Baseline Automated Tuning Beta Now Available for Download
#777
I just want to say that baseline is amazing!!!
THANKS KANE!!
THANKS KANE!!
#779
so my beta version ends tomorrow...It's a sad day for me
Thanks for the program Kane! Can't wait till the final product is released
Thanks for the program Kane! Can't wait till the final product is released
#785
it works fine but somehow I over shot my target a/f ratio by by a full point. I was tunning for 11.1 but repeatedly see 12.1-12.3. It might have something to do with the temp I put in while massaging the file? I didn't expect for things to run perfectly but I would hate to see that turn into a big problem when I up the boost. Right now I'm at 8psi. I might just take it to a tuner though in the next couple of months. I think I'm a little over my head here. Especially when I up the boost.
#786
put some crazy dragon graphics on that thing! The final product is looking good but I'm sure will have even more changes to it before release. Keep up the good work. Will the standalone allow me to upload my larger log files?
#788
fuel map
I atctually think this might be caused by user error. I cleared a code that I wasn't paying attention to yesterday and now my af/r looks right. Once the light comes back on I can check to see if that was the issue. I'm betting it is. I have to get a new TPS. It freaks out from time to time.
I atctually think this might be caused by user error. I cleared a code that I wasn't paying attention to yesterday and now my af/r looks right. Once the light comes back on I can check to see if that was the issue. I'm betting it is. I have to get a new TPS. It freaks out from time to time.
#794
SARX Legend
iTrader: (46)
![TX](https://www.rx8club.com/images/icons/tx.jpg)
Let me know, free is cool but I have helped develop software in the past so I know the amount of time and work it takes to get to the finished product. I have no problem donating to the cause.
#798
I am almost there...
I build engine, create injectors and MAF tables etc....
When I go to import log file from COBB ACCESS PORT, import is successful.
( I had changed the tiime in the access port log into ms as well as per instructions..)
When I go to "view selected cell" I get nothing in the "Fuel Map worksheet"
See attached screen shot. Always blank.
When I go to create new map, I get " You are going to tune 0 records in 0 min"
Tried everything???? Any ideas what I am doing wrong?
Running Windows 7 lenovo laptop, 32 bit. Office 2007 Ultimate.
Thanks.
When I go to import log file from COBB ACCESS PORT, import is successful.
( I had changed the tiime in the access port log into ms as well as per instructions..)
When I go to "view selected cell" I get nothing in the "Fuel Map worksheet"
See attached screen shot. Always blank.
When I go to create new map, I get " You are going to tune 0 records in 0 min"
Tried everything???? Any ideas what I am doing wrong?
Running Windows 7 lenovo laptop, 32 bit. Office 2007 Ultimate.
Thanks.
#800
Hey Kane... Thanks for getting back to me.
I used the MAF scale. I copied the same paramiters from ACCESSPORT Race software....
When I click on" View selected cell" it brings up a blank fuel map worksheet.
tblMAFScale subformMAFVoltsMAFgsec0.861.960.982.901.023.271.053.651.094.061.134.491.174.981.215.521.256.081.296.661.337.271.377.921.418.631.4810.121.5611.761.6413.511.7215.471.8017.701.8820.141.9522.822.0325.782.1129.052.1932.632.2736.652.3441.112.4245.962.5453.832.6662.412.7771.852.8982.213.0193.383.13105.333.24118.103.36131.563.48145.873.59161.163.71177.563.83195.153.94214.004.06234.204.18255.744.30278.634.41302.904.49319.864.57337.434.61346.474.65355.684.69365.06
I did populate PSI/Load by "LOAD", again took the values that are in ACCESSPORT race.
I did this because the access port logs by calculated load, not manifold PSI?
RPM Scale, took numbers from ACCESSPORT Race software.
When I click on "Auto Create Fuel Map" it of course tells me that I have 0 records....
I must be missing a step or sumth?
Thanks bud.
I used the MAF scale. I copied the same paramiters from ACCESSPORT Race software....
When I click on" View selected cell" it brings up a blank fuel map worksheet.
tblMAFScale subformMAFVoltsMAFgsec0.861.960.982.901.023.271.053.651.094.061.134.491.174.981.215.521.256.081.296.661.337.271.377.921.418.631.4810.121.5611.761.6413.511.7215.471.8017.701.8820.141.9522.822.0325.782.1129.052.1932.632.2736.652.3441.112.4245.962.5453.832.6662.412.7771.852.8982.213.0193.383.13105.333.24118.103.36131.563.48145.873.59161.163.71177.563.83195.153.94214.004.06234.204.18255.744.30278.634.41302.904.49319.864.57337.434.61346.474.65355.684.69365.06
I did populate PSI/Load by "LOAD", again took the values that are in ACCESSPORT race.
I did this because the access port logs by calculated load, not manifold PSI?
RPM Scale, took numbers from ACCESSPORT Race software.
When I click on "Auto Create Fuel Map" it of course tells me that I have 0 records....
I must be missing a step or sumth?
Thanks bud.