I'd like to know the above too ^
And also: 17x10 +25 vs 18x9.5 +20 would they give the same flush fit and concavity? |
Wheel Style - RPF-1
Wheel Diameter (Inches) - 18" Wheel Width (Inches) - 9.5F, 9.5R" PCD Bolt Pattern - 5X114.3 Offset - +45mm Want to run 245/40R18s all around. On stock springs/struts on my R3. Will be used for track days only. Should I stick with 245s or put wider in the rear? |
I would stay same front and back for track..you can rotate them that way :)
You can run up to 275-35-18's with no problems on those wheels |
Originally Posted by dannobre
(Post 3624663)
I would stay same front and back for track..you can rotate them that way :)
You can run up to 275-35-18's with no problems on those wheels |
Originally Posted by Munchy
(Post 3624647)
I'd like to know the above too ^
And also: 17x10 +25 vs 18x9.5 +20 would they give the same flush fit and concavity? 9.5+20 and 10+25 are pretty aggressive and will look like crap without being super low with at least -3ish camber. You will be stuck with 225-245 tires and you will have to do some plastic surgery on the inside of the fenders. |
Originally Posted by solareon
(Post 3624674)
is 275 going to be too much tire for the track? and that'll fit up front without rubbing?
If you had done any research at all, you would have found that is the single most common setup on an rx8. No problems with rubbing. |
Originally Posted by j8635621
(Post 3624835)
10+25 and 9.5+20 are basically the same (the 10+25 sticks out like 1mm farther). Concavity depends on the stuff we don't know. Sometimes it is just width related, and other times it is just the same after a certain width. Others have something to do with offset. You have to figure that one out.
9.5+20 and 10+25 are pretty aggressive and will look like crap without being super low with at least -3ish camber. You will be stuck with 225-245 tires and you will have to do some plastic surgery on the inside of the fenders. I`ll prolly be running a stretch too, 205-215 tires. Fender work is understood. Thanks! |
Wheel Style - 5Zigen FN01R-C
Wheel Diameter (Inches) - 18 Wheel Width (Inches) - 9.5 PCD Bolt Pattern - 5X114.3 Offset - 35mm I have no doubt they will fit.. Just wondering what size tire i should look at running with them, and if you would recommend a small spacer for a bit for of an aggressive look. I like it when I can see a little meat outside of the fender wells. |
Okay guys, this is it.
The wheels: 18x9, +41 all around The question: Will I be able to drop the car on Tein S-Techs without any rubbing or fender rolling done? The answer: ??? |
yes
|
I'm getting enkeis ekm3 with this specs:
18x8 +35 offset 245-40-18 I have stock height but planning to lowered, will that fit? Do I need spacer? Thanks |
itll fit fine
|
1 Attachment(s)
uhmmm i wanna get xxr 522 now... i know it's low quality... but i'm broke and jobless... :(... question, what tire size can i put on 18x9.5/+25 that'll fill up my fender gap just fine? and not rolling my fenders as much as possible.. thanks...:worship:...
this is how my car sits right now... and i wanna fill up the gap on the rear using 18x9.5/+25... :)... thanks again... ^^,... Attachment 257388 |
ok so the 17x10 +25 is no where to be found and im dying for wheels
they're receiving 17x10 +12 in next week ANY chance that they'll fit or am i asking for way more trouble than i need (ill be running lightly stretched tires if that matters) |
that is quite a bit of trouble you will definitely be looking at pulling your fenders
wait for the +25 they are concave enough :) |
Pretty sure concavity doesn't matter on the offset with those rims, may be wrong though. +25 will have enough trouble looking good.
|
17x10 +12 will fit with a 245 and lots of camber, rolled/pulled fenders; not worth it IMO
|
dammiittttt
i want my wheels! |
Would a wheel this size fit?
19x9.5 / 5x114.3 / Offset +36 I am on OEM suspension, I'd like to lower it some if possible. What tires would you suggest? |
Originally Posted by jiggawha1
(Post 3636154)
Would a wheel this size fit?
19x9.5 / 5x114.3 / Offset +36 I am on OEM suspension, I'd like to lower it some if possible. What tires would you suggest? width-wise, you could do 255-285 i think. i settled on 275's. i think with 19's though you'll have to go a bit more stretched, like 245 or 255. i don't know though. |
Do 255/35/19, 265/30/19 or 275/30/19. With the 265 or 275 you may need to roll your fenders.
|
Does anyone know of a board user here running this size? Also with running this size, am I harming any suspension components in terms of stress? Would appreciate as much feedback as possible as I found my dream rims for a decent price.
|
your suspension will be fine.
|
Wheel Style - Can't decide
Wheel Diameter (Inches) - 18" Wheel Width (Inches) - 9.5 PCD Bolt Pattern - 5X114.3 Offset - +38 With 265/35s tanabe NF210 springs Flush? |
Tucked. The tires will be close to matching the fender at the correct camber. Won't be hellaflush but still a good look.
|
All times are GMT -5. The time now is 10:16 PM. |
© 2024 MH Sub I, LLC dba Internet Brands