Actually it's spelled "Dynamat®"

S

 

You have to pronounce the "®" when you say it too

 

Damn. Might havta go with that stuff. I rather get it sooner then later since I wouldnt wanna install all of it to find out i got a rattle

 

http://www.sounddeadenershowdown.com/

 

damn. i was thinking only doing it to the trunk. wow thats more then i thought. great read, thanks

 

Do you think I should go with this?

ALPINE SWR-1022D 10" Type-R Series Subwoofer $228 for a pair

Frequency Response: 30Hz - 1kHz
Kevlar Reinforced Pulp Cone
High Excursion ľ" Santoprene® Surround
Dual Voice Coil
Custom Cast Aluminum Frame
Integrated Leg Vent System
Bumped Backplate
Heat Transfer Plate
High Strength Brass Voice Coil Bobbin
Double Stacked Magnets
Oversized Parabolic Dustcap
Magnetically Optimized Motor Structure
Designed and Engineered in the USA

ALPINE PDX-1.1000 1 CHANNEL CAR AMPLIFIER AMP PDX1.1000 $400
mono subwoofer amplifier
1,000 watts RMS x 1 at 4 ohms (1,000 watts RMS x 1 at 2 ohms)
variable low-pass filter (50-200 Hz, 24 dB/octave)
Class-D amplifier design
stackable installation design with front-panel controls
quick-connect speaker connectors
preamp-level inputs and outputs
MOSFET power and output stages
fuse rating: 20A x 4

 

i had bought that box but i sold it for like $10 bucks because it was just sitting in my garage. their boxes are ok

 

did you build a cover over the drop bown box in front of the box?

 

Markryan, looks like awesome choices. They will pound without a doubt.

Wicked1044, that cover comes stock. I've heard other members say they do not have this either, but that cover is a Mazda part. Came with mine. Perfectly cut with tabs that fit into the plastic tub.

 

anybody have a pic out of the trunk? just curious how you fit that through the trunk opening....... i have corner stealth boxes and they were a bitchhh to put in...

 

Mine didn't come with the cover either....

 

That lid comes w/ the cargo tray. The box barely fits through the trunk opening. You angle 1 end down through the opening and slide it in.

 

The box cover thing came with it, ordered it from the dealer. They might be able to just order the cover for you.


i had to sorta kick it in there lol... my Apline Subs come tomorrow. Now just gotta order the amp

 

I'll "third" the note of the box being extremely tight through the trunk opening. lol But it fits without removing the weatherstripping or anything.

 

Don't forget to sound dampen your licence plate this is where most of the rattle will come from

P.S

I'm currently using the setup your planing the 2X R Types and the PDX 1.1000 amp and loving it.

 

i had to install my sub after i put the box in the trunk.

 

2nd'ed

 

im looking to sell my box that i have it is the biggest you can get without passing the bottom hole edge in he bottom of the tunk i paid 350 to get it custom molded and installed it will be going for close to that price the reason i stress that it is big is that the other box( which i ad) is too small to get too much bass out of it , this box has 1.3 cu ft.

 

fox, thats clean set up.

 

thanks but im looking to bing the outsides out a lil more to get some more air space so i can port them to get a little louder sound its about 1.1 cu ft with the speakers in it so it doesn't reach the lows i want it to

 

soo if i was to throw my old subs,... 2 12inch subs
* 2x Subwoofer Size 12"
* Impedance 4 ohms
* Peak Power Handling 300 watts
* RMS Power Handling 150 watts
* Woofer Surround Ribbed Polyfoam
* Woofer Composition Polymineral
* Sealed Box Volume 1.25 - 3.5 cubic feet
* Ported Box Volume 1.75 - 2.25 cubic feet
* Sensitivity 89.1 dB
* Frequency Response 27 - 500 Hz
* Xmax (millimeters) 9.76 mm
* Top Mount Depth 5-3/4"
* Cutout Diameter 11-1/8"



what would be the best demension for the zenclosure box shuld i order? an do they port it?

 

They will not make a vent of any kind for you. I asked. I even asked if they would just cut me a 4 1/2" perfect circle on one side and I'd fit in some 4" PVC (I was only getting one 12"), they would not do it. So I cut the hole myself. lol Worked like a charm.

For two 12"s, there is no options. They don't make the entire box larger or smaller to my knowledge. And even if they did, larger is always better. The box would have to be 7-8+ cubes before you'd start seeing any adverse affects from it being too large.

 

i didnt order my box from ebay , it was custom made , notice i comes out a lil farther than the ebay box

 

.75cf is not to small for subs that are made for it.

 

Ah stoplosses got pushed back so I'm be out of the army soon... yes! Which means I have 2 weeks to find a installer to do the following:

1x Massive Audio CAP2 Car Audio 2 Farad Digital Amplifier Capacitor
2x 10" Alpine Type-R Subs
1x Apline 1.000PDX AMP

I'm thinking putting the CAP on the sub box inbetween the 2 subs, or on the back of the box so u can see it when open up the rear glove box like thing (would mean they'd have to cut out some of the glove box thing).

The amp will go into the left side of the cargo tray... eventually i'll add another to the right side and run 1 amp to 1 sub.