Dyno Results w hard data (On a known Dynojet)
#176
mostly harmless
Join Date: Jun 2002
Location: Greater Vancouver Area, BC
Posts: 3,440
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by banzairx7
The increase in torque could be linear after 6250, not a jump as you imply. Also any jump in torque in a vtec system is due to improperly timed cam switch or bad tuning. The whole purpose of vtec is to have a flat torque curve with no jumps or spiking
The increase in torque could be linear after 6250, not a jump as you imply. Also any jump in torque in a vtec system is due to improperly timed cam switch or bad tuning. The whole purpose of vtec is to have a flat torque curve with no jumps or spiking
Originally posted by StretchSJE
If the RX-8 is ONLY lacking power after 6250 RPM, that means it must have a 20ft-lbs jump after 6250RPM for that to be true. Highly unlikely. Think about that- that's larger than most any VTEC jump, and certainly wouldn't be "smooth" like the rotary is known for.
If the RX-8 is ONLY lacking power after 6250 RPM, that means it must have a 20ft-lbs jump after 6250RPM for that to be true. Highly unlikely. Think about that- that's larger than most any VTEC jump, and certainly wouldn't be "smooth" like the rotary is known for.
Last edited by wakeech; 08-19-2003 at 02:29 PM.
#178
The increase in torque could be linear after 6250, not a jump as you imply.
Even if it is linear, the engine spools up so quickly that a 20ft-lbs increase over 1500rpms would feel like a spike. 1500rpms for a rotary is like 800rpms in a normal piston motor- you'd get a 20ft-lbs increase in force in about half a second's time in first gear, even though on the dyno the increase would look linear.
...did you do the math?? and also, have you looked at the factory dynographs?? peak power comes right at redline, so the torque difference isn't 20ftlbs large, nor is there suppost to be a jump: the curve just isn't suppost to level off and turn down until 8500 rpm.
I'm not suggesting there should be a peak- quite the contrary. That's why I think the entire graph is reading low, which lends itself to the theory of the ECU only allowing ~90% throttle or something.
Last edited by StretchSJE; 08-19-2003 at 02:54 PM.
#179
mostly harmless
Join Date: Jun 2002
Location: Greater Vancouver Area, BC
Posts: 3,440
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by StretchSJE
To make 207whp at 8500rpm
To make 207whp at 8500rpm
#180
I thought you were some veteran here- crap, I've been reading your posts forever on this site. Peak power is claimed at 8500rpm- 9000rpm is redline.
In fact, this graph shows a pretty close torque curve match too discussed here.
In fact, this graph shows a pretty close torque curve match too discussed here.
#184
mostly harmless
Join Date: Jun 2002
Location: Greater Vancouver Area, BC
Posts: 3,440
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by StretchSJE
I thought you were some veteran here- crap, I've been reading your posts forever on this site.
I thought you were some veteran here- crap, I've been reading your posts forever on this site.
#185
Banned
Thread Starter
Join Date: Jun 2002
Location: Auburn, CA
Posts: 360
Likes: 0
Received 0 Likes
on
0 Posts
I edited my first post with new graph and data.
Completed new dyno runs today (9-3-2003) 10 degrees cooler and 10% more humidity.
Substantial increase in both horsepower & torque. I also did runs in fourth and fifth gear and they were within 1% of run 002.
Vince
Completed new dyno runs today (9-3-2003) 10 degrees cooler and 10% more humidity.
Substantial increase in both horsepower & torque. I also did runs in fourth and fifth gear and they were within 1% of run 002.
Vince
#191
Next time try 87 octane and maybe youll top this guy's run, which i think is the highest dyno weve seen yet. Youve got 2000 more miles so you should top him with 87.
https://www.rx8club.com/showthread.p...5&pagenumber=1
https://www.rx8club.com/showthread.p...5&pagenumber=1
#192
Well the good news is that you are making all the torque you should. I would think that your car should never ( unless modded obviously ) pull HARDER than that. But on the down side, the torque drops off a couple hundred RPMs early, so it's just not pulling strong as long as it should. It is looking better though and i do think there is an easy fix.
#193
Registered User
Join Date: Jul 2003
Location: Torrance, CA
Posts: 47
Likes: 0
Received 0 Likes
on
0 Posts
Very encouraging that an additional 2000 miles freed up that much power (did you change the oil in that timeframe?).
If it frees up another 10-12 hp you'll be very close to Mazda's 238 hp rating.
SC
If it frees up another 10-12 hp you'll be very close to Mazda's 238 hp rating.
SC
#194
Banned
Thread Starter
Join Date: Jun 2002
Location: Auburn, CA
Posts: 360
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by ChurchAutoTest
Very encouraging that an additional 2000 miles freed up that much power (did you change the oil in that timeframe?).
If it frees up another 10-12 hp you'll be very close to Mazda's 238 hp rating.
SC
Very encouraging that an additional 2000 miles freed up that much power (did you change the oil in that timeframe?).
If it frees up another 10-12 hp you'll be very close to Mazda's 238 hp rating.
SC
Vince
#198
Originally posted by aussie77
Hate to be a pain in the ***, but with the original data gone, can we get a quick summary comparing the two?
Ie, peak hp, torque, temperature, miles on the car?
Hate to be a pain in the ***, but with the original data gone, can we get a quick summary comparing the two?
Ie, peak hp, torque, temperature, miles on the car?
#200
Registered User
Join Date: Jul 2003
Location: Torrance, CA
Posts: 47
Likes: 0
Received 0 Likes
on
0 Posts
Interesting. Might be worth having other people recheck after an oil change. I do a lot of oil testing for several companies and we've found power differentials of up to 3-4% by changing from standard factory fills to high quality forumlated oils.
Maybe Mazda is using an unusual oil formulation for break in. On piston engines it usually has a high Moly content, but for rotaries I don't know.
SC
Maybe Mazda is using an unusual oil formulation for break in. On piston engines it usually has a high Moly content, but for rotaries I don't know.
SC
Originally posted by compaddict
Changed it right after the first dyno test.
Vince
Changed it right after the first dyno test.
Vince