SpeedForceRacing-326WHP with dyno chart
#1
TurboTim
Thread Starter
Join Date: Feb 2005
Location: San Diego
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
SpeedForceRacing-326WHP with dyno chart
We just finished our Black project car and we managed to get 326 at the wheels on a Dyno Dynamics.And 240 ft/lbs of torque to boot.Seehow flat the torque curve is Here is the dyno chart.
Last edited by SpeedForceRacing; 02-21-2006 at 08:08 PM.
#9
TurboTim
Thread Starter
Join Date: Feb 2005
Location: San Diego
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by nycgps
but as I can see in the picture, gotta relocate some of the stuff (battery, for example)
Hmm .... pretty costly, but ahh if it adds like more than 100 hp/tq .... I guess .. hmmm
Hmm .... pretty costly, but ahh if it adds like more than 100 hp/tq .... I guess .. hmmm
Last edited by SpeedForceRacing; 02-21-2006 at 08:24 PM.
#11
Normality is Obscene
Join Date: Aug 2003
Location: AL/GA...you pick
Posts: 1,053
Likes: 0
Received 0 Likes
on
0 Posts
headsnapper for sure...nice...just for kicks...why a non-ball bearing..i'm guessing a T04b?..those like lower oil pressures and less oiling...that the main reason?...or just it's overall scalability? I mean don't get me wrong..i think it's great i'm just wondering your reasons behind putting one in...
#12
Registered
Join Date: Aug 2004
Location: Virginia/Maryland
Posts: 1,294
Likes: 0
Received 0 Likes
on
0 Posts
$7500 seems like a lot to put out all at once, and no way I could have saved up enough to drop that kind of dough, but really I think its fairly reasonable. Assuming they're using a standalone EMS. If they're still using the emanage, then it is a bit expensive.
Over time I've spent over that on mods for my 8 and still don't have that kinda hp. If you look at turbo kits for other cars its really an average price for a good kit. The price of the Greddy turbo has just spoiled us. But I don't think the Greddy kit is as good quality as this kit, and definitely won't make this kinda power. Its my experience that if you want that kind of power, you're going to have to spend that kind of money (except maybe if you go the NOS route). Unless you own a Mustang and can get 20hp from a set of headers. But it all depends on what you want.
My only complaint is that its not a ball bearing turbo.
SFR could we get some more details about the turbo your using? What kind is it and what's the trim? Also, what kind of engine management are you using?
Over time I've spent over that on mods for my 8 and still don't have that kinda hp. If you look at turbo kits for other cars its really an average price for a good kit. The price of the Greddy turbo has just spoiled us. But I don't think the Greddy kit is as good quality as this kit, and definitely won't make this kinda power. Its my experience that if you want that kind of power, you're going to have to spend that kind of money (except maybe if you go the NOS route). Unless you own a Mustang and can get 20hp from a set of headers. But it all depends on what you want.
My only complaint is that its not a ball bearing turbo.
SFR could we get some more details about the turbo your using? What kind is it and what's the trim? Also, what kind of engine management are you using?
Last edited by rkostolni; 02-21-2006 at 10:28 PM.
#13
Registered User
doesn't the car rev to 9k+ rpm? You seem to be missing ~1150 RPM
Detonation or just lifted early?
EDIT: Just realized this was a with a picture and that the question was answered already.
Detonation or just lifted early?
EDIT: Just realized this was a with a picture and that the question was answered already.
Last edited by AlexCisneros; 02-21-2006 at 10:35 PM.
#14
TurboTim
Thread Starter
Join Date: Feb 2005
Location: San Diego
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rkostolni
SFR could we get some more details about the turbo your using? What kind is it and what's the trim? Also, what kind of engine management are you using?
It is a Turbonetics turbo. TO4E with a 57 trim. The hotside specs is our little secret The engine management is from Injection Perfection and it is basically a TSI unit.The same thing Ric Shaw uses.It controls timing,fuel,boost,it can control NOS,etc....It controls the injectors and ignition timing directly without using the Mass-air sensor to do your fueling corrections.It has a 22 psi MAP sensor in it for accurate pressure measurements.Very nice system and it is as close to stand alone as you can get without having to build a harness,rewire the car,etc.......
Because it does so much , it costs alot which is why the price ofthe turbo kit is up there.But hey if you want to run your own EMS system and figure out your fueling requirements, then you can save alot of money and buy a tuner kit.
#17
Follower of CHRIST!!!!!!!
Join Date: Aug 2004
Location: Planet Earth
Posts: 3,241
Likes: 0
Received 0 Likes
on
0 Posts
Dang nice gains. Do you planning to take that 8 to a track...it wold be cool for the customer to not only see a dyno but the real world application on a track. Just...so we could hear and see what those numbers could do.
By the way, anyone know what type of whp Adrian-1 is hitting? He just got a 13.1 in the 1/4 mile and we could use his greddy turbo to estimate/guestimate what the SFR Turbo could do.
By the way, anyone know what type of whp Adrian-1 is hitting? He just got a 13.1 in the 1/4 mile and we could use his greddy turbo to estimate/guestimate what the SFR Turbo could do.
#18
#1 Legend
iTrader: (1)
Join Date: May 2004
Location: TEXAS
Posts: 3,904
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rx8wannahave
we could use his greddy turbo to estimate/guestimate what the SFR Turbo could do.
OR... just for kicks, you could use this
http://www.rx7.com/accel_calculator.html
-hS
#19
Follower of CHRIST!!!!!!!
Join Date: Aug 2004
Location: Planet Earth
Posts: 3,241
Likes: 0
Received 0 Likes
on
0 Posts
Cool...that looks pretty fun, now is that whp or flywheel?
...and what do they mean shifts vs gear?
Like...how many shifts to 60mph and what gear....I don't understand that part??
...and what do they mean shifts vs gear?
Like...how many shifts to 60mph and what gear....I don't understand that part??
Last edited by rx8wannahave; 02-22-2006 at 08:06 PM.
#21
Storm Trooper
Join Date: May 2004
Location: Freakmont, CA
Posts: 3,908
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BigOLundh
There are so many different variables involved... i would think its just better to wait till an SFR turbo kit owner shows 1/4 mile times.
OR... just for kicks, you could use this
http://www.rx7.com/accel_calculator.html
-hS
OR... just for kicks, you could use this
http://www.rx7.com/accel_calculator.html
-hS
#22
Registered
Join Date: Aug 2004
Location: Virginia/Maryland
Posts: 1,294
Likes: 0
Received 0 Likes
on
0 Posts
Ya, but there's things that can be done to help with that. Stickier tires would be the biggest. Vivid also makes some traction bars, but I don't know how well they work.
#23
Yes, I am a novice in rotary engine technology...
I don't understand why the HP/Torque peaks at 7200 and then peters out...
So really, from 7200 to 9500 is pretty much useless.... is this correct?
They've turned our rotary into "acting like" a piston engine,
except there's no appreciable grunt off the line...
I don't get it (stupid is as stupid does)?!
I don't understand why the HP/Torque peaks at 7200 and then peters out...
So really, from 7200 to 9500 is pretty much useless.... is this correct?
They've turned our rotary into "acting like" a piston engine,
except there's no appreciable grunt off the line...
I don't get it (stupid is as stupid does)?!