Corksport installed with pics
#27
If you're as fed up as I am with the lack of choices we have then contact them and let them know you want one available, they'll definitely release it sooner if they know a ton of people want one.
http://www.metraonline.com/contact.aspx
Last edited by canaryrx8; 03-04-2008 at 03:16 PM.
#28
I can't really divulge too much other than too say an alternative is coming, I just don't know when.
If you're as fed up as I am with the lack of choices we have then contact them and let them know you want one available, they'll definitely release it sooner if they know a ton of people want one.
http://www.metraonline.com/contact.aspx
If you're as fed up as I am with the lack of choices we have then contact them and let them know you want one available, they'll definitely release it sooner if they know a ton of people want one.
http://www.metraonline.com/contact.aspx
#29
Yessir, the cool thing about Metra releasing one will be availability, when it comes out ANY Metra dealer will be able to order it for you, so that includes Best Buy, Circuit City, Fry's, CrutchField, and countless others. We will no longer be bound to a single place to get a kit or a single manufacturer etc. I was told it will be cheaper as well, and we will not lose any functionality at all. They did an awesome job on the Mazda6 kit, can't wait to see what happens with this one.
#31
Boost Junkie
Join Date: Nov 2003
Location: Orange County, CA
Posts: 683
Likes: 0
Received 0 Likes
on
0 Posts
Whats the story with the ebay pioneer wired remote. Can you post a link or something? I am doing my install next weekend and would like to get something similar.
#32
User and Abuser
iTrader: (3)
http://cgi.ebay.com/PAC-SWI-PS-Steer...QQcmdZViewItem
Connects to the wired remote port on the back of your new Pioneer.
For anyone else reading this, I mounted my GPS antenna INSIDE on passenger side corner of the dash. Works great. No worries of theft or water damage.
And I'm going to be pissed if Metra comes out with a kit that looks as good, performs as good, and is cheaper than the Corksport kit this year. If it's into next year, I'll survive.... but still be upset. lol
Last edited by firebirdude; 03-05-2008 at 12:55 PM.
#33
I should see those guys again in May, and hopefully talk to them before then, I'll be sure to post anything I find out.
#37
User and Abuser
iTrader: (3)
You know... I was wondering about that during installation. But yes, the instructions are RX8 specific and are pretty decent. Here's a link to my thread. Some notes in there I found helpful:
https://www.rx8club.com/series-i-interior-audio-electronics-24/installing-corksport-kit-tomorrow-couple-quick-questions-139493/
https://www.rx8club.com/series-i-interior-audio-electronics-24/installing-corksport-kit-tomorrow-couple-quick-questions-139493/
#40
User and Abuser
iTrader: (3)
the pac pdf is about as hard to understand as it gets:
http://peripheralelectronics.com/per...ns/PESWIPS.pdf
http://peripheralelectronics.com/per...ns/PESWIPS.pdf
You don't have to mess with any resistors. And we use the white wire in mode 3. You can get step by step instructions from www.pac-audio.com/swixprogramming . (scroll to bottom to select the mazda)
In short: (there is a single button and a single LED on the PAC module. I will call them as such)
1) Press and hold the button. Turn on ign. Release button. Tap button 3 times. Wait. The LED will flash the number of times you pressed the button. This means it's in mode 3.
2)Turn the key off
3) turn the key to ign. (dont need to hold the button)
4) LED will flash the 3 sequence again. Press and hold button until LED stays steady. This erases memory.
5)You're ready to program. Press and hold volume up until LED turns off. Release volume up. (LED will turn back on) Press and hold volume down until LED turn off. Release volume down. (LED will turn back on) Repeat IN SEQUENCE for the mute, track up, track down, and finally mode button.
6) wait. After a short period, the LED will begin to flash again. You're done. Turn off ign.
7) Power on ign and test. The steering wheel buttons are not quite as responsive with the PAC module as they were stock. Give each of them a press and quick hold. They'll work.
Last edited by firebirdude; 03-05-2008 at 10:14 PM.
#42
Boost Junkie
Join Date: Nov 2003
Location: Orange County, CA
Posts: 683
Likes: 0
Received 0 Likes
on
0 Posts
So... you planted the GPS antennae where I was going to plant it also. Did you put the metal backing plate under the location, or did you just not use it? The instructions say the nav might be a little off without that plate or being mounted to metal.
#43
User and Abuser
iTrader: (3)
Didn't use it at all. No problems so far. I still haven't "stuck" it to the dash because I wasn't sure if I would keep it there. Now I know the signal is strong enough, I might keep a watch on signal strength for a few days. Then put the plate under it and keep a watch for a few days.
#44
After my prep work with this kit last night, I must say I'm not real impressed. The bracket holes don't line up/screws supplied aren't long enough to install as instructed, the harness has a couple wires on it that were never meant to go on an RX8 which makes me think this harness fits a few different cars, the kit is really just a tiny A/C controller box and a painted piece of plastic. I'm sorry, but I just shelled out over $400 for a dash kit. I expect perfection. I don't see why an A/C controller box and a dime-a-dozen harness needs to cost my first born.
#46
Ninja Name: Shimojikushi
iTrader: (2)
Join Date: Jun 2007
Location: Hacienda Heights, CA
Posts: 263
Likes: 0
Received 0 Likes
on
0 Posts
Hoping to hear some good news about the situation because my radio is acting up and the led display is freaking out.
I work in the circuit city car audio department and would be more than happy to see if i can get some discounted kits for some of you guys. We have some Mazda 6 kits and I like the work they did on that one.
Im crossing my fingers because my radio will be replaced within a couple months and I would hate to have to dish over that much money for the kit alone.
KEEP US POSTED!!
I work in the circuit city car audio department and would be more than happy to see if i can get some discounted kits for some of you guys. We have some Mazda 6 kits and I like the work they did on that one.
Im crossing my fingers because my radio will be replaced within a couple months and I would hate to have to dish over that much money for the kit alone.
KEEP US POSTED!!
Thread
Thread Starter
Forum
Replies
Last Post
JimmyBlack
Series I Major Horsepower Upgrades
273
02-10-2020 10:23 PM
Brooklynite
NE For Sale/Wanted
4
11-10-2015 06:42 PM
projectr13b
Series I Do It Yourself Forum
1
09-06-2015 01:04 PM