Possible Problem?
#26
Not so Super right now
Thread Starter
Join Date: May 2003
Location: Beyond that there swamp.
Posts: 1,493
Likes: 0
Received 0 Likes
on
0 Posts
I havent run an engine cover for the past 3 or 4 months, so that wasnt it in my case. I think it was just my coils where gonna go eventually. I doubt the stage1 casued anyting, unless one of the components on the extra circuit for the ignition control is bad or defective. Maurice will test that out to make sure it's OK or not as the case may be.
#27
Registered User
Join Date: Jul 2003
Location: Edmonton
Posts: 680
Likes: 0
Received 0 Likes
on
0 Posts
Better put your engine cover back on. It's supposed to improve air flow under the hood. Directs it out the side vents, I'm told.
Worst case for high underhood temps - high load slow speed - such as autocross. High speed will not heat it up as there is lots of natural airflow at high speeds. Pull off a highway and drive slowly up a steep hill - that'll heat it up! Heat soak is caused by the engine operating heat normally removed by the cooling system staying in the engine because you came off the expressway and stopped the engine without letting it cool down for a few minutes. Check out cars parked in rest stops on highways. You'll find at least one in twenty has boiled out a bit of coolant.
Of course none of this will damage the coils if the engine is shut off.
Worst case for high underhood temps - high load slow speed - such as autocross. High speed will not heat it up as there is lots of natural airflow at high speeds. Pull off a highway and drive slowly up a steep hill - that'll heat it up! Heat soak is caused by the engine operating heat normally removed by the cooling system staying in the engine because you came off the expressway and stopped the engine without letting it cool down for a few minutes. Check out cars parked in rest stops on highways. You'll find at least one in twenty has boiled out a bit of coolant.
Of course none of this will damage the coils if the engine is shut off.
#28
Bebop driver
Join Date: Sep 2003
Location: Alexandria, VA
Posts: 280
Likes: 0
Received 0 Likes
on
0 Posts
Thanks. But now I'm tempted: "So, officer, I HAD to take my front plate off to improve air flow. Yes, I'll put it back on in less stressful driving conditions. You don't give a WHAT?"
#29
Registered User
Join Date: Mar 2004
Location: Austin Texas
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by RX-8 friend
I think there are two potential problems with this setup (no pun intended
. Unlike most current logic chips, the voltage that the PCM puts out goes from 0V to +5V. Most logic puts out +1.4V or so when "OFF" to +4.4V or so when "ON". This is what our box puts out, so we had to add a series diode to the ignition output of our unit, as 1.4V will keep the transistor somewhat on and heat it up. That is what happened to Maurice's coil packs and Maniacs as well. The diode drops the voltage by 1V or so. The transistor doesn't start to conduct until the base voltage reaches 0.7V or so. Problem one solved.
I think there are two potential problems with this setup (no pun intended
![Wink](https://www.rx8club.com/images/smilies/wink.gif)
Or maybe just a second diode?
#30
Registered User
Join Date: Jul 2003
Location: Edmonton
Posts: 680
Likes: 0
Received 0 Likes
on
0 Posts
No, common misconception - a single diode will drop 0.7V with very low current (about 1mA or less). Check out a data sheet. Under normal operating current you will find about 1V drop. Measured it. Got about 1V. Tried two diodes, got a 2V drop and started having problems with Maurice's car (which causes me to think it's not saturating the transistor when "ON"). Switched back to one diode, problem solved. We looked at "digital transistors" too. Unfortunalty they invert the output so you need two. They take the output down to about 0.2V. Parts count went way up (regulator needed as well as the two devices plus some resistors). More parts to fail. If we can't make the diode reliable we may have to go that route, but current indications are one diode will be fine, in fact better than stock, as the electronics we are using can drive more current than the stock PCM.
Now, in truth the current units that have been shipped also had a resistor to ground to lower the drive current. We thought being closer to stock values was better. I now think those resistors should be removed (two 2K2 resistors on end of board - they can just be cut of - leave the 10K resistors alone - they are part of the tach output). This is on the small PCB beside the Main unit. Just incase any of you want to experiment.
As I said, more measurements will be done soon (with a heat gun and scopemeter).
Now, in truth the current units that have been shipped also had a resistor to ground to lower the drive current. We thought being closer to stock values was better. I now think those resistors should be removed (two 2K2 resistors on end of board - they can just be cut of - leave the 10K resistors alone - they are part of the tach output). This is on the small PCB beside the Main unit. Just incase any of you want to experiment.
As I said, more measurements will be done soon (with a heat gun and scopemeter).
Last edited by RX-8 friend; 05-11-2004 at 09:58 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Shankapotamus3
Series I Trouble Shooting
28
03-14-2021 03:53 PM
tommy26Germany
Series I Trouble Shooting
11
09-29-2015 10:33 AM