Oil cooler thermostat?
#1
Ayrton Senna Forever
Thread Starter
Oil cooler thermostat?
Maybe it's already answered, but I found the next sentence in a German RX-8 (SE) service manual. I did not find this info in any other english serv. man.
If it means that there is a 194F opening temp thermostat valve in the oil coolers, maybe it could be the reason for some of the overheated engine, and the high oil temps.
Some thoughts:
There is no cell when this thermo valve goes wrong.
If the thermo valve open later (went wrong), the oil temp will be too high and the oil will be too thin (bearing wear).
Who knows when the thermo valve goes wrong, does it stay opened or closed mode?
In winter (europe) my oil coolers are only warm when the engine is on idle for a while and the car is standing. If the car was moving before, the coolers are cold immediate after stopping. I could check it with my hand after stopping. Even in summer my cooler's thermostats are closed a lot of times (checked after stopping), when the engine warm.
Ein integriertes Thermostatventil führt Öl mit einer Temperatur von über 90C (194F) durch den Ölkühler.
Some thoughts:
There is no cell when this thermo valve goes wrong.
If the thermo valve open later (went wrong), the oil temp will be too high and the oil will be too thin (bearing wear).
Who knows when the thermo valve goes wrong, does it stay opened or closed mode?
In winter (europe) my oil coolers are only warm when the engine is on idle for a while and the car is standing. If the car was moving before, the coolers are cold immediate after stopping. I could check it with my hand after stopping. Even in summer my cooler's thermostats are closed a lot of times (checked after stopping), when the engine warm.
#2
I don't buy Kool-Aid
Oh good find. However Rotarys run hot anyway. Always have.
You know Jeff (MM) can read that stuff (German) really good. PM him.
But why would it be in that book and not the US book???
Keep us posted!
You know Jeff (MM) can read that stuff (German) really good. PM him.
But why would it be in that book and not the US book???
Keep us posted!
#3
Ayrton Senna Forever
Thread Starter
MM's post box exceeded the limit, so I sent a mail to him.
Just for confidence, the information comes from the German Mazda RX-8 (SE) Trainingshandbuch 11/2003.
It's a book in my hands, but I don't speak German.
Just for confidence, the information comes from the German Mazda RX-8 (SE) Trainingshandbuch 11/2003.
It's a book in my hands, but I don't speak German.
Last edited by ayrton012; 02-26-2009 at 09:01 AM. Reason: uploading pdf
#8
Banned
iTrader: (3)
No, probably not.
His oil temps are never as high as his water temps when he begins to overheat.
I'm in the same boat. (Though my issues are due to the intercooler blocking airflow to the rad.)
Thermostats in the oil coolers is a good thing in most places, I would just like to see it open at 175°F.
His oil temps are never as high as his water temps when he begins to overheat.
I'm in the same boat. (Though my issues are due to the intercooler blocking airflow to the rad.)
Thermostats in the oil coolers is a good thing in most places, I would just like to see it open at 175°F.
#14
Registered
iTrader: (3)
thats why you should pay more attention to the coolant temps---and if you get it down the oil temp will follow!
Oil doesnt play a part in cooling a large part of the engine whereas the coolant does---concentrate on the coolant. If you concentrate on just the oil---well ok go ahead.
olddragger
Oil doesnt play a part in cooling a large part of the engine whereas the coolant does---concentrate on the coolant. If you concentrate on just the oil---well ok go ahead.
olddragger
#16
Registered User
Join Date: Sep 2004
Location: Rohnert Park CA
Posts: 755
Likes: 0
Received 0 Likes
on
0 Posts
FC oil cooler thermostats started opening at between 140F and 149F (60-65C), the same temp that the E-shaft thermo pellet opened on a FC.
#17
Registered User
Join Date: Sep 2004
Location: Rohnert Park CA
Posts: 755
Likes: 0
Received 0 Likes
on
0 Posts
thats why you should pay more attention to the coolant temps---and if you get it down the oil temp will follow!
Oil doesnt play a part in cooling a large part of the engine whereas the coolant does---concentrate on the coolant. If you concentrate on just the oil---well ok go ahead.
olddragger
Oil doesnt play a part in cooling a large part of the engine whereas the coolant does---concentrate on the coolant. If you concentrate on just the oil---well ok go ahead.
olddragger
#19
Registered
iTrader: (3)
if the oil is doing 30 % of the cooling then the coolant is doing 70%. which do you think will respond to upgrades better? which will have the most influence on the other?
to see one difference between the engines look at the housings on the earlier models versus the renasis and you will see that the areas around the sparkplugs has a much bigger area for coolant to pass through for example.
the twin oil coolers on the rx8 are pretty good--the oil system has the capacity to cool the oil if it is not asked to cool more than its share. The inadequate coolant system does just that. The coolant temps on a 90+ day on an oem car at low speed can get to 230F easily. the oil will be at around 210F. To get the oil temps down from that you are going to have to create enough cooling capacity to influence the coolant temps--that will be a pretty big job. Now if you add just a little coolant cooling capacity to bring that temp down to 200--then the oil will drop down to 180 easily.
would you rather work on the system that has the lesser impact on the result you are seeking?
