there's always the option to raise the engine and provide some more room down low
|
Hi all, newbie here, subscribed to this thread. Very interested to see progress and results.
I'm impressed with the WG idea. OP: did you buy the GT3582r with the twinscroll housing or did you have to buy the housing separately? seems like it has to be purchased separately here in UK :( |
Originally Posted by shambo
(Post 4704989)
Hi all, newbie here, subscribed to this thread. Very interested to see progress and results.
I'm impressed with the WG idea. OP: did you buy the GT3582r with the twinscroll housing or did you have to buy the housing separately? seems like it has to be purchased separately here in UK :( These guys might be a good bet too . Note you can spec it however you want . : http://www.atpturbo.com/mm5/merchant...egory_Code=GRT |
Originally Posted by Brettus
(Post 4704992)
I was able to spec what i wanted and the supplier put it together for me .
These guys might be a good bet too . Note you can spec it however you want . : Garrett GT3582R (aka GT35R, aka GT35/40R) Bearing Turbo : atpturbo.com http://tuitionmanagementsystems.com/...es-298x300.jpg |
Originally Posted by shambo
(Post 4704993)
oh nice, thanks for the link, only problem for me now is:
http://tuitionmanagementsystems.com/...es-298x300.jpg |
question, are you running standard 10:1 compression in this motor or have you reduced it?
|
Has anyone released low compression rotors for Renesis?
|
One o the Pettit SC guys has low compression rotors ... they need to be machined for the oil control rings . I'm running stock.
|
Originally Posted by firecran
(Post 4704933)
Bends everywhere!
At least the turbo mani and renny exhaust ports will match ;) https://cimg9.ibsrv.net/gimg/www.rx8...ba1786e2b3.jpg |
I just want to know if you will leave the APV closed or not :hahano:
. |
Originally Posted by TeamRX8
(Post 4705301)
I just want to know if you will leave the APV closed of not :hahano:
|
Update :
Manifold is complete Engine mount complete Wastegate mounting complete Turbo inlet complete Turbo outlet complete Yet to do : Wastegate return to DP Downpipe Midpipe (remove neck down restrictions and mod for v band) Water lines Oil lines Heat shielding. ETA : end of next week. |
I await with the utmost anxiety.
|
I'll give you the same rule I give my buddies.... "Pics or it didn't happen" :lol:
|
Originally Posted by Brettus
(Post 4705311)
:scratchhe
|
Brettus... Forgive me if I have missed this but what ecu and fuel system are you going to use? Only asking as I'm planning on putting Renesis engine trans and rear axle into my car and looking to do something similar to what you're doing here. Thx.
|
^ Stock ECU tuned with Cobb AP is the way to go (but sounds like you are not doing this to an 8); and I'm certain that is what Brett is using but I'll let him have the final say on that..... I'd say 99% of people around here are going to recommend that route on an FI'd 8. What vehicle are you planning to drop this into?
|
Originally Posted by rotarymachinerx
(Post 4705352)
what vehicle are you planning to drop this into?
|
Brettspeed is all about mazdaedit
|
10-4
|
Originally Posted by FazdaRX_8
(Post 4705407)
Brettspeed is all about mazdaedit
*edit* just reading through Brettus original thread about it now :) |
Originally Posted by shambo
(Post 4705463)
is this regarded as the best choice for FI applications?
*edit* just reading through Brettus original thread about it now :) I think the Adaptronics would do it .......... Team ? As far as doing the same thing goes .... might work out better in an application that has the room . I would certainly not use the turbo I did if I had more room . |
IMO if you're talking about swapping an FI rotary into a different chassis then the REW or Cosmo 13B is the way to go rather than a Renesis
Come to think about it, RX8 chassis too ... :lol: . |
Originally Posted by TeamRX8
(Post 4705478)
IMO if you're talking about swapping an FI rotary into a different chassis then the REW or Cosmo 13B is the way to go rather than a Renesis
Come to think about it, RX8 chassis too ... :lol: . |
Originally Posted by TeamRX8
(Post 4705478)
IMO if you're talking about swapping an FI rotary into a different chassis then the REW or Cosmo 13B is the way to go rather than a Renesis
Come to think about it, RX8 chassis too ... :lol: . |
All times are GMT -5. The time now is 06:21 AM. |
© 2024 MH Sub I, LLC dba Internet Brands