Dondo's Supercharger Build
07-04-2010 | 12:46 PM
#251
Thread Starter
100% baller (finally!)
iTrader: (7)
Joined: Jun 2007
Posts: 5,385
Likes: 2
From: Seattle, WA
now i need to get to data logs and tuning.
here's a pic before we put the front clip back on last night:
![mike[piston eater]'s Avatar](https://www.rx8club.com/avatars/mike%5Bpiston-eater%5D-48728.gif?dateline=1334247180)
07-04-2010 | 04:28 PM
#260
Thread Starter
100% baller (finally!)
iTrader: (7)
Joined: Jun 2007
Posts: 5,385
Likes: 2
From: Seattle, WA
What BHR did on Dondo's car;
1) Installed used Pettit S/C kit.
2) Installed Sohn OMP adapter.
3) Installed GReddy Oil Filter Relocation kit.
4) Installed AEM alcohhol injection system.
5) Installed RC Engineering P2 fuel injectors.
6) Custom fabricated a cold-air intake.
7) Installed AIR pump block-off plate.
8) Cleaned up some underdash wiring.
9) Properly installed poorly installed interior trim pieces.
10) Enjoyed Dondo's top-notch, classy, hosting skillz.
I will elaborate on the nuances of each thing when I can use something other than my shitty HTC HD2 with the truly AWFUL Windows OS.
Easy can remember and post about what I may have forgotten.
1) Installed used Pettit S/C kit.
2) Installed Sohn OMP adapter.
3) Installed GReddy Oil Filter Relocation kit.
4) Installed AEM alcohhol injection system.
5) Installed RC Engineering P2 fuel injectors.
6) Custom fabricated a cold-air intake.
7) Installed AIR pump block-off plate.
8) Cleaned up some underdash wiring.
9) Properly installed poorly installed interior trim pieces.
10) Enjoyed Dondo's top-notch, classy, hosting skillz.
I will elaborate on the nuances of each thing when I can use something other than my shitty HTC HD2 with the truly AWFUL Windows OS.
Easy can remember and post about what I may have forgotten.
07-05-2010 | 09:53 AM
#262
Registered
Joined: Oct 2007
Posts: 1,574
Likes: 2
From: Boosted...
I like the "coin tray" to control idea; how visible is that to your driving position?
/I got to go sit in my 8 and look...
Also, has anyone done a supercharged with nitrous installation?
07-06-2010 | 06:24 PM
#272
Thread Starter
100% baller (finally!)
iTrader: (7)
Joined: Jun 2007
Posts: 5,385
Likes: 2
From: Seattle, WA
really good actually. no leaks. good power. and it's still on the FI base tune from MM. data logs are submitted though so i'm just waiting on the first tune to come over.
finished the battery box with tie downs and just need to figure out how i want to wire in the oil level sensor. the battery cover still fits too.
also got the mazdaspeed strut tower brace back in place so it's just about buttoned up. only need to find some clear washer fluid now and finish wiring in the GOODbox gauge
finished the battery box with tie downs and just need to figure out how i want to wire in the oil level sensor. the battery cover still fits too.
also got the mazdaspeed strut tower brace back in place so it's just about buttoned up. only need to find some clear washer fluid now and finish wiring in the GOODbox gauge
07-07-2010 | 03:50 AM
#275
Jingle Ballzzzz!
Joined: Mar 2006
Posts: 2,358
Likes: 15
From: Renton, WA, USA, No. Am, Planet Earth
+1 
Oh man....!
Congrats Mike!! Remember you owe me....
Here are my pics from Friday night when I came out to see the install and have my compression tested (thanks again Shaun for doing it, and Kev for leaving your tester).
Hard at work!
Friday night, as of 10pm
Can you tell they're hungover from Thursday night Dick's shenanigans?
After dinner at The Keg at midnight
Oh man....!Congrats Mike!! Remember you owe me....
Here are my pics from Friday night when I came out to see the install and have my compression tested (thanks again Shaun for doing it, and Kev for leaving your tester).
Hard at work!
Friday night, as of 10pm
Can you tell they're hungover from Thursday night Dick's shenanigans?
After dinner at The Keg at midnight
Last edited by 05TiGr8Lady; 07-07-2010 at 03:57 AM.