That's what I have in the rear with 245/40 and I still rub with rolled fenders/partially shaved tabs (sometimes). I am gonna try 265/35 next time though after I do some more inner fender work. I'm at a little less than a finger width gapwise and about -2.3ish camber.
|
you rubbing on the inside plastics right?
|
I need to shave the tab down more. Pretty sure anyways. I have driven my car like 30 miles in the past month.
|
So if i'm running normal camber then no rub, right? Wheel talk is so confusing.
|
what suspension? OEM?
j: you're rubbing at the tab?? hmm interesting. |
OEM but i have RB springs to put on, those are mild though
|
It will be past the fenders on RB springs. I'd say don't do it.
Yea I rub on the tab. It was worse before I filed it down a little bit. With the tab gone I'm thinking the wider tires will sit perfect. It will be a while before I change up anything though. School ftl |
So Gram Lights 57D 18x9.5 +22 or +38 Offset?... Definitely need to roll fenders with +22 but what about +38?...Want to go 18x9.5 on all four corners, would there be any problems rubbing on the front fender well when turning? What tire size would you guys recommend? I'm also lowered on Tanabe GF210's.
Has anyone seen both of these offsets of the 57D's, is there any difference in the concavity of the face of the wheel? Thanks |
+22 is gonna seriously limit the width of tire you can run (like a 245/40 or so unless you get a pull or run a good bit of negative camber). +38 will allow a 275/35 with rolled fenders. I have no clue on the concavity.
|
I'm looking at some 18x8's, would I be ok with a 25mm offset or should I go with the 35mm to be safe?
|
what size tire do you want to run?
|
Originally Posted by j8635621
(Post 3691849)
+22 is gonna seriously limit the width of tire you can run (like a 245/40 or so unless you get a pull or run a good bit of negative camber). +38 will allow a 275/35 with rolled fenders. I have no clue on the concavity.
Thanks |
^The rear will rub on the plastic tab covering the screw for the bumper...You'll see.
|
Off-Topic question but I need to know the answer ASAP:
Can XXR 006 Wheels fit on a Corvette? The sizes are 18 x 8.5 front and 18 x 9.5 rear. Offset is +35. The bolt pattern is 5x114.3/5.120. The stock bolt pattern for a Corvette is 5 x 120.7. http://www.discountedwheelwarehouse...._Reference.cfm |
Originally Posted by TopGear8
(Post 3692404)
^The rear will rub on the plastic tab covering the screw for the bumper...You'll see.
|
Front –
18x9 + 20 325/45-18 Rear – 18x10 + 16 235/40-18 On tein s-techs. Rubbing issues? |
you will need a good roll and to grind some of the inside of the fenders down
|
Any way to lessen the rubbing?
|
Yea do what he said lol. Also the 225/45 in the front is too tall. I don't make up hellaflush fitments so you have to figure out the tire that will work
|
hey i can't figure out!!!! this will fit???????
19x8.5 20mm offset front 19x10 20mm offset rear 235/35/19 front 265/30 /19 rear if not what type of tire will work or i need different offset???? |
hmