Greddy Turbo owners thread
#351
/\ have not had a noticeable reduction in boost due to warmer temperature - but have seen a little less flow .
Start getting into the habit of regularly logging g/s and that will give you a base point to reference if there is any issues . Also is the best way to monitor any improvements you make .
Start getting into the habit of regularly logging g/s and that will give you a base point to reference if there is any issues . Also is the best way to monitor any improvements you make .
#352
Posted this in another thread - Thought it would be worth posting here as well .
WHP progression for the Greddy kit :
240- 260whp - stock greddy turbo with the usual recommended upgrades
280-300 whp - Upgrade the compressor to BNR T04e 50 trim or equivalent .Do the wastegate mod or upgrade the actuator . No other major changes required.
330-350 whp - Upgrade the compressor to BNR 60-1 , upgrade the suction piping to 21/2" min the compression piping to the I/C to 21/4" min , upgrade the I/C . Modify the turbo exit for better flow . Fit 3" exhaust . Upgrade fuel pump , injectors , ignition .Do the wastegate mod or upgrade the actuator. Then pray it all hangs together
WHP progression for the Greddy kit :
240- 260whp - stock greddy turbo with the usual recommended upgrades
280-300 whp - Upgrade the compressor to BNR T04e 50 trim or equivalent .Do the wastegate mod or upgrade the actuator . No other major changes required.
330-350 whp - Upgrade the compressor to BNR 60-1 , upgrade the suction piping to 21/2" min the compression piping to the I/C to 21/4" min , upgrade the I/C . Modify the turbo exit for better flow . Fit 3" exhaust . Upgrade fuel pump , injectors , ignition .Do the wastegate mod or upgrade the actuator. Then pray it all hangs together
Last edited by Brettus; 04-27-2011 at 04:09 PM.
#353
Well my rebuild is complete with the NRS ceramics and i just received my turbo back from BNR soon as I get everything back together and tuned I will get it dynoed soon after. Only thing I need now is a little more cash haha
#354
Also ... would be worth checking out this wastegate mod before you fit the turbo.
here....... https://www.rx8club.com/showpost.php...22&postcount=1
Last edited by Brettus; 04-29-2011 at 04:52 PM.
#355
With the 50 trim your inlet id is 55ish mm . Make sure you grind out the flange on the inlet pipe (53mm stock i believe) to the same diameter as the turbo inlet before fitting it .
Also ... would be worth checking out this wastegate mod before you fit the turbo.
here....... https://www.rx8club.com/showpost.php...22&postcount=1
Also ... would be worth checking out this wastegate mod before you fit the turbo.
here....... https://www.rx8club.com/showpost.php...22&postcount=1
#358
SPOOLN8
iTrader: (1)
Join Date: Nov 2008
Location: Edmonton, Alberta, Canada
Posts: 2,240
Received 214 Likes
on
161 Posts
So this thread has been a little slow lately.....
Brett I did your WG arm mod and holy ****! I took off the nut from the WG arm and cranked the arm as short as it could go. I was seeing about 10psi and even managed to induced boost creep when my ssv actuator opened up to about 12 psi.
I re-adjusted the arm length so that I cranked it completely as short as it could go, then lengthened it 2 complete 360deg rotations from there. I am now seeing full peak boost of about 9psi at around 3800-4000 rpm. which then drops to around 6.5 or 7 psi by redline. The car is pulling much much harder compared to seeing 5.5 to 6psi peak dropping to about 4psi by redline. AFRs are sitting between 11.0 and 11.5 according to my AP on both 2nd and 3rd gear WOT pulls to redline. Saw a max of 302g/s in 2nd gear, compared to about 260g/s I used to see.
Next I need to get my EBC installed and tuned....
Brett I did your WG arm mod and holy ****! I took off the nut from the WG arm and cranked the arm as short as it could go. I was seeing about 10psi and even managed to induced boost creep when my ssv actuator opened up to about 12 psi.
I re-adjusted the arm length so that I cranked it completely as short as it could go, then lengthened it 2 complete 360deg rotations from there. I am now seeing full peak boost of about 9psi at around 3800-4000 rpm. which then drops to around 6.5 or 7 psi by redline. The car is pulling much much harder compared to seeing 5.5 to 6psi peak dropping to about 4psi by redline. AFRs are sitting between 11.0 and 11.5 according to my AP on both 2nd and 3rd gear WOT pulls to redline. Saw a max of 302g/s in 2nd gear, compared to about 260g/s I used to see.
Next I need to get my EBC installed and tuned....
Last edited by RotaryMachineRx; 08-21-2011 at 04:07 PM.
#360
So this thread has been a little slow lately.....
Brett I did your WG arm mod and holy ****! I took off the nut from the WG arm and cranked the arm as short as it could go. I was seeing about 10psi and even managed to induced boost creep when my ssv actuator opened up to about 12 psi.
I re-adjusted the arm length so that I cranked it completely as short as it could go, then lengthened it 2 complete 360deg rotations from there. I am now seeing full peak boost of about 9psi at around 3800-4000 rpm. which then drops to around 6.5 or 7 psi by redline. The car is pulling much much harder compared to seeing 5.5 to 6psi peak dropping to about 4psi by redline. AFRs are sitting between 11.0 and 11.5 according to my AP on both 2nd and 3rd gear WOT pulls to redline. Saw a max of 302g/s in 2nd gear, compared to about 260g/s I used to see.
Next I need to get my EBC installed and tuned....
Brett I did your WG arm mod and holy ****! I took off the nut from the WG arm and cranked the arm as short as it could go. I was seeing about 10psi and even managed to induced boost creep when my ssv actuator opened up to about 12 psi.
