shadycrew31

iTrader: (6)

What else is there to discuss his build is done?

TeamRX8

iTrader: (25)

let's see some high boost datalogs or something

9krpmrx8

iTrader: (46)

I will be doing some tuning and fine tuning some components here soon enough. I just needed a break from wrenching for a week or so and just wanted to enjoy my car for a bit

shadycrew31

iTrader: (6)

Me too man... I was 30 seconds away from starting a part out thread the other day.

TeamRX8

iTrader: (25)

that's Ok, I didn't think you were fully done yet

though I can appreciate that it might qualify as fully completed for some shady character

shadycrew31

iTrader: (6)

Nothing is ever complete in the car modification world

I just knew he was done to the point of making mad torques yo.

9krpmrx8

iTrader: (46)

I did do one mod today, I replaced my glove box

RotaryMachineRx

iTrader: (1)

I dunno man, he has lightweight rims, lower and exhaust only and I was kinda with him in 1st and 2nd but by third he was pulling on me hard; and 4th not even competition....

shadycrew31

iTrader: (6)

Time for a BNR upgrade.

Blacknightz

did u video that **** ???

9krpmrx8

iTrader: (46)

Yeah with a stock Greddy you don't stand a chance.

RotaryMachineRx

iTrader: (1)

Haha, I'm scoping out Gregs build and will potentially be swapping my whole kit if it can throw down....

and

No but it is my roommate so I could easily do that with video again... I'm also sure I would do much better if I have my EBC installed and tuned, right now it's running all off the wastegate spring.......


My garage is a total disaster of car parts from S2K, SRT4, Camaro and the 8 right now.... it will be getting a good clean this weekend then I can hopefully get some wrench time in to get the EBC installed. I recently started a new career so I have been quite busy during the week days but now that I have a good routine going I should be able to get my act together!!

9krpmrx8

iTrader: (46)

Here is a little run I did this AM from 50mph to 8-9psi or so before I backed off. Felt really strong.

http://www.flickr.com/photos/9krpmrx8/8026938803/

RIWWP

iTrader: (2)

Something is off with that sheet 9k. Compare RPM to speed....

9krpmrx8

iTrader: (46)

What could be off about it? It's pulled straight from the Cobb datalog.

RIWWP

iTrader: (2)

Hmm, maybe it's the low sampling rate. I guess that you had 2 gear changes in there then...

RIWWP

iTrader: (2)

Yeah, nevermind. There were shifts that weren't really picked up. Sorry, head is fuzzy today

Wasn't expecting a sampling rate of half a second, which was messing with me further.

J8635621

iTrader: (10)

9 sec 40-90? Slow

dannobre

iTrader: (3)

What do you think the AFR's really are?..the WB is pegged rich in most areas....

9krpmrx8

iTrader: (46)

The richest I saw on my PLX was 10.8.

Chris

iTrader: (10)

which is most likely the lowest plx reads so could be lower then that.

lol my logs look the same when I hit 150 cal load

9krpmrx8

iTrader: (46)

Just a fun run, not a full power pull.

shadycrew31

iTrader: (6)

I can get you a 20g wheel and machined greddy housing if you want. I can keep it oil cooled or you can go water/oil cooled.

All you would need to do is remove the Vband and slide the CHRA in.

9krpmrx8

iTrader: (46)

My PLX goes to 10.0 and when I get near 10.0 at WOT I misfire. Although i don't do that anymore since fixing the issue.

RotaryMachineRx

iTrader: (1)

Thanks Shady, I'll keep that in mind, but to be honest I'm interested in the larger BB turbo because ultimatly I'd like to hit that 350whp range.... also I don't have much spare cash at the moment becasue I just bought a DD and I'd like to grab a BHR ignition set-up sooner than later along with some new plugs. Hopefully my stock coils are still in good enough shape that it won't lean my tune out..... 60000 km (37 282 mi) on what I'm assuming are the original coils (plugs have been replaced before). Bought the car in 08 with 13000 km (8078 mi).