My Rebuild wont Start any Ideas?
#1
Registered User
Thread Starter
Join Date: Jul 2012
Location: Calgary, AB
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
My Rebuild wont Start any Ideas?
Just had my engine rebuilt at a very reputable shop here in Calgary, AB. Dropped it in connected everything turned it over with no gas or spark to build oil pressure. reconnected Spark and Gas. This is what I'm getting:
https://www.youtube.com/watch?v=k2UQ...e_gdata_player
any Ideas?
If you have any questions let me know I will update.
Thanks yall
P.S. I'm a little new to the forum, please don't burn me. I am mechanically inclined but the rotary is a little new to me.
https://www.youtube.com/watch?v=k2UQ...e_gdata_player
any Ideas?
If you have any questions let me know I will update.
Thanks yall
P.S. I'm a little new to the forum, please don't burn me. I am mechanically inclined but the rotary is a little new to me.
#2
Registered
Pull the ecu leads from the coils.
Pull the fuel breakers from the under hood "fuze" center.
Remove the oil filter.
Spin the engine until oil comes out of the oil filter mount location.
Connect everything back, try starting again.
Pull the fuel breakers from the under hood "fuze" center.
Remove the oil filter.
Spin the engine until oil comes out of the oil filter mount location.
Connect everything back, try starting again.
#3
Modulated Moderator
iTrader: (3)
Calll Adam and ask him why it won't start
Confirm fuel pressure and spark...and then check that the plugs aren`t fouled from the assembly lube...make sure you have the coil and injector wiring correct....
Is the ESS hooked up?.....( that is the easiest way to crank it with no chance of starting it as well....to build oil pressure )
Check back later with more info
Confirm fuel pressure and spark...and then check that the plugs aren`t fouled from the assembly lube...make sure you have the coil and injector wiring correct....
Is the ESS hooked up?.....( that is the easiest way to crank it with no chance of starting it as well....to build oil pressure )
Check back later with more info
#5
Registered User
Thread Starter
Join Date: Jul 2012
Location: Calgary, AB
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Adam's not in yet Sent him an email I will be home at 6:15 to check everything I'll try your suggestions and let you know how it goes.
Any you from Calgary?
Any you from Calgary?
#6
Registered User
Thread Starter
Join Date: Jul 2012
Location: Calgary, AB
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Tried everything... eventually got a very bad Idle at 560RPM after a pull start...with no throttle response. It's going to Mazda to see if they have any ideas.
#8
As mentioned above; check your injector connections. They are probably in wrong locations. This is THE MOST COMMON mistake with Renesis installs.
I hope that helps.
Paul.
I hope that helps.
Paul.
#9
Registered User
Thread Starter
Join Date: Jul 2012
Location: Calgary, AB
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Official Diagnosis 2 blown ignition coils and a severely flooded half of engine. cost to diagnose, parts and labor...$400 official total for build so far including car $6800
Car w/ blown engine $1200
Rebuild w/ full depth seals and overlapped housings + lower compression (I think) $4661
Misc Fluids (Oil, coolant, trans fluid and dif Fluid) $200
Shift boot, console, pizza to bribe friends to help. $300
30hr of labour (boozing included) .... Priceless
Car w/ blown engine $1200
Rebuild w/ full depth seals and overlapped housings + lower compression (I think) $4661
Misc Fluids (Oil, coolant, trans fluid and dif Fluid) $200
Shift boot, console, pizza to bribe friends to help. $300
30hr of labour (boozing included) .... Priceless
#10
Registered User
Thread Starter
Join Date: Jul 2012
Location: Calgary, AB
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Hey got it back from Mazda they said there is a leak in the intake manifold and thus it cannot stay idling. real pain to drive because if the rpm get too low it kills the engine. Is Mazda correct or are they lying to me? It is also burning extremely rich.. this also caused by the leak?
"Checked fuel trim, +25% at idle, a large intake manifold leak is present"
Compression is Rotar #1 5.9, 5.9, 6.0 @260RPM #25.7, 5.8, 5.9@ 253RPM
"Checked fuel trim, +25% at idle, a large intake manifold leak is present"
Compression is Rotar #1 5.9, 5.9, 6.0 @260RPM #25.7, 5.8, 5.9@ 253RPM
#13
Registered User
Thread Starter
Join Date: Jul 2012
Location: Calgary, AB
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Sent an email to their operations manager for the miss and a few other thing that happened payment wise.
Thread
Thread Starter
Forum
Replies
Last Post