Samsung Galaxy Tablet 2 7.0 Installed in NaviHood - Completed!
#153
I was just curious: could you use this to power the tablet instead of using the actual cigarette lighter plug?
Amazon.com : DROK 3A/15W Power Converter DC 8-22V 12V to 5V USB Connector Adapter Car Charger For iPhone/HTC/Nokia : Electronics
Amazon.com : DROK 3A/15W Power Converter DC 8-22V 12V to 5V USB Connector Adapter Car Charger For iPhone/HTC/Nokia : Electronics
#155
Registered
He meant wrapping the whole cigarette lighter in tape after you tap into the power. How else would you wrap it so it doesn't touch other electric things to and output the power to them?
#157
You must have a socket to put yours in then? Otherwise you'd have to wire directly to the connectors on the side of the plug and then, yes, tape it up with electrical tape.
That is if you don't do what most people do and tear the thing apart, solder straight to the board and then tape that up.
While we're on the topic: Anyone know a spot in the cabin to tap into constant 12v other than the fusebox?
That is if you don't do what most people do and tear the thing apart, solder straight to the board and then tape that up.
While we're on the topic: Anyone know a spot in the cabin to tap into constant 12v other than the fusebox?
#159
I just recently bought a Nexus 7 and hope to install it in my car as soon as I find a navihood with the Open/Tilt buttons on eBay or somewhere else.
One quick question... I have an rx8 that did not come with the navihood/gps assembly... if I buy one on eBay can I just switch out my current hood with the navihood without doing any plastic cutting on the top of the dash? (I realize I may have to do some cutting on the assembly to make the tablet fit.)
Also, are there any sites that sell the OEM nav hood?
One quick question... I have an rx8 that did not come with the navihood/gps assembly... if I buy one on eBay can I just switch out my current hood with the navihood without doing any plastic cutting on the top of the dash? (I realize I may have to do some cutting on the assembly to make the tablet fit.)
Also, are there any sites that sell the OEM nav hood?
#160
Add gas, add oil, repeat
iTrader: (1)
I just recently bought a Nexus 7 and hope to install it in my car as soon as I find a navihood with the Open/Tilt buttons on eBay or somewhere else.
One quick question... I have an rx8 that did not come with the navihood/gps assembly... if I buy one on eBay can I just switch out my current hood with the navihood without doing any plastic cutting on the top of the dash? (I realize I may have to do some cutting on the assembly to make the tablet fit.)
Also, are there any sites that sell the OEM nav hood?
One quick question... I have an rx8 that did not come with the navihood/gps assembly... if I buy one on eBay can I just switch out my current hood with the navihood without doing any plastic cutting on the top of the dash? (I realize I may have to do some cutting on the assembly to make the tablet fit.)
Also, are there any sites that sell the OEM nav hood?
Your best bet is to check here: RX-8 Parts For Sale/Wanted - RX8Club.com
or another options might include:
05 RX-8 custom fab install (motorized flip-up screen)
or
JDM Japanese Auto Parts specialists | japanparts.com
part# 091-030-004 or 091-021-002 or 091-028-001
#161
Yes, it's a direct replacement no cutting needed.
Your best bet is to check here: RX-8 Parts For Sale/Wanted - RX8Club.com
or another options might include:
05 RX-8 custom fab install (motorized flip-up screen)
or
JDM Japanese Auto Parts specialists | japanparts.com
part# 091-030-004 or 091-021-002 or 091-028-001
Your best bet is to check here: RX-8 Parts For Sale/Wanted - RX8Club.com
or another options might include:
05 RX-8 custom fab install (motorized flip-up screen)
or
JDM Japanese Auto Parts specialists | japanparts.com
part# 091-030-004 or 091-021-002 or 091-028-001
Alright thanks for the info, how much does the whole navihood usually go for? Is around 200 a good price for it?
#163
Since I'm looking for a nav hood to purchase, what components should come with it?
Is there anything else I'm missing? For those of you that have done it, do you purchase additional wires for the power, acc, etc.?
//EDIT
I just found this thread: https://www.rx8club.com/series-i-int...om-pcb-172054/
Unfortunately it looks like the pics are gone, but that should be ok. If I'm reading it right.. I need to buy 3x 14awg wires?
