Dondo's Supercharger Build
#152
Registered
iTrader: (2)
Lol---tell easy I only take Greyhound short buses!
small pulley or big pulley?
if yall took that fuel injector gas line off --do not reuse it.
good time to insulant the fuel lines/rail--the gas inside the rail can get up to 180F without it.
you are going to run a cat?
deleting that air pump sure gives to a lot of room and you can put heat shield on the exhaust a lot easier.
I placed a dei heat shield over the oem header and then attached the aluminum oem shield on top of that--sure helped a lot.
taking that pump out also clears up a area if which the remote oil filter can go
That remote is a clean looking job.
hint on the dip stick----straighen out the yellow curled end of it and attach and extension--such as the tube that comes with that magnet ch was using. use a good epoxy and ram the dip stick end down in there. once it dries, bend it in a Z manner so it will clear everything--then just expoy a chrome lug nut on top of the new handle and it looks like a real custom job. Makes checking the oil easier as you dont have reach way down there to get to it.
ok i will shut up now.
od
small pulley or big pulley?
if yall took that fuel injector gas line off --do not reuse it.
good time to insulant the fuel lines/rail--the gas inside the rail can get up to 180F without it.
you are going to run a cat?
deleting that air pump sure gives to a lot of room and you can put heat shield on the exhaust a lot easier.
I placed a dei heat shield over the oem header and then attached the aluminum oem shield on top of that--sure helped a lot.
taking that pump out also clears up a area if which the remote oil filter can go
That remote is a clean looking job.
hint on the dip stick----straighen out the yellow curled end of it and attach and extension--such as the tube that comes with that magnet ch was using. use a good epoxy and ram the dip stick end down in there. once it dries, bend it in a Z manner so it will clear everything--then just expoy a chrome lug nut on top of the new handle and it looks like a real custom job. Makes checking the oil easier as you dont have reach way down there to get to it.
ok i will shut up now.
od
#164
Banned
iTrader: (3)
Why? It is designed to be reused. That is why it has a quick-disconnect.
I've probably pulled mine off two dozen times.
So? It's not a drag-car and it's not carbureted.
The OE manifold is already really well insulated by design.
It is double-walled and shielded with a shroud and a blanket.
I don't think they are building a 1920's Roadster.
Here's a mod for you:
I've probably pulled mine off two dozen times.
It is double-walled and shielded with a shroud and a blanket.
Here's a mod for you:
#167
Registered
iTrader: (3)
never thought i would say this --but MM there is a "search" feature on the forum........use it!
yall forget i am trying to turn the rx8 into a mustang and i use parts out of my Fred Sanford backyard.
Theres that damn gremblin thats we have seen around here? it even looks evil. stick one of those bhr spark wires up his butt!
OD
yall forget i am trying to turn the rx8 into a mustang and i use parts out of my Fred Sanford backyard.
Theres that damn gremblin thats we have seen around here? it even looks evil. stick one of those bhr spark wires up his butt!
OD
#172
Power!!
As a side note guess who just put up the worst compression numbers in history for a rebuild from Mazda with 12k miles on it grab ya?
How about 5.0 on the lowest face at 250 rpm adjusted.
Edit: updated rpm.
How about 5.0 on the lowest face at 250 rpm adjusted.
Edit: updated rpm.
Last edited by shaunv74; 07-02-2010 at 10:53 PM.