Emanage map is gone!!
#1
Turbo'd 5
Thread Starter
Join Date: Jun 2004
Location: Dalton, GA
Posts: 531
Likes: 0
Received 0 Likes
on
0 Posts
Emanage map is gone!!
I just installed my profec E-01 the other day and everything was fine. I started messing around with increasing the boost and all of a sudden it said that there was no map on the Emanage!! I'm not sure what happened but I uploaded the map on the emanage to the profec and it's completely blank. What can I do now?? Where can I find a new map or one that someone else has made and is there any way to upload it using just the E-01??
Jamie
Jamie
#3
Turbo'd 5
Thread Starter
Join Date: Jun 2004
Location: Dalton, GA
Posts: 531
Likes: 0
Received 0 Likes
on
0 Posts
Well my car is sitting in the driveway and isnt moving till it has the map back. I have the support tool and I'm going to try and upload some new maps. Anything that I should note before I do this?
#4
Administrator
ahha! yeah talk to Horse https://www.rx8club.com/showthread.p...81#post1039681 he's the one who had the same thing happen
#6
Consiglieri
Join Date: Feb 2004
Location: yourI'mgirl
Posts: 1,275
Likes: 0
Received 0 Likes
on
0 Posts
I took an extra precaution and just installed the Profec for a few weeks - no turbo. That gave me the opportunity to see that the Profec really can't communicate with the emanage. When you load to the Profec, it doesn't get the settings right, even if they are right on the emanage. Not sure why. Benny at GReddy is aware of this, but I don't know if they are doing anything about it.
For now, its support tool ONLY for me!!
For now, its support tool ONLY for me!!
#8
Ex- member.
Map being erased due to E-01 happened to me too!
I was messing around testing it out after a few days of having it installed. I went into the emanage map screens and saw the values and then exited out. I didn't import/export or anything, just viewed. This was in the garage in the evening.
Next morning, started driving and immediately noticed power loss above 3-4k and I couldn't get up to speed. The car was detonating anytime in boost.
Turned around and hooked up the support tool, it's supposed to automatically import the map that's currently loaded on the emanage but I got a blank map! Reloaded map from laptop and I was back to normal.
It scared the heck out of me that I haven't tried to access the emanage maps through the E01.
I was messing around testing it out after a few days of having it installed. I went into the emanage map screens and saw the values and then exited out. I didn't import/export or anything, just viewed. This was in the garage in the evening.
Next morning, started driving and immediately noticed power loss above 3-4k and I couldn't get up to speed. The car was detonating anytime in boost.
Turned around and hooked up the support tool, it's supposed to automatically import the map that's currently loaded on the emanage but I got a blank map! Reloaded map from laptop and I was back to normal.
It scared the heck out of me that I haven't tried to access the emanage maps through the E01.
#9
Registered User
did i see somewhere that the sd card had to be formatted or i am just remembering wrong, i have the profec but don't use it for the emanage maps anymore heard these stories.
#11
Consiglieri
Join Date: Feb 2004
Location: yourI'mgirl
Posts: 1,275
Likes: 0
Received 0 Likes
on
0 Posts
There is an issue with having the right versions of the firmware for both the e01 and the emanage. Mine had the correct versions. It did wierd things like change the y-axis values on the fuel maps from boost, to air flow sensor voltage. No matter what I did, it would ALWAYS revert to air flow voltage. When I checked it with the support too, things were A-okay. But, I don't trust it now. Too bad, huh?
Thread
Thread Starter
Forum
Replies
Last Post
Touge
Canada Forum
1
09-23-2019 06:45 PM
yurcivicsux
Series I Major Horsepower Upgrades
192
09-12-2017 10:54 PM
Touge
Canada Forum
0
09-22-2015 11:51 PM
Touge
Canada Forum
0
09-18-2015 12:21 AM