Greddy EMU upgrade kit or EMU?
#26
Finally Boosted!!!!!!!
Phish - I don't know anyone who has purchased greddy's plug and play RX8 harness (MA-11). Where are you looking to get it from? Also, is your car an MT or AT?
The universal Ultimate (version E) should work just fine for the RX8. You will need to set the jumpers appropriatly but that is not hard.
Yes, you will need the A/F harness to connect a wideband.
Sounds like you have planned this and done your research. Good Job!
The universal Ultimate (version E) should work just fine for the RX8. You will need to set the jumpers appropriatly but that is not hard.
Yes, you will need the A/F harness to connect a wideband.
Sounds like you have planned this and done your research. Good Job!
#28
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
i have a MT and alot more research to do . i have not looked into where to purchase yet as far as price or anything goes. thats what i plan on doing hte next couple of days. alot of my research will be on tuning and how to do so and where to get started. i might just try and find someone close to IA to give me a crash course
#29
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
The cheapest i have found the MA-11 Harness is 160.00. This is 40.00 cheaper then the Greddy price.
http://www.turbochargers.com/store/p...ab190ef41fed2d
Also, i believe that i will most likely purchase the EMU and A/F harness from this sight.
http://www.mohdparts.com/emanage/#E-manage%20Ultimate:
http://www.turbochargers.com/store/p...ab190ef41fed2d
Also, i believe that i will most likely purchase the EMU and A/F harness from this sight.
http://www.mohdparts.com/emanage/#E-manage%20Ultimate:
Last edited by Phish806; 01-22-2008 at 11:38 AM.
#31
Finally Boosted!!!!!!!
The cheapest i have found the MA-11 Harness is 160.00. This is 40.00 cheaper then the Greddy price.
http://www.turbochargers.com/store/p...ab190ef41fed2d
http://www.turbochargers.com/store/p...ab190ef41fed2d
Also, i believe that i will most likely purchase the EMU and A/F harness from this sight.
http://www.mohdparts.com/emanage/#E-manage%20Ultimate:
http://www.mohdparts.com/emanage/#E-manage%20Ultimate:
#32
Finally Boosted!!!!!!!
#34
Finally Boosted!!!!!!!
Thats one of my issues. I dont' know the part number for the dongle that I have. MazdaManiac might know? I have never asked him. It's not listed on Greddy's or Mohd's website, either.
#35
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
could be a stupid question and i know that you have already thought of this ... but whouldnt there be a part number printed on the one you have installed or in one of the installation manuals?
#36
Finally Boosted!!!!!!!
Nope, here is a picture of it. Its an O2 Adapter.
http://www.mohdparts.com/emanage/rx8...e/DSC09506.JPG
http://www.mohdparts.com/emanage/rx8...e/DSC09506.JPG
#37
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
as far as the picture onthe sight goes it is a generic pic, all the pictures for the differnt PnP harnesses are the same picture. so the 8 harness might contain the dongule. i will find an email address and see if i can get a reply
#38
Finally Boosted!!!!!!!
It would be awesome if turbochargers.com had the correct harness. Then you could get the Ultimate (Version E), the A/F harness, the EManage Ultimate Harness Kit, and the Ignition Chip #2 from Mohd. That should be everything. All you would need to do is rewire it...
#41
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
the ignition adapter is not pictured in the pic on the turbochargers.com sight either. so i am hoping that it will contain the ignition adapter and the dongule and i would only have to purchase the A/F harness seperate. i emailed them and i will let you know when i get a responce. also ... what exactly woudl i have to rewire and for what purpose. i am not clear on this part as far as what gets wired and for what reason... like i said .. still doin research
#42
Finally Boosted!!!!!!!
You will need to read the Installation Manual, the Operation Manual, and this thread to understand how to set the jumpers and how to wire everything.
While Greddy says its PnP, their solution doesn't give you the full functionality of the Ultimate. By rewiring it like MazdaManiac and I have you have full functionality.
While Greddy says its PnP, their solution doesn't give you the full functionality of the Ultimate. By rewiring it like MazdaManiac and I have you have full functionality.
#43
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
From the thread that you listed i know what the jumper settings shouldbe set at, but i am still kind of confused on what needs to be rewired if i am not FI. could you point me twords a specific post or section that woudl explain what needs to be done just for the N/A guys. Not trying to be a pain by the way ... just gets that way sometime
#44
Finally Boosted!!!!!!!
The wiring for N/A should be the same as the wiring for FI in this case. Thats why we rewired it. Greddy origionally wired the injectors for Add Only. For N/A you will want to trim fuel. But you cant do this unless you rewire it and change the jumpers.
#45
Banned
iTrader: (3)
The dongle is not available as a separate part and the upgrade kit appears to be no longer in the retail channel.
I will be making a MM version of the O2 dongle available for purchase in the very near future.
The only other part needed is the #2 ignition adapter.
I buy all of my GReddy stuff from Mohd.
He is very good, respectable and fairly local for me (he is in Tucson).
I will be making a MM version of the O2 dongle available for purchase in the very near future.
The only other part needed is the #2 ignition adapter.
I buy all of my GReddy stuff from Mohd.
He is very good, respectable and fairly local for me (he is in Tucson).
#46
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
So MM's Post #39 is how everythign should be set up? The jumpers set as listed in the first part, and the wiring changes made as stated in the rest of the post. For N/A and for FI thats the finnished product? jsut trying to verify
#48
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
https://www.rx8club.com/series-i-engine-tuning-forum-63/emanage-ultimate-turbo-upgrade-kit-findings-96973/page2/
and i plan on purchasing the MA-11 harness along with the A/F harness as well ...
and i plan on purchasing the MA-11 harness along with the A/F harness as well ...
#49
Registered
iTrader: (4)
Join Date: Jul 2007
Location: Des Moines, Ia
Posts: 950
Likes: 0
Received 0 Likes
on
0 Posts
Ok, so i received the harness today. I am still waiting on the actual emanage to show up. It has already been shipped out though so now i am jsut waiting on UPS. The harness came with the Ignition chip but no dongle. Now is it just a matter of searching the boards for someone that has one and wants to sell, Or maybe one of you guys have an extra one laying around, or MM might have his own version....? Also .. since i do not have the dongle, what would happen if i did not install it. I know if forces open loop but doesnt the emanage have to do that at some point anyway to make the changes?.. The dongle just force open loop sooner so you can adjust at a lower rpm?... if i installed the ignition chip and set the jumper settings correctly without rewiring (cuz of not having the dongle) what would the major differences be as opposed to rewiring it?