Mazsport Ignition Solution!
#778
QS, has anyone gone into the dealership with this mod, and been denied service. Would you be able to disconnect this, and reconnect to the stock ignition if you were going in for service. Sorry for the noobish qs.
#779
B.I.G
iTrader: (4)
Join Date: Aug 2007
Location: AT---EIL
Posts: 1,401
Likes: 0
Received 0 Likes
on
0 Posts
umm i see whyt hey wouldnt service your vehicle..
but it depends what dealership you go to and how cool they are on mods.. I have some mods on miine and have never been denied service..
but when i doubt disconnect and go in. it should be just as simpel to disconnect.. but remember how to do those steps backwards
=]
but it depends what dealership you go to and how cool they are on mods.. I have some mods on miine and have never been denied service..
but when i doubt disconnect and go in. it should be just as simpel to disconnect.. but remember how to do those steps backwards
=]
#780
He's as bad as Can
The ignition system is a important part of this car. Installing a non Mazda ignition gives the dealer an easy out to engine related problems. I know about the Moss-Magnussen Act, but as with any law its just a bunch of words on paper. When it comes time to enforce it you will have a hard time. Switching back to the old coils can be done, but it will take some time so depending on how bad your car is you might not be able to do this. I don't have a warranty so that was not an issue with me.
#781
B.I.G
iTrader: (4)
Join Date: Aug 2007
Location: AT---EIL
Posts: 1,401
Likes: 0
Received 0 Likes
on
0 Posts
yea. some dealers jew us over. but the one i go to they are pretty cool.
they rebuilt my tranny even after i installed my ligthweight flywheel. no biggie.
I always stick to one service guy. i am a loyal customer so he takes care of me..
I go to ROGER BEASLY MAZDA IN AUSTIN TEXAS..
GREAT DEALER! even tho i baught my car in IL drove it all the way over here =]
they rebuilt my tranny even after i installed my ligthweight flywheel. no biggie.
I always stick to one service guy. i am a loyal customer so he takes care of me..
I go to ROGER BEASLY MAZDA IN AUSTIN TEXAS..
GREAT DEALER! even tho i baught my car in IL drove it all the way over here =]
#782
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
umm i see whyt hey wouldnt service your vehicle..
but it depends what dealership you go to and how cool they are on mods.. I have some mods on miine and have never been denied service..
but when i doubt disconnect and go in. it should be just as simpel to disconnect.. but remember how to do those steps backwards
=]
but it depends what dealership you go to and how cool they are on mods.. I have some mods on miine and have never been denied service..
but when i doubt disconnect and go in. it should be just as simpel to disconnect.. but remember how to do those steps backwards
=]
![Smilie](https://www.rx8club.com/images/smilies/smile.gif)
#783
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
Yeah, you could throw the stock one back in there without too much trouble. It would take a little time. This assumes you kept the bracket and old coils. Mine is pretty good and have never given me any hassle so far. The ignition system might be pushing it a little, but I think I could get mine to do it without too much trouble.
Last edited by Mazurfer; 03-18-2008 at 07:14 PM.
#787
B.I.G
iTrader: (4)
Join Date: Aug 2007
Location: AT---EIL
Posts: 1,401
Likes: 0
Received 0 Likes
on
0 Posts
yea thats what i mean. Just asking if anyone else has gotten thier coils in this week?
I didnt think i have to be so specific about it since we are talking about the mazsport ignition solution
DERRR
I didnt think i have to be so specific about it since we are talking about the mazsport ignition solution
DERRR
#788
Tailgaters beware
![Lol](https://www.rx8club.com/images/smilies/lol.gif)
Last edited by Rocketman1976; 03-18-2008 at 09:21 PM.
#789
Hit & Run Magnet
iTrader: (3)
my car is in for an oil change right now at arlington mazda. the guy (not my normal service person) was a bit leery on it, but i explained it and he seemed ok with it.
i wanted them to check all connections because my car had been running funny. it would get surges of power from 2k-3k rpm. like it wouldnt go smoothly, it would stay at 2k rpm for waay to long and then bam 1/4 second later it would be at 3k rpm.
i had to reset the cars computer, and i've heard driving can be funky after that. but we'll see how much rosenthal complains when i pick my car up.
i HOPE its just the cars computer.
i wanted them to check all connections because my car had been running funny. it would get surges of power from 2k-3k rpm. like it wouldnt go smoothly, it would stay at 2k rpm for waay to long and then bam 1/4 second later it would be at 3k rpm.
i had to reset the cars computer, and i've heard driving can be funky after that. but we'll see how much rosenthal complains when i pick my car up.
i HOPE its just the cars computer.
