Fender Vent DIY
09-18-2006 | 08:29 PM
#1
Fender Vent DIY
After staring at a foreign language for a couple hours I stumbled across a really good DIY mod. Figured I should share...
(Direct translation from babelfish adds a little comedy)
It is processing the fender grille.
Grille under photograph to grille above
It keeps cutting with the cutter knife.
Patience needs suitable, (the ^^)
Way the finger is not flown,!
(Paying attention on self responsibility.)
The part, with left and right, is about 1500 Yen.
With such feeling, the ちび ちび cutting
It goes.
If there is a compressor, with the air saw
It can make easy, however it is, don't you think? the ぇ.
Furthermore, it finishes to here.
Before painting, already just a little it is to be cut off, does.
Temporarily, time it is required.
Headache may do,
When it paints, such feeling?
Already, just a little, the finish is bad, don't you think? is.
The mark of the paper coming out, it increases.
(Also the photograph is bad, is.)
It is halfway lapse.
Because there are left and right, it is serious.
After, of the net is not thought, as for the て.
When you complete, such feeling
Paper in 400．600．1000 turn
Applying correcting, re-paint
Brilliant black for ホルツマツダ car
As for wire net, at foam/home center,
One for screen door of 10 cm 100 Yen
Net of aluminum
The reverse side, turning back,
Stopping at the hot bond
Completion!
When you install, it becomes such feeling.
Because the inside, is completely visible, unless it paints in black, (the ^ ^)
(Direct translation from babelfish adds a little comedy)
It is processing the fender grille.
Grille under photograph to grille above
It keeps cutting with the cutter knife.
Patience needs suitable, (the ^^)
Way the finger is not flown,!
(Paying attention on self responsibility.)
The part, with left and right, is about 1500 Yen.
With such feeling, the ちび ちび cutting
It goes.
If there is a compressor, with the air saw
It can make easy, however it is, don't you think? the ぇ.
Furthermore, it finishes to here.
Before painting, already just a little it is to be cut off, does.
Temporarily, time it is required.
Headache may do,
When it paints, such feeling?
Already, just a little, the finish is bad, don't you think? is.
The mark of the paper coming out, it increases.
(Also the photograph is bad, is.)
It is halfway lapse.
Because there are left and right, it is serious.
After, of the net is not thought, as for the て.
When you complete, such feeling
Paper in 400．600．1000 turn
Applying correcting, re-paint
Brilliant black for ホルツマツダ car
As for wire net, at foam/home center,
One for screen door of 10 cm 100 Yen
Net of aluminum
The reverse side, turning back,
Stopping at the hot bond
Completion!
When you install, it becomes such feeling.
Because the inside, is completely visible, unless it paints in black, (the ^ ^)
09-18-2006 | 10:35 PM
#8
jersey fresh
Joined: Dec 2005
Posts: 3,688
Likes: 0
From: Boston, MA
Fixed!
Grille under photograph to grille above
It keeps cutting with the cutter knife.
Patience needs suitable, (the ^^)
Way the finger is not flown,!
(Paying attention on self responsibility.)
{not to sure}
The part, with left and right, is about 1500 Yen.
With such feeling, the ちび ちび cutting
It goes.
If there is a compressor, with the air saw
It can make easy, however it is, don't you think? the ぇ.
It keeps cutting with the cutter knife.
Patience needs suitable, (the ^^)
Way the finger is not flown,!
(Paying attention on self responsibility.)
{not to sure}
The part, with left and right, is about 1500 Yen.
With such feeling, the ちび ちび cutting
It goes.
If there is a compressor, with the air saw
It can make easy, however it is, don't you think? the ぇ.
09-18-2006 | 10:36 PM
#9
jersey fresh
Joined: Dec 2005
Posts: 3,688
Likes: 0
From: Boston, MA
Furthermore, it finishes to here.
Before painting, already just a little it is to be cut off, does.
Temporarily, time it is required.
Headache may do,
When it paints, such feeling?
Already, just a little, the finish is bad, don't you think? is.
The mark of the paper coming out, it increases.
(Also the photograph is bad, is.)
It is halfway lapse.
Because there are left and right, it is serious.
After, of the net is not thought, as for the て.
09-18-2006 | 10:38 PM
#10
jersey fresh
Joined: Dec 2005
Posts: 3,688
Likes: 0
From: Boston, MA
When you complete, such feeling
Paper in 400．600．1000 turn
Applying correcting, re-paint
Brilliant black for ホルツマツダ car
As for wire net, at foam/home center,
One for screen door of 10 cm 100 Yen
Net of aluminum
The reverse side, turning back,
Stopping at the hot bond
Completion!
When you install, it becomes such feeling.
Because the inside, is completely visible, unless it paints in black
09-19-2006 | 03:25 AM
#15
I don't buy Kool-Aid
Joined: Apr 2004
Posts: 8,823
Likes: 2
From: Vegas Baby!
Originally Posted by msrecant
And all this effort ends up accomplishing what?
09-19-2006 | 05:05 PM
#18
Good one dills! Oh don't sweat it, I didn't translate anything. I just plugged the address into a language translator and that was what popped out.I'm not saying this is a functional mod, I just can't stand how the side vents look. Not a fan of plastic...
10-07-2006 | 07:04 PM
#25
Boricua Hasta La Muerte
Joined: Oct 2003
Posts: 158
Likes: 0
From: Jacksonville, FL
Did Mine today, took all day since you gotta wait for paint to dry, but the results are...., well he are the pics. I took the last picture with the flash on, so you can see that I did not use a grill but painted the inside part of the fender wall, plus I painted them in low gloss black, instead of the glossy black. I put a grill on the first one but took it off because didn't like the look.
Enjoy,
RX8Power
Enjoy,
RX8Power
Last edited by rx8power; 10-07-2006 at 07:08 PM.