Turbo RX8 video
#1
SIGSEGV
Thread Starter
Join Date: Feb 2003
Location: San Francisco, CA
Posts: 237
Likes: 0
Received 0 Likes
on
0 Posts
Turbo RX8 video
http://www.youtube.com/watch?v=pn62nbokoG4
and
http://www.youtube.com/watch?v=KeWVkdAni_0
Things left to do still is:
Install new seats
Install 8pot brembos
Install lower controller arm ball joint (defect)
Install new suspension
And considering HKS DLI-II
So, the videos are taken after a manual throttle body was installed. He's doing a base tune map since i have to break in the new rotary internal parts (not a motor swap).
So, in about 2 weeks, I'll have the car done (hopefully) after breakin and **hopefully** a video to go along w/ the power tune and dyno run.
Alex
and
http://www.youtube.com/watch?v=KeWVkdAni_0
Things left to do still is:
Install new seats
Install 8pot brembos
Install lower controller arm ball joint (defect)
Install new suspension
And considering HKS DLI-II
So, the videos are taken after a manual throttle body was installed. He's doing a base tune map since i have to break in the new rotary internal parts (not a motor swap).
So, in about 2 weeks, I'll have the car done (hopefully) after breakin and **hopefully** a video to go along w/ the power tune and dyno run.
Alex
#6
Read to succeed please...
Join Date: May 2006
Location: QC, NC
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
and I assume ours comes stock with the motor?
I didn't know there was an other way to do it except with cables... what are the advantages and disadvatages of each (if anyone cares to enlighten me and it hasn't already been discussed at length on the board someplace...)...
thanks for your patience...
I didn't know there was an other way to do it except with cables... what are the advantages and disadvatages of each (if anyone cares to enlighten me and it hasn't already been discussed at length on the board someplace...)...
thanks for your patience...
#7
SIGSEGV
Thread Starter
Join Date: Feb 2003
Location: San Francisco, CA
Posts: 237
Likes: 0
Received 0 Likes
on
0 Posts
i went w/ the manual throttle cable and not the stock drive by wire (not a throttle cable) because i felt when I was revving the car, there was this odd delay, enough for me to notice it. That was mainly the reason.
#13
Shink'd Out for 2006
Join Date: Apr 2006
Location: Morris Plains, NJ
Posts: 503
Likes: 0
Received 0 Likes
on
0 Posts
Staggered Racing Hart CX's and MS Nose very nice... You might want to list all your mods so people know what they are looking at. Congrats...
Im holding off for PTP turbo but I appreciate your finely tuned Greddy beast!!
Time
Im holding off for PTP turbo but I appreciate your finely tuned Greddy beast!!
Time
#14
SIGSEGV
Thread Starter
Join Date: Feb 2003
Location: San Francisco, CA
Posts: 237
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Moostafa29
^Arm+Leg+LONG time w/o car
Here's my modlist, i just edited my vbGarage:
https://www.rx8club.com/vbgarage.php?do=view&id=1372
As far as the DLI-II goes, its on the hksusa site and I know of an IS owner who has the DLI-II but w/ a universal harness.
#15
SIGSEGV
Thread Starter
Join Date: Feb 2003
Location: San Francisco, CA
Posts: 237
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by time4akshun
Staggered Racing Hart CX's and MS Nose very nice... You might want to list all your mods so people know what they are looking at. Congrats...
Im holding off for PTP turbo but I appreciate your finely tuned Greddy beast!!
Time
Im holding off for PTP turbo but I appreciate your finely tuned Greddy beast!!
Time
#16
RX8 HA HA
Originally Posted by Moostafa29
I haven't heard of anyone in the states actually having it.
#18
Registered
Join Date: Aug 2004
Location: Virginia/Maryland
Posts: 1,294
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by alex
base power range is 350whp, for a dyno chart show, somewhere above 400whp.
#19
Storm Trooper
Join Date: May 2004
Location: Freakmont, CA
Posts: 3,908
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rkostolni
Unless I'm missing something, I think you'll be disappointed. The Greddy turbo maxes out at just over 300whp.
#20
Registered
Join Date: Aug 2004
Location: Virginia/Maryland
Posts: 1,294
Likes: 0
Received 0 Likes
on
0 Posts
I'm pretty confident that the Greddy turbo can't flow enough lb/min to support 400whp though. Even if the motor is built for more, it won't do much with superheated air. The Puertoricans have already tried and found the limits to be around 300whp.
#21
SIGSEGV
Thread Starter
Join Date: Feb 2003
Location: San Francisco, CA
Posts: 237
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rkostolni
I'm pretty confident that the Greddy turbo can't flow enough lb/min to support 400whp though. Even if the motor is built for more, it won't do much with superheated air. The Puertoricans have already tried and found the limits to be around 300whp.
#22
SIGSEGV
Thread Starter
Join Date: Feb 2003
Location: San Francisco, CA
Posts: 237
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Moostafa29
Custom built engine. I think its ported with FD internals or something like that.
#23
SIGSEGV
Thread Starter
Join Date: Feb 2003
Location: San Francisco, CA
Posts: 237
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by IZoomZoomI
that's weird wouldn't the drive by wire increase throttle response?
#24
drivelinestore.com
Join Date: Jun 2005
Location: OC
Posts: 2,756
Likes: 0
Received 0 Likes
on
0 Posts
hey alex the guy in the video the guy whos recording he was talking to some guy that wasnt on the video not mr wakita. he sounds familiar. was his name "Katsu?" or or known as "KC"? iono just curious.