Lug nut Torquing
#1
8 the HARD way.
Thread Starter
Join Date: Feb 2003
Location: San Antonio
Posts: 1,001
Likes: 0
Received 0 Likes
on
0 Posts
Lug nut Torquing
I read some place that the RX-8 wheels should be torqued to 65-87ft lbs.. then later I read that there was a TSB to torque them to 108 ft lbs.. Is this for all four wheels?
On another note... do you follow the same torquing weight for aftermarket wheels?
On another note... do you follow the same torquing weight for aftermarket wheels?
#8
Registered
Originally Posted by cortc
The proper torque is 85 ft/lbs... 100+ is to much...
Regards,
Gordon
#9
Forum Vendor
Join Date: Nov 2003
Location: south bend, IN
Posts: 136
Likes: 0
Received 0 Likes
on
0 Posts
According to the Mazda tech i spoke with earlier today the correct specified torque as per the Mazda technical information guide manual was 100 ft/lbs. take it or leave, that is straight from Mazda.
#10
I don't care what Mazda says when it comes to this issue... We have a Mazda dealership and I also have spoken to our techs, the service director and a couple of good friends in the automotive engineering field and 100+ is to much... The setting should be 85, so you can take it or leave it...
This 100+ BS is a half-*** attempt by Mazda of NA to fix a problem with a noise coming from the hub assembly during tight cornering due to a tolerance issue... So in order to reduce the likelihood of complaints they issue this TB and absurd torque spec...
Think for yourself and don't believe everything you read...
This 100+ BS is a half-*** attempt by Mazda of NA to fix a problem with a noise coming from the hub assembly during tight cornering due to a tolerance issue... So in order to reduce the likelihood of complaints they issue this TB and absurd torque spec...
Think for yourself and don't believe everything you read...
#11
Bigus Rotus
iTrader: (3)
I see your point, but 85 seems a little soft. I just checked mine and they were at 105. The dealer has been rotating my tires, so I guess they are following the TSB. Is there a reason to have them at 85? Is it better if they have a little room to move if needed? I'm not well versed on lug nuts.
#12
The Turkish Delight
Just make sure they aren't too strong that you can't take them off on the side of the road when you get a flat.
I actually torque mine to about 70. They've been fine.
I actually torque mine to about 70. They've been fine.
#14
8 the HARD way.
Thread Starter
Join Date: Feb 2003
Location: San Antonio
Posts: 1,001
Likes: 0
Received 0 Likes
on
0 Posts
When re-torquing brand new aftermarket wheels (you know after the first couple of miles to let the wheels settle), do you folks jack up the car to do it, or do you just torque it as the cars sits on the wheels..
I'm lazy... what's the right way?
I'm lazy... what's the right way?
#17
Senior Member
Join Date: Jul 2003
Location: DC Metro Area, USA
Posts: 1,554
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by cortc
The initial torque setting should be done with the wheel off the ground.......
rx8cited
#18
GA RX8 Club Member
Join Date: Aug 2004
Location: Cumming GA
Posts: 303
Likes: 0
Received 0 Likes
on
0 Posts
FWIW I had my torque checked at dealer today after doing a caliper paint job and they tightened them to 95 ft#s.
Not sure how far off they were before. Service folks were gone by the time I picked up the car.
Not sure how far off they were before. Service folks were gone by the time I picked up the car.
#20
I am going to rotate my own tires tomorrow and after reading all these posts I am confused as to which torque setting to use. Is there any other info, since the last post was a year ago?
#24
Registered
Join Date: Mar 2005
Location: Rochester Hills, MI
Posts: 301
Likes: 0
Received 0 Likes
on
0 Posts
Pardon me for asking.....but.....what 'problems' would one encounter if a torque spec for lug nuts was not followed??? (besides the obvious if its not too tight it might loosen and the wheel vibrate or fall off)
I'd be very surprised if the majority of folks changing a tire ever used a torque wrench....come to think of it....I've never used one for this purpose either! (shame on me?)
I'd be very surprised if the majority of folks changing a tire ever used a torque wrench....come to think of it....I've never used one for this purpose either! (shame on me?)
#25
The Professor
Originally Posted by apotocki
Pardon me for asking.....but.....what 'problems' would one encounter if a torque spec for lug nuts was not followed??? (besides the obvious if its not too tight it might loosen and the wheel vibrate or fall off)
I'd be very surprised if the majority of folks changing a tire ever used a torque wrench....come to think of it....I've never used one for this purpose either! (shame on me?)
I'd be very surprised if the majority of folks changing a tire ever used a torque wrench....come to think of it....I've never used one for this purpose either! (shame on me?)
So torque wrenches are overwhelmingly in use.
The problem with not using a torque wrench, is that there may be uneven distrobution of pressure holding the wheel on. Imagine if you torqued one really tight and the rest, not so tight. to the wheel, it would be as if you only had that 1 really tight nut holding the entire wheel on. Lots of stress and potential problems...