And dont forget--the oil will do its job at 250F+ coolant will not!
It does have to be a balance--you dont want much difference between the two.
enough said.
olddragger
to see one difference between the engines look at the housings on the earlier models versus the renasis and you will see that the areas around the sparkplugs has a much bigger area for coolant to pass through for example.
the twin oil coolers on the rx8 are pretty good--the oil system has the capacity to cool the oil if it is not asked to cool more than its share. The inadequate coolant system does just that. The coolant temps on a 90+ day on an oem car at low speed can get to 230F easily. the oil will be at around 210F. To get the oil temps down from that you are going to have to create enough cooling capacity to influence the coolant temps--that will be a pretty big job. Now if you add just a little coolant cooling capacity to bring that temp down to 200--then the oil will drop down to 180 easily.
would you rather work on the system that has the lesser impact on the result you are seeking?
And dont forget--the oil will do its job at 250F+ coolant will not!
It does have to be a balance--you dont want much difference between the two.
enough said.
olddragger
#20
Registered User
Join Date: Sep 2004
Location: Rohnert Park CA
Posts: 755
Likes: 0
Received 0 Likes
on
0 Posts
if the oil is doing 30 % of the cooling then the coolant is doing 70%. which do you think will respond to upgrades better? which will have the most influence on the other?
to see one difference between the engines look at the housings on the earlier models versus the renasis and you will see that the areas around the sparkplugs has a much bigger area for coolant to pass through for example.
the twin oil coolers on the rx8 are pretty good--the oil system has the capacity to cool the oil if it is not asked to cool more than its share. The inadequate coolant system does just that. The coolant temps on a 90+ day on an oem car at low speed can get to 230F easily. the oil will be at around 210F. To get the oil temps down from that you are going to have to create enough cooling capacity to influence the coolant temps--that will be a pretty big job. Now if you add just a little coolant cooling capacity to bring that temp down to 200--then the oil will drop down to 180 easily.
would you rather work on the system that has the lesser impact on the result you are seeking?
And dont forget--the oil will do its job at 250F+ coolant will not!
It does have to be a balance--you dont want much difference between the two.
enough said.
olddragger
to see one difference between the engines look at the housings on the earlier models versus the renasis and you will see that the areas around the sparkplugs has a much bigger area for coolant to pass through for example.
the twin oil coolers on the rx8 are pretty good--the oil system has the capacity to cool the oil if it is not asked to cool more than its share. The inadequate coolant system does just that. The coolant temps on a 90+ day on an oem car at low speed can get to 230F easily. the oil will be at around 210F. To get the oil temps down from that you are going to have to create enough cooling capacity to influence the coolant temps--that will be a pretty big job. Now if you add just a little coolant cooling capacity to bring that temp down to 200--then the oil will drop down to 180 easily.
would you rather work on the system that has the lesser impact on the result you are seeking?
And dont forget--the oil will do its job at 250F+ coolant will not!
It does have to be a balance--you dont want much difference between the two.
enough said.
olddragger
However it makes no sense what so ever to say, "I only want to upgrade the radiator" if you are having temp issues. If you are having temp issues you should look at every thing you can, to help.
Its not like changing the oil cooler thermostat and eshaft thermo valve is going to solve anything, but in conjunction with other modifications it may lead to better coolant, oil and engine life. Now with a piston engine, the oil does not provide even 5% of the cooling, so your comments fit that idea perfect. Why waste the time even looking at oil cooling if you are not affecting anything. On piston engines that use an oil cooler, it is more for oil life than cooling of the engine.
But on a rotary, its not, and this is not a one thing or another issue. Sure if you can solve the issue with a bigger 3 row radiator, then you are done. But if not, if you run the oil temp back down at 180 instead of 210, that might be the extra kick that helps.
Now again, don't get me wrong. If you are having overheating issues, just changing the oil cooler thermostat is not going to solve anything...But how much less viscosity and oil break down.. how much would be reduced by dropping that oil 10 or 20 degrees?
#22
I don't buy Kool-Aid
Hey guys, I asked this before but no one really gave me an answer, What about using a water or oil pool? will that help with cooling? I know some GT and other race cars use them.
-Gil
-Gil
#23
Registered
iTrader: (3)
icemark--you are absolutely correct--everything should be looked at. And the full range balance (warm up, wot applications etc) between the oil temps and the coolant temps have to be considered.
In looking at all --i found my solution by simply adding a small secondary radiator placed below the front support member directly in the air flow
https://www.rx8club.com/attachment.p...1&d=1235846259
see pic--this little thing with a couple of other mods will fix the cooling problem(except for the desert guys with no humidity in the air.
olddragger
In looking at all --i found my solution by simply adding a small secondary radiator placed below the front support member directly in the air flow
https://www.rx8club.com/attachment.p...1&d=1235846259
see pic--this little thing with a couple of other mods will fix the cooling problem(except for the desert guys with no humidity in the air.
olddragger
#25
Momentum Keeps Me Going
....see pic--this little thing with a couple of other mods will fix the cooling problem(except for the desert guys with no humidity in the air.
olddragger
olddragger