ShellDude's 4AT to 6 MT Turbo Thread
#26
weeeeeeeeee
Thread Starter
iTrader: (12)
Some things in the works:
Will retain stock ECU, suppress the TCM U0101 code with the AP, and run APV and P2s directly off the Adaptronic. Plan is to have this done by end of Summer.
- 6 Port + 6MT transmission swap
- Clutch Kit
- Shift ****
Will retain stock ECU, suppress the TCM U0101 code with the AP, and run APV and P2s directly off the Adaptronic. Plan is to have this done by end of Summer.
#27
Car Dude
Join Date: Nov 2011
Location: Portland, Texas
Posts: 298
Likes: 0
Received 0 Likes
on
0 Posts
The one regret I have about buying my boy his R3 is the limitations on readily available easy ecu tuning options. C'est la vie. *shrugs*
Good luck with the sale.
#31
Administrator
iTrader: (7)
#33
FULLY SEMI AUTOMATIC
iTrader: (9)
sucks to hear your 4 port is dead, after all that work and multiple snails you were making just a little more hp than my n/a 6 port. lol sorry buddy i had to. gl with the swap. is your normal shop doing it, idk if i should bring up the name. why not go re(w)?
#35
FULLY SEMI AUTOMATIC
iTrader: (9)
#36
weeeeeeeeee
Thread Starter
iTrader: (12)
yeah, normal shop ... he's doing the rebuild of the 6MT I ordered today too. Will likely not end up with much left of the 4 port block itself when all is said and done. shop has already offered to buy it anyway.
Last edited by ShellDude; 11-05-2014 at 06:45 PM.
#37
weeeeeeeeee
Thread Starter
iTrader: (12)
Parts acquired (in addition to the motor/trans above):
-New T618Z (moving existing water jacket + WG actuator to it)
-Clutch pedal assembly
-Internal shift boot / seals / ****
-MT steering wheel (portions used to replace paddles)
-MT gauge cluster
-CF drive shaft
-SS undertray
-SS oil cooler lines
-6MT engine harness
-Master Cylinder
Basic Plan:
Use my Adaptronic's extra pigtail to control the P2 injectors and the APV.
MEP will suppress the TCM CEL that's going to get thrown by my 4AT ECU.
Ignition wired / spliced to starter (bypass neutral)
Stock P1s - 4 port Secondaries in P2 and ID1000s in Secondaries
Live without cruise control
-New T618Z (moving existing water jacket + WG actuator to it)
-Clutch pedal assembly
-Internal shift boot / seals / ****
-MT steering wheel (portions used to replace paddles)
-MT gauge cluster
-CF drive shaft
-SS undertray
-SS oil cooler lines
-6MT engine harness
-Master Cylinder
Basic Plan:
Use my Adaptronic's extra pigtail to control the P2 injectors and the APV.
MEP will suppress the TCM CEL that's going to get thrown by my 4AT ECU.
Ignition wired / spliced to starter (bypass neutral)
Stock P1s - 4 port Secondaries in P2 and ID1000s in Secondaries
Live without cruise control
#41
weeeeeeeeee
Thread Starter
iTrader: (12)
the 4 port never made much over 230 boosted ... I think I have a dynosheet showing 235 at one point.
Progress being made.... rebuild of new to me motor is done. going in with the 6MT transmission next week.
Speed1 is doing the rebuild / install. I'll be swinging over to do the final tuning once ready.... looking like another week or two.
Progress being made.... rebuild of new to me motor is done. going in with the 6MT transmission next week.
Speed1 is doing the rebuild / install. I'll be swinging over to do the final tuning once ready.... looking like another week or two.
#43
weeeeeeeeee
Thread Starter
iTrader: (12)
Had to pick up a new clutch plate too... the one on the eBay motor was toast. I'm starting to get anxious.
-----
Unrelated I got a PM from someone who as the ability to send PMs to full inboxes and rather than go thru the BS to clean out my inbox (yup -- still protesting the lame limits here) I'll just reply here:
Rear Sub Reference
Posts 32 thru 37 here show all you need for tapping into the low power speaker signals for the rear amp: https://www.rx8club.com/series-i-do-...e2/#post252129
I did ground right to the body in the rear and ran a beefy (6 gauge) lead directly from the battery (with a nice fuse immediately after the battery) to the trunk thru the firewall and door channel. I used the center console power outlet for triggering accessory (key on / key off).
I had the box custom built one afternoon at a local car audio shop utilizing the sunken cargo area. You'll need a shallow sub if you go this route.
-----
Unrelated I got a PM from someone who as the ability to send PMs to full inboxes and rather than go thru the BS to clean out my inbox (yup -- still protesting the lame limits here) I'll just reply here:
Rear Sub Reference
Posts 32 thru 37 here show all you need for tapping into the low power speaker signals for the rear amp: https://www.rx8club.com/series-i-do-...e2/#post252129
I did ground right to the body in the rear and ran a beefy (6 gauge) lead directly from the battery (with a nice fuse immediately after the battery) to the trunk thru the firewall and door channel. I used the center console power outlet for triggering accessory (key on / key off).
I had the box custom built one afternoon at a local car audio shop utilizing the sunken cargo area. You'll need a shallow sub if you go this route.
#46
weeeeeeeeee
Thread Starter
iTrader: (12)
Another dilemma I have (just thought of this one a week ago) is that I've got the Griffin AT radiator that is now going to have an empty lower section because there'll be no ATF to keep cool.
I'm curious to see what this does to water temps in the new setup, if anything at all.
Another novel idea I had was to use it as a 3rd oil cooler.
I'm curious to see what this does to water temps in the new setup, if anything at all.
Another novel idea I had was to use it as a 3rd oil cooler.
#47
SARX Legend
iTrader: (46)
I doubt it will affect anything at all, a lot of the OEM style aftermarket replacement radiators from Calsonic/Koyo have the cooler integrated as they manufacture one radiator to fit in either the AT or the MT.
#48
Registered
iTrader: (25)
I was only looking at your injector remarks and suggesting what I perceive to be a simpler alternative. I haven't actually idled on the P2 injector position yet, but am not expecting any major problem with it. I would expect that firing an extra pair of injectors is maybe a bigger issue since you don't have that OE feature to begin with. Again, not familiar with any of these areas since mine is all OE 6-port from the get go ...
#49
weeeeeeeeee
Thread Starter
iTrader: (12)
Rebuilt 6 port motor is running. Threw a TPS position error after a couple drive cycles and went into limp mode. need to diagnose issue (going to try a different throttle body) but looking pretty good.
all injectors are firing (verified via Adaptronic WARI software) so once the TPS issue is solved I'll be able to get her on the dyno.
I'll be putting (already started) a bunch of **** up for sale in the classifieds.
Team, I do like your alternatives and they'd certainly work. The only thing you didn't address was opening the APV with 3A to 3P missing.
all injectors are firing (verified via Adaptronic WARI software) so once the TPS issue is solved I'll be able to get her on the dyno.
I'll be putting (already started) a bunch of **** up for sale in the classifieds.
Team, I do like your alternatives and they'd certainly work. The only thing you didn't address was opening the APV with 3A to 3P missing.
Last edited by ShellDude; 02-28-2015 at 03:39 AM.