#791
Trouble Codes
Brettus, Did you get the codes back after a longer drive cycle?
#793
I am guessing mazsport did not test the ignition solution on JDM RX-8 and these CEL trouble codes could be specific to JDM RHD RX-8s. However, the car runs better then it did with stock coils and I can definitely feel the power gain.
#794
B.I.G
iTrader: (4)
Join Date: Aug 2007
Location: AT---EIL
Posts: 1,401
Likes: 0
Received 0 Likes
on
0 Posts
my car is in for an oil change right now at arlington mazda. the guy (not my normal service person) was a bit leery on it, but i explained it and he seemed ok with it.
i wanted them to check all connections because my car had been running funny. it would get surges of power from 2k-3k rpm. like it wouldnt go smoothly, it would stay at 2k rpm for waay to long and then bam 1/4 second later it would be at 3k rpm.
i had to reset the cars computer, and i've heard driving can be funky after that. but we'll see how much rosenthal complains when i pick my car up.
i HOPE its just the cars computer.
i wanted them to check all connections because my car had been running funny. it would get surges of power from 2k-3k rpm. like it wouldnt go smoothly, it would stay at 2k rpm for waay to long and then bam 1/4 second later it would be at 3k rpm.
i had to reset the cars computer, and i've heard driving can be funky after that. but we'll see how much rosenthal complains when i pick my car up.
i HOPE its just the cars computer.
My car is in for a checking of the brakes.. they have begun to schueel in the morning.. but after they warm up ima get them checked..
I told them about the flash update that i heard about and they are gonna see to it =]]
my car (sometimes) take more than the normal cranking over not just in the mornings this also occurs in the afternoon anytime basically.
hmm the only hesitation i find it in the upper rpms it improved when i got my spark plugs.. but its still there.
sooo hopefully the ignition solution will help.. but still waiting..
Hmmm those CEL lights.. are both of you alls cars JDM RHD?
#795
Tailgaters beware
It's pretty crazy that you are throwing a bunch of codes but it still feels like it runs better...
#796
Boosted Kiwi
iTrader: (2)
Just installed mazsport ignition solution on my JDM (right-hand drive) RX-8 and I am having the same problem Brettus had. The trouble codes come back on even after they are cleared. But the car runs perfectly. I have checked all the wiring and its as per the instructions.
Brettus, Did you get the codes back after a longer drive cycle?
Brettus, Did you get the codes back after a longer drive cycle?
a_ahlan - did you get the same codes as me - 351 , 352 , 353 & 354 ?
Waiting to hear from Scott as to what the codes are as they are not in the manual .
Last edited by Brettus; 03-19-2008 at 11:50 AM.
#797
I've figured out that when you clear the code it pretty much imediately comes back into "codes pending" . The Cel only comes on after a few drive cycles - ie you can drive for a while without the cel coming on after clearing it but once you shut off the engine and re-start it will come back on again .
a_ahlan - did you get the same codes as me - 351 , 352 , 353 & 354 ?
Waiting to hear from Scott as to what the codes are as they are not in the manual .
a_ahlan - did you get the same codes as me - 351 , 352 , 353 & 354 ?
Waiting to hear from Scott as to what the codes are as they are not in the manual .
351- Coil 1
352- Coil 2
353- Coil 3
354- Coil 4
when I cleared the code it pretty much imediately came back into "codes pending" . The Cel only comes on after a few drive cycles.
I am going to check the wiring one more time by doing the following -
Disconnect the mazsport harness labeled "1" from the factory (car's) wiring harness and start the car. Then check L1 spark plug if the spark stopped. This is the only way we can verify if the mazsport coil 1 (no. 1 from the front of the car) is conected to L1 of the factory harness.
If Scott does not give us a solution soon, we might just have to learn to live with the codes.
#798
#799
#800
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
Ditto.....that's the path I was trying to go down with Brettus when he fisrt posted about CEL issues. I assume he and Scott will get it all worked out now.....if that's truly the case.
![Dunno](https://www.rx8club.com/images/smilies/dunno.gif)