I re-adjusted the arm length so that I cranked it completely as short as it could go, then lengthened it 2 complete 360deg rotations from there. I am now seeing full peak boost of about 9psi at around 3800-4000 rpm. which then drops to around 6.5 or 7 psi by redline. The car is pulling much much harder compared to seeing 5.5 to 6psi peak dropping to about 4psi by redline. AFRs are sitting between 11.0 and 11.5 according to my AP on both 2nd and 3rd gear WOT pulls to redline. Saw a max of 302g/s in 2nd gear, compared to about 260g/s I used to see.
Next I need to get my EBC installed and tuned....
BTW- I did suggest in my thread that you take it one turn at a time rather than go all the way to start with .
Last edited by Brettus; 08-22-2011 at 12:59 AM.
#365
SPOOLN8
iTrader: (1)
Join Date: Nov 2008
Location: Edmonton, Alberta, Canada
Posts: 2,240
Received 214 Likes
on
161 Posts
I know I did do that, but I had the arm as short as I could possibly go with the nut still on the threads and I was only getting about 7psi peak.... So I didn't post about the first few tries where it barely increased. I actually at one point thought that I may be looking for a boost leak because the results were so pewny. What a shock/relief once I saw the boost gauge creep up to 12psi haha; backed it off 720deg and found exactly where I wanted to be.
#366
SPOOLN8
iTrader: (1)
Join Date: Nov 2008
Location: Edmonton, Alberta, Canada
Posts: 2,240
Received 214 Likes
on
161 Posts
Yeah Brettus' thread has it bang on; no need to even remove a wheel; remove 4 17mm bolts, 1 19mm stud and just loosen the 19mm stud on the left side of the car. The xmember just swings out of the way revealing the WG arm then. I easily accessed it by jacking the front end of the car up and crawling under on my back. Got the e-clip with needle nose's and 10mm wrench for the WG arm nut. The needle nose pliers also helped big time to get the arm on and off of the WG flap since you will need to tug on the actuator arm quite a bit once it is shortend.
Last edited by RotaryMachineRx; 08-22-2011 at 11:06 AM.
#368
SPOOLN8
iTrader: (1)
Join Date: Nov 2008
Location: Edmonton, Alberta, Canada
Posts: 2,240
Received 214 Likes
on
161 Posts
I backed it off to ensure that there was no boost creep induced at all Jeff. My boost profile is nearly identical to what it was at stock arm length except 3 to 3.5 psi greater throughout, peak and where it drops of in the higher rpm range.
10psi with boost creep was only a short drive to test where I was at.... which was obviously too much and immediately returned to my garage to back it off.
Although I will keep an eye on my IAT's for a while now to see if I notice a large difference from before..... no way for me to measure EGT's at the moment.
Last edited by RotaryMachineRx; 08-22-2011 at 11:39 AM.
#369
I backed it off to ensure that there was no boost creep induced at all Jeff. My boost profile is nearly identical to what it was at stock arm length except 3 to 3.5 psi greater throughout, peak and where it drops of in the higher rpm range.
10psi with boost creep was only a short drive to test where I was at.... which was obviously too much and immediately returned to my garage to back it off.
Although I will keep an eye on my IAT's for a while now to see if I notice a large difference from before..... no way for me to measure EGT's at the moment.
10psi with boost creep was only a short drive to test where I was at.... which was obviously too much and immediately returned to my garage to back it off.
Although I will keep an eye on my IAT's for a while now to see if I notice a large difference from before..... no way for me to measure EGT's at the moment.
#371
Banned
iTrader: (3)
I backed it off to ensure that there was no boost creep induced at all Jeff. My boost profile is nearly identical to what it was at stock arm length except 3 to 3.5 psi greater throughout, peak and where it drops of in the higher rpm range.
10psi with boost creep was only a short drive to test where I was at.... which was obviously too much and immediately returned to my garage to back it off.
Although I will keep an eye on my IAT's for a while now to see if I notice a large difference from before..... no way for me to measure EGT's at the moment.
10psi with boost creep was only a short drive to test where I was at.... which was obviously too much and immediately returned to my garage to back it off.
Although I will keep an eye on my IAT's for a while now to see if I notice a large difference from before..... no way for me to measure EGT's at the moment.
#372
SPOOLN8
iTrader: (1)
Join Date: Nov 2008
Location: Edmonton, Alberta, Canada
Posts: 2,240
Received 214 Likes
on
161 Posts
Do you guys remember the thread where Jeff and Brett had a "discussion" about this? I remember reading it a while ago (last summer maybe
) but I've been searching and can't find what thread title it was. I'd would like to read that over again since it seems to be the direction this thread is going to go if I keep asking questions.
![Dunno](https://www.rx8club.com/images/smilies/dunno.gif)
![Lol](https://www.rx8club.com/images/smilies/lol.gif)
#373
Banned
iTrader: (3)
Do you guys remember the thread where Jeff and Brett had a "discussion" about this? I remember reading it a while ago (last summer maybe
) but I've been searching and can't find what thread title it was. I'd would like to read that over again since it seems to be the direction this thread is going to go if I keep asking questions. ![Lol](https://www.rx8club.com/images/smilies/lol.gif)
![Dunno](https://www.rx8club.com/images/smilies/dunno.gif)
![Lol](https://www.rx8club.com/images/smilies/lol.gif)
#375
SARX Legend
iTrader: (46)
I actually just got off the phone with AMR (customizing and rebuilding my turbo) and Rob says it is not ideal and will prematurely wear the turbo out if it is standard Greddy unit. He basically said if you push it beyond it's design parameters you will wear out the internals. I also found out my turbo has a brand new wastegate actuator on it, not sure if it a Greddy replacement or something better.
Last edited by 9krpmrx8; 08-22-2011 at 01:47 PM. Reason: spelling