Front & Centre! - Page 2

02-09-2008 | 01:28 PM

#26

usafmannyg

Manny

Joined: Mar 2007

Posts: 6

Likes: 0

From: St. Louis

I need to know where you got these push start parts...

Can you give me the link where I can get the push button parts to install it in my ride...???

Reply Like

02-09-2008 | 01:33 PM

#27

luis_o_98

.

iTrader: (-1)

Joined: Nov 2007

Posts: 571

Likes: 0

ive seen them at autozone

Reply Like

02-09-2008 | 07:07 PM

#28

usafmannyg

Manny

Joined: Mar 2007

Posts: 6

Likes: 0

From: St. Louis

I went there and Advance, and Oreily's, I got nothin..

Reply Like

04-17-2008 | 05:24 AM

#29

bran702

Banned

Joined: Dec 2007

Posts: 59

Likes: 1

From: North Las

Ebay... Search Honda S2000 Push Start

Reply Like

03-09-2009 | 06:39 PM

#30

Blackout04RX

Need for Speed Satisfied

Joined: Mar 2008

Posts: 343

Likes: 0

From: Monroe, CT

I know this is an old thread, but I bought the S2000 switch, delivered today. I had two questions. When cutting into the blue/white wire, do I connect the signal from the switch on the side of the ignition? Also, how did you connect into the pins with the wires? Looks clean, curious how you managed that. My solder gun wont reach in there, and i can't see how just sticking it in and hoping it holds would be at all successful...

Reply Like

01-14-2011 | 02:11 AM

#31

StealthTL

Thread Starter

Metatron

iTrader: (1)

Joined: Mar 2003

Posts: 7,284

Likes: 175

From: A Pacific Island.

First post updated!
Button now only $10......

Attached Thumbnails

Reply Like

01-14-2011 | 10:05 AM

#32

Ross_Dawg

Registered Toker

iTrader: (2)

Joined: Dec 2007

Posts: 5,545

Likes: 1

From: Bend, OR

Damn, I might need to tinker with that now

Reply Like

01-14-2011 | 10:45 AM

#33

oltmann

Registered

Joined: Sep 2010

Posts: 531

Likes: 1

Uselessly answering blackout's question, a floppy disk power supply connector perfectly fits over four of the pins on the Honda button.

Reply Like

02-21-2012 | 11:40 AM

#34

Zeuscraig1

Registered User

Joined: Feb 2012

Posts: 8

Likes: 0

How do you take the small front plate off like the guy did to fit the starter button on the front of your radio. Mine doesn't want to budge. I don't want to put to much force and break it? I have scratched mine I need to replace to. Any ideas where I would get a replacement. It's a uk rhd 231 rx8 thx

Reply Like

02-21-2012 | 12:39 PM

#35

StealthTL

Thread Starter

Metatron

iTrader: (1)

Joined: Mar 2003

Posts: 7,284

Likes: 175

From: A Pacific Island.

The second post shows the clips on the back - a sharp screwdriver down the side and ease it out, three clips, pull straight out.

Both easy and peasy.

Reply Like

02-21-2012 | 12:50 PM

#36

Zeuscraig1

Registered User

Joined: Feb 2012

Posts: 8

Likes: 0

So as am looking AT my radio I put a screwdriver down the left side of the panel and pry it out. Thankyou but where can I get a new one? Laugh out loud without buying whole new radio

Reply Like

02-22-2012 | 08:38 AM

#37

Highspeed

2 Tone...Low Drone

iTrader: (2)

Joined: Dec 2010

Posts: 408

Likes: 0

From: Broken Arrow, OK

Stealth...can you post the link again for the start button for 10 bucks...AND...where would you wire the button in for an automatic since there is no clutch?

Reply Like

02-24-2012 | 11:02 AM

#38

Zeuscraig1

Registered User

Joined: Feb 2012

Posts: 8

Likes: 0

What color wire do I hijack from the ignition to the starter solenoid? I have to hook up two wires to
Two wires from ignitor to starter solenoid but dOnt know
Which color they are. Can anyone help. Onand am having trouble blood getting the cigerette lighter out it wont unclip. I got all plate out just need to get it out of the round hole so
I can put my starter buttOn in. Please help thankyou

Reply Like