What are my choices for obdII/can scan tool ?
#28
peterisurhero
Join Date: Mar 2006
Location: cerritos, CA
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jzief128
Does anyone have the Harrison CanScan for PDA? I am interested in going that route and getting a PDA, since I don't want to spring for a new laptop.
me too man. i juss want a scanylizer for a pda
#29
Power!!
Well for all that are interested I ended up going with the AutoEngineuity tool. There was a person on this site selling one used so I picked it up for a discount. So in the end it was the cheaper tool to buy and still has some nice features like the real time data logging and the virtual dyno. I haven't had a chance to play with it yet but I will let people know my feedback when I am able. I'm hopefully going to be able to pull my CEL codes tonight and do a little data logging.
#30
Power!!
Alright I got my canscan tool! I plugged it in and pulled my MIL codes! I have code P0336! Woohoo!...oh crap I have a MIL code. Okay so I looked it up and it means:
P0336 Eccentric shaft position sensor circuit range/performance problem
ON 1 CCM ´ (See DTC P0336 )
So anyone have any ideas how I'd need to fix it? I looked around on the forum and didn't find any explaination. Is this an indication that I need to replace my ignition coils with the upgraded parts? If someone has a manual where they'd be willing to look up the resolution I'd appreciate it.
Here's my MIL report:
Diagnostic Trouble Codes
P0336 Crankshaft Position Sensor A Circuit Range/Performance
Freeze Frame (Frame 0) for DTC P0336
Absolute Load Value: 64 % Absolute Throttle Position B: 32 %
Absolute Throttle Position D: 32 % Absolute Throttle Position E: 21 %
Absolute Throttle Position: 15 % Air Flow Rate From Mass Air Flow Sensor: 1.15 lb/min
Ambient Air Temperature: 63 F Calculated Load: 99 %
Commanded Equivalence Ratio: 0.996 Lam Commanded Throttle Actuator Control: 6 %
Control Module Voltage: 12.48 V Coolant Temperature: 199 F
Engine RPM: 166 r/min Fuel System Status Bank One: Open (Driving Conditions)
Fuel System Status Bank Two: Not Reported Ignition Timing Advance for #1: -5.0 deg
Intake Air Temperature: 68 F Long Term Fuel Trim Bank One: 2.34 %
Relative Throttle Position: 4 % Short Term Fuel Trim Bank One: 0.00 %
P0336 Eccentric shaft position sensor circuit range/performance problem
ON 1 CCM ´ (See DTC P0336 )
So anyone have any ideas how I'd need to fix it? I looked around on the forum and didn't find any explaination. Is this an indication that I need to replace my ignition coils with the upgraded parts? If someone has a manual where they'd be willing to look up the resolution I'd appreciate it.
Here's my MIL report:
Diagnostic Trouble Codes
P0336 Crankshaft Position Sensor A Circuit Range/Performance
Freeze Frame (Frame 0) for DTC P0336
Absolute Load Value: 64 % Absolute Throttle Position B: 32 %
Absolute Throttle Position D: 32 % Absolute Throttle Position E: 21 %
Absolute Throttle Position: 15 % Air Flow Rate From Mass Air Flow Sensor: 1.15 lb/min
Ambient Air Temperature: 63 F Calculated Load: 99 %
Commanded Equivalence Ratio: 0.996 Lam Commanded Throttle Actuator Control: 6 %
Control Module Voltage: 12.48 V Coolant Temperature: 199 F
Engine RPM: 166 r/min Fuel System Status Bank One: Open (Driving Conditions)
Fuel System Status Bank Two: Not Reported Ignition Timing Advance for #1: -5.0 deg
Intake Air Temperature: 68 F Long Term Fuel Trim Bank One: 2.34 %
Relative Throttle Position: 4 % Short Term Fuel Trim Bank One: 0.00 %
#32
so...as far as scanners for CAN with CEL check and reset and data, these are the options? did i miss any?
Auterra Scan Tool - http://www.auterraweb.com/
AutoEnginuity ScanTool - http://www.autoenginuity.com/products-scantoolpc.html
Harrison R&D OBDScan-Apex - http://www.obdscan.net/APEX.htm
Harrison R&D CANScan-USB - http://www.obdscan.net/canscan_new.htm
Harrison R&D CANScan-RS232 - http://www.obdscan.net/canscan.htm
Hymee sCANalyser - http://www.performancedesign.com.au/?content=scanalyser
Auterra Scan Tool - http://www.auterraweb.com/
AutoEnginuity ScanTool - http://www.autoenginuity.com/products-scantoolpc.html
Harrison R&D OBDScan-Apex - http://www.obdscan.net/APEX.htm
Harrison R&D CANScan-USB - http://www.obdscan.net/canscan_new.htm
Harrison R&D CANScan-RS232 - http://www.obdscan.net/canscan.htm
Hymee sCANalyser - http://www.performancedesign.com.au/?content=scanalyser
#35
Administrator
iTrader: (7)
back from the dead!
I REALLY like the interface of the Scanalyzer, just bummed out it won't work on a PDA.
I had plans to mount the PDA to the right of the radio controls (there's a circular pull out there) but then I realized it wouldn't work. Hmmm....decisions, decisions.
I REALLY like the interface of the Scanalyzer, just bummed out it won't work on a PDA.
I had plans to mount the PDA to the right of the radio controls (there's a circular pull out there) but then I realized it wouldn't work. Hmmm....decisions, decisions.
#36
Power!!
#38
bringing this thread back.
I would like to buy a good logging toll for my rx8. after searching I narrowed my choices down to these 3:
Harrison OBDScan-APEX http://www.obdscan.net/RX8_PGM.htm
Hymee sCANalyser Live USB http://www.performancedesign.com.au/...yser_live.html
AutoEnginuity's Scan Tool http://www.autoenginuity.com/products.html
which one is the best for high speed logging of various engine parameters?
I would like to buy a good logging toll for my rx8. after searching I narrowed my choices down to these 3:
Harrison OBDScan-APEX http://www.obdscan.net/RX8_PGM.htm
Hymee sCANalyser Live USB http://www.performancedesign.com.au/...yser_live.html
AutoEnginuity's Scan Tool http://www.autoenginuity.com/products.html
which one is the best for high speed logging of various engine parameters?
Thread
Thread Starter
Forum
Replies
Last Post
GranTouTou
Series I Wheels, Tires, Brakes & Suspension
0
09-30-2015 06:11 AM