Brettus turbo 111 (the ultimate Renesis turbo ?)
#1876
No respecter of malarkey
iTrader: (25)
I was trying w/m into the APV runners only . Thought It might do some majic as there is no fuel injected into them and maybe that was an issue at high power ...... . It didn't do anything special so I gave up on it.
If you are referring to my 'ceiling' theory ....then yes of course it's still a theory . That test was never trying to prove or disprove it so not sure why you would say that .....
If you are referring to my 'ceiling' theory ....then yes of course it's still a theory . That test was never trying to prove or disprove it so not sure why you would say that .....
I think you read too much negativity into my intent. No, the old Team is not back.
I would have liked to have seen you try is all. Of course that’s easy to say when it’s someone else’s engine.
.
#1877
I have to say I'm pretty sick of pulling and refitting engines .
My current thinking is that , to make more power than what it made previously , there are still a few tricks I can employ but ultimately, I need to improve the hp output per gram of air .
Increasing the grams/s (aka , upping the boost) with better cooling/octane may seem like the logical thing to do but IMO, once you pass the mass flow ceiling of the engine , anything you do is just fighting a forest fire with a garden hose.
My current thinking is that , to make more power than what it made previously , there are still a few tricks I can employ but ultimately, I need to improve the hp output per gram of air .
Increasing the grams/s (aka , upping the boost) with better cooling/octane may seem like the logical thing to do but IMO, once you pass the mass flow ceiling of the engine , anything you do is just fighting a forest fire with a garden hose.
#1878
Registered
iTrader: (2)
Is it possible you were injecting too close to the intake ports such that the w/m did not have time to vaporize? I'm assuming you tapped into the intake manifold in order to run it to only the APV runners. Perhaps injecting prior to the throttle body might be more effective.
Though as Team said, it's easy for me to comment as it's not my motor being put at risk.
#1879
Is it possible you were injecting too close to the intake ports such that the w/m did not have time to vaporize? I'm assuming you tapped into the intake manifold in order to run it to only the APV runners. Perhaps injecting prior to the throttle body might be more effective.
Though as Team said, it's easy for me to comment as it's not my motor being put at risk.
Though as Team said, it's easy for me to comment as it's not my motor being put at risk.
#1882
No respecter of malarkey
iTrader: (25)
Only because people like yourself have so overly misused it. They list a bunch of SJW crap on there now too. Dictionaries are only cultural extensions of what’s trending and no longer the definitive source on what’s actually correct or not. The entire education system is fubar now for the same reason.
Motor - electrical
Engine - combustion
Motor - electrical
Engine - combustion
The following users liked this post:
Charles R. Hill (06-02-2019)
The following users liked this post:
Brettus (06-02-2019)
#1888
In other unrelated news :
Having another shot at this IC design as I wasn't happy with the temp rise I'm seeing. This core has higher fin density and will have a baffle in the bottom tank. I cut the end tanks off the old IC and am getting them welded to a new core.
Old core internal : 9 fins/inch 10mm long offset fins
New core internal : 11 fins/inch 5mm long offset fins
Also cut the tanks so the taper is more ...like the Treadstone design.
Having another shot at this IC design as I wasn't happy with the temp rise I'm seeing. This core has higher fin density and will have a baffle in the bottom tank. I cut the end tanks off the old IC and am getting them welded to a new core.
Old core internal : 9 fins/inch 10mm long offset fins
New core internal : 11 fins/inch 5mm long offset fins
Also cut the tanks so the taper is more ...like the Treadstone design.
Last edited by Brettus; 06-04-2019 at 04:36 PM.
#1890
That's the outlet not the intlet . There really isn't any other option for it . But I am fitting a baffle on the inlet tank in case the end passages are getting too much flow due to easy run into the outlet elbow.
Last edited by Brettus; 06-05-2019 at 04:07 PM.
The following users liked this post:
sinkas (06-09-2019)
#1895
Hi Brettus,
I think that intercooler end tank design is not ideal according to Garrett.
Here's what Garrett recommends.
Another important factor in selecting the correct intercooler is the end tank design. Proper manifold shape is critical in both minimizing charge air pressure drop and providing uniform flow distribution. Good manifold shapes minimize losses and provide fairly even flow distribution. The over-the-top design can starve the top tubes however. The side entry is ideal for both pressure drop and flow distribution, but it is usually not possible due to vehicle space limitations.
Garrett intercooler
I think that intercooler end tank design is not ideal according to Garrett.
Here's what Garrett recommends.
Another important factor in selecting the correct intercooler is the end tank design. Proper manifold shape is critical in both minimizing charge air pressure drop and providing uniform flow distribution. Good manifold shapes minimize losses and provide fairly even flow distribution. The over-the-top design can starve the top tubes however. The side entry is ideal for both pressure drop and flow distribution, but it is usually not possible due to vehicle space limitations.
Garrett intercooler
#1896
I believe the less than ideal efficiency I saw with the mk1 was more to do with the core design, more specifically the internal fin density. My Mk1 version,according to the Treadstone pdf I posted earlier, had a medium density core. That isn't the best design for a vertical IC when the internal channels are very short. This new core is a high density core which will be more restrictive but should provide the balance between pD and efficiency that I'm looking for.
#1898
The funny part about that is .................... I fixed that a couple of years ago and now it actually spools up faster than any turbo this size ever seen on a Renesis . And that even includes the top mount EFRs that you were so adamant would be superior in every way!
#1899
No respecter of malarkey
iTrader: (25)
Now Brettus, what EFR Renesis engine has there ever been where someone wasn’t going full out ‘tard on? The only one I can even recall was that stupid drifter S2 car with a huge 9180. You know if someone got serious with either a 7670 or 8374 that isn’t going to hold up. That’s not to knock either you or your efforts. Let’s face it, you and Slash are about the only two to stick with the Renesis turbo long term. That’s a fairly small puddle to be calling yourself the biggest fish in.
if you have zero dP through the IC then that’s a lot of volume to expand in and then rebuild boost back up, which is going to impact response, but the comment was made in jest, not criticism.
if you have zero dP through the IC then that’s a lot of volume to expand in and then rebuild boost back up, which is going to impact response, but the comment was made in jest, not criticism.
Last edited by TeamRX8; 06-10-2019 at 07:30 PM.
#1900
Now Brettus, what EFR Renesis engine has there ever been where someone wasn’t going full out ‘tard on? The only one I can even recall was that stupid drifter S2 car with a huge 9180. You know if someone got serious with either a 7670 or 8374 that isn’t going to hold up. That’s not to knock either you or your efforts. Let’s face it, you and Slash are about the only two to stick with the Renesis turbo long term. That’s a fairly small puddle to be calling yourself the biggest fish in.
if you have zero dP through the IC then that’s a lot of volume to expand in and then rebuild boost back up, which is going to impact response, but the comment was made in jest, not criticism.
if you have zero dP through the IC then that’s a lot of volume to expand in and then rebuild boost back up, which is going to impact response, but the comment was made in jest, not criticism.
I take your point re the IC and with any luck the mk2 IC will improve things. And I did see it as a joke ...meant to stir me up ... It worked lol!