CEL code P2070?
#26
8 all the way
Thread Starter
Join Date: Nov 2005
Location: Killeen, Tx
Posts: 340
Likes: 0
Received 0 Likes
on
0 Posts
The cel is on constantly now but the car runs fine. I am wondering like tdiddy said if I tune and turn up the boost can I remove the blocking plate? Another thing if I am gonna tune the greddy kit do I need to buy the interceptor x or can the emanage ultimate be tuned to 9 psi?
#27
In addition to what I said in the previous post, the blocking plate also makes tuning easier. Since there is no port opening that causes an influx of air that needs to be delt with.
You can remove it, but you're going to have to do tuning or the car will run lean from that point on. Under boost that will be a serious problem if you run the stock map without changes.
There's no reason why you can't use the Ultimate at higher boost levels. It's just a matter of making sure your map is correctly tuned for that pressure.
You can remove it, but you're going to have to do tuning or the car will run lean from that point on. Under boost that will be a serious problem if you run the stock map without changes.
There's no reason why you can't use the Ultimate at higher boost levels. It's just a matter of making sure your map is correctly tuned for that pressure.
#28
I wanna rock! Rock!
Join Date: Jun 2005
Location: Monterey, CA
Posts: 576
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by tdiddy
Finally, how hard do you think it would be to tune the car if someone chooses not to install the blocking plate and to modify the wiring harness so that the APV opened?
I'm going to go ahead and install the plate and use greddy's supplied map for awhile, and add any input I may have.
#29
I have the plate in my car, but I didn't do the install myself. Is it just a few 12/10mm bolts and some rubber hoses that need to come off? Looks like there's one bolt in the back that might be a pain to get to.
#30
X-Sapper
Join Date: Jan 2004
Location: where angle's fear to tread
Posts: 2,392
Likes: 0
Received 0 Likes
on
0 Posts
i just had a code coem on "intake runner stuck open (bank 1)"
i don't have a turbo (just bad luck aparently). it came on after i drove abotu 20 miles. turned teh car on 4 hours later it went off......while driving to the dealership it came back on (about 21 miles). they are taking a look at it...but since i still have 609 miles on my extended powertrain warrenty i am antisipating me getting a new intake manifold. they are rather pricy....
i don't have a turbo (just bad luck aparently). it came on after i drove abotu 20 miles. turned teh car on 4 hours later it went off......while driving to the dealership it came back on (about 21 miles). they are taking a look at it...but since i still have 609 miles on my extended powertrain warrenty i am antisipating me getting a new intake manifold. they are rather pricy....
#34
well just out of curiousity if ur worrying about a carbon buildup issue, couldnt u just hook up a intake system cleaner through the brake booster vacuum line that runs to the intake manifold.........hook it up there n clean out the intake side for any carbon deposits that might have built up.......just as a thought.........
#35
btw, I took off the turbo blocking plate and haven't gotten the CEL since.
I'm pretty sure the blocking plate can cause the CEL to go off - though it is intermittent, and not a constant thing.
I'm pretty sure the blocking plate can cause the CEL to go off - though it is intermittent, and not a constant thing.
#36
I wanna rock! Rock!
Join Date: Jun 2005
Location: Monterey, CA
Posts: 576
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mysql101
btw, I took off the turbo blocking plate and haven't gotten the CEL since.
I'm pretty sure the blocking plate can cause the CEL to go off - though it is intermittent, and not a constant thing.
I'm pretty sure the blocking plate can cause the CEL to go off - though it is intermittent, and not a constant thing.
I figured the resistors in the EMU harness would have caused the light, since they electrically prevent the ports from opening.
#38
Originally Posted by mikeschaefer
Did you have the plate on with the int-x?
I figured the resistors in the EMU harness would have caused the light, since they electrically prevent the ports from opening.
I figured the resistors in the EMU harness would have caused the light, since they electrically prevent the ports from opening.
Originally Posted by Terrance26
Can I take out the blocking plate and tune the emanage ultimate to run without it?
Thread
Thread Starter
Forum
Replies
Last Post
Shankapotamus3
Series I Trouble Shooting
28
03-14-2021 03:53 PM
Evan Gray
Series I Trouble Shooting
0
09-26-2015 12:30 PM