Got My AP Racing Brakes for the RX8!
#1
OldeSpeede, Inc.
Thread Starter
Join Date: Apr 2004
Location: Costa Mesa, CA
Posts: 307
Likes: 0
Received 0 Likes
on
0 Posts
![Thumbs up](https://www.rx8club.com/images/icons/icon14.gif)
Well, I finally got word that the kit was out and went down to STILLEN to pick up my AP Racing Kit! I still have stock wheels but have a bolt on spacer that will give me enough clearance for now until I upgrade to wheels with more brake clearance.
Here's a few shots after opening one of the boxes:
1. Full Box Shot - Everything in one of the two boxes for the kit (left and right)
2. Rotor and caliper face close up
3. Profile view of rotor and caliper, look how beefy that thing is
4. Mounting bracket for the caliper - Anodized aluminum with steel thread inserts
I also was surprised that everything was assembled (minus the lines being installed on the caliper. It looks like everything should be a simple remove and replace (brake bleeding will probably be the hardest part!
I planned to put the kit on this weekend, but might not have time (Chargers Playoff Game tomorrow!!!) I'll definitely post up picks once I do get it going.
Here's a few shots after opening one of the boxes:
1. Full Box Shot - Everything in one of the two boxes for the kit (left and right)
2. Rotor and caliper face close up
3. Profile view of rotor and caliper, look how beefy that thing is
4. Mounting bracket for the caliper - Anodized aluminum with steel thread inserts
I also was surprised that everything was assembled (minus the lines being installed on the caliper. It looks like everything should be a simple remove and replace (brake bleeding will probably be the hardest part!
I planned to put the kit on this weekend, but might not have time (Chargers Playoff Game tomorrow!!!) I'll definitely post up picks once I do get it going.
![Rock](https://www.rx8club.com/images/smilies/rock.gif)
#3
The forgestar be with you
Join Date: Jan 2006
Location: Miami, Florida
Posts: 1,237
Likes: 0
Received 0 Likes
on
0 Posts
Don't forget about the torque settings...I maid that mistake and snapped one of the caliper bolts.
1st set of Caliper bolts - 21 to 34 ft/lbs
Note: These are the bolts that you need to take off to get to the pads. I honestly dont remember the torque for the other bolts but if you search on the forum there is a site that has the Rx-8 shop manuel online.
Good wrenching!
1st set of Caliper bolts - 21 to 34 ft/lbs
Note: These are the bolts that you need to take off to get to the pads. I honestly dont remember the torque for the other bolts but if you search on the forum there is a site that has the Rx-8 shop manuel online.
Good wrenching!
![Ylsuper](https://www.rx8club.com/images/smilies/ylsuper.gif)
#11
OldeSpeede, Inc.
Thread Starter
Join Date: Apr 2004
Location: Costa Mesa, CA
Posts: 307
Likes: 0
Received 0 Likes
on
0 Posts
I will definitely post the weights. As far as the spacers, that is only temporary. Once I get new wheels they will be properly sized to accept the kit.
#13
Administrator
iTrader: (7)
grats on the BBK. it looks pretty hot! when are you planning on getting the new wheels?
#16
Absolute Rotary Madness
Join Date: Mar 2004
Location: Thessaloniki, Greece
Posts: 1,291
Likes: 0
Received 0 Likes
on
0 Posts
very nice, I'll get the same kit soon, due to financial reasons I postponed it... ap racing is, if not the best, one of the best brake companies out there.... re amemiya uses these for his cars too. I'd like to know the weights too and ...price please (if thats ok with you to tell)
do you know if they fit a +38 offset? thanks
do you know if they fit a +38 offset? thanks
Last edited by RotorManiac; 01-14-2007 at 02:58 PM.
#20
OldeSpeede, Inc.
Thread Starter
Join Date: Apr 2004
Location: Costa Mesa, CA
Posts: 307
Likes: 0
Received 0 Likes
on
0 Posts
Ok, I haven't installed them yet, but I did get weights for everyone:
AP Racing CP6600 Caliper with pads, mounting bracket and hardware: 9lbs
330mm 2 Piece Cross Drilled and Slotted Rotors: 17lbs
Also, the spacer I am currently using is a bolt on unit, so longer wheel studs are not necessary.
I will definitely post pictures of the install.
RotorManiac: The price of the kit is $2376.75 and you can check fitment with your wheels using the attached profile.
AP Racing CP6600 Caliper with pads, mounting bracket and hardware: 9lbs
330mm 2 Piece Cross Drilled and Slotted Rotors: 17lbs
Also, the spacer I am currently using is a bolt on unit, so longer wheel studs are not necessary.
I will definitely post pictures of the install.
RotorManiac: The price of the kit is $2376.75 and you can check fitment with your wheels using the attached profile.
![Smilie](https://www.rx8club.com/images/smilies/smile.gif)
#23
Absolute Rotary Madness
Join Date: Mar 2004
Location: Thessaloniki, Greece
Posts: 1,291
Likes: 0
Received 0 Likes
on
0 Posts
^can you be more specific? which bbk do you mean?
silverarrow, thanks, much appreciated... one more thing, is your kit called AP4600?
can't wait to see them on your car...
silverarrow, thanks, much appreciated... one more thing, is your kit called AP4600?
can't wait to see them on your car...
#24
Registered
iTrader: (25)
holyt sh-t that's a big spacer, don't forget to add that weight on too. That caliper sticks out a mile. The standard RacingBrake BBK caliper only protrudes 1.1" from the rotor face, the Enkei wheel version protrudes about 0.75"
RacingBrake BBK
http://www.racingbrake.com/RX8_s/3254.htm
http://forums.racingbrake.com/viewtopic.php?t=39
http://forums.racingbrake.com/viewtopic.php?t=45
http://forums.racingbrake.com/viewtopic.php?t=64
RacingBrake BBK
http://www.racingbrake.com/RX8_s/3254.htm
http://forums.racingbrake.com/viewtopic.php?t=39
http://forums.racingbrake.com/viewtopic.php?t=45
http://forums.racingbrake.com/viewtopic.php?t=64
#25
stop flooding ur engines
"no. you are not using your for track work..."
when did u get this idea?
i am gonna go BACK to the road course this summer....
tell me more about what i plan to do with my own car........go on
when did u get this idea?
i am gonna go BACK to the road course this summer....
tell me more about what i plan to do with my own car........go on