- The motor
- Open/Tilt buttons with wires
- PCB on the inside and outside
Is there anything else I'm missing? For those of you that have done it, do you purchase additional wires for the power, acc, etc.?
//EDIT
I just found this thread: https://www.rx8club.com/series-i-int...om-pcb-172054/
Unfortunately it looks like the pics are gone, but that should be ok. If I'm reading it right.. I need to buy 3x 14awg wires?
Last edited by _MJ_; 09-24-2013 at 07:25 PM.
#164
Add gas, add oil, repeat
iTrader: (1)
You will need to power the hood as well as run power to the tablet unless, you do what Shell did and use a different hood. https://www.rx8club.com/series-i-int...i-come-225539/
Here is more info:
https://www.rx8club.com/series-i-int...buttons-87146/
https://www.rx8club.com/series-i-int...-issue-224409/
https://www.rx8club.com/series-i-int...tablet-237158/
https://www.rx8club.com/series-i-int...cation-140504/
Or you can go nuts: https://www.rx8club.com/series-i-do-...-system-59957/
Here is more info:
https://www.rx8club.com/series-i-int...buttons-87146/
https://www.rx8club.com/series-i-int...-issue-224409/
https://www.rx8club.com/series-i-int...tablet-237158/
https://www.rx8club.com/series-i-int...cation-140504/
Or you can go nuts: https://www.rx8club.com/series-i-do-...-system-59957/
#165
I just recently bought a Nexus 7 and hope to install it in my car as soon as I find a navihood with the Open/Tilt buttons on eBay or somewhere else.
One quick question... I have an rx8 that did not come with the navihood/gps assembly... if I buy one on eBay can I just switch out my current hood with the navihood without doing any plastic cutting on the top of the dash? (I realize I may have to do some cutting on the assembly to make the tablet fit.)
Also, are there any sites that sell the OEM nav hood?
One quick question... I have an rx8 that did not come with the navihood/gps assembly... if I buy one on eBay can I just switch out my current hood with the navihood without doing any plastic cutting on the top of the dash? (I realize I may have to do some cutting on the assembly to make the tablet fit.)
Also, are there any sites that sell the OEM nav hood?
#167
2013 Nexus 7? Let me tell you, it will be an incredibly, incredibly tight fit. There is almost no room left at all on the sides. You will likely have to wire your own connectors or potentially need to hard wire directly to the tablet circuit board. You may have an easier time of it if you only hook up USB and don't use the audio plug, but even then you'll need to whittle the connector down to nothing.
Let me see if I got the wiring right for this whole project though:
I based it all off this image:
1Q (Battery) - Goes directly to the battery (or is there a wire tap somewhere?)
1O (Acc) - Attached to the power on the back of the cigarette lighter
1V (Light) - Attached to the lights of the cigarette lighter
1X and 1P (Ground) - Grounded somewhere
Tablet - Micro usb in tablet connected to a secondary cig lighter socket or connected to a 12V ACC.
Last edited by _MJ_; 09-25-2013 at 10:46 AM.
#168
Add gas, add oil, repeat
iTrader: (1)
2013 Nexus 7? Let me tell you, it will be an incredibly, incredibly tight fit. There is almost no room left at all on the sides. You will likely have to wire your own connectors or potentially need to hard wire directly to the tablet circuit board. You may have an easier time of it if you only hook up USB and don't use the audio plug, but even then you'll need to whittle the connector down to nothing.
Have you tried to fit a new Nexus 7 in the hood? The current 7 is almost exactly the same size as the previous: it's only 1.5cm taller
#169
I refuse to punch a hole in the side of the nav housing to make it all fit and have gone to great lengths to make sure that won't be necessary.
I should have it installed within a week. I'll post some pics and whatnot of the teardown and what was involved to install it when it's all done (in a new thread).
Last edited by o0o0o; 10-03-2013 at 09:19 PM. Reason: Er, had to RMA it ... so longer than a week :(
#172
The placement of the audio plug in particular (top right) would make a hole extremely obvious, unless I positioned it so the power button was facing downward. I'd rather keep the power button up top, so I can theoretically take off one of the bumper sticker things on the front top left of the nav housing and press the power button without taking apart the whole set-up.
#175
I have my Nexus 7 coming in on Tuesday, still looking for an OEM navigation housing but i've emailed about 15 different places that are currently carrying them. Hopefully I can get some advice/opinions from you guys if you happen to install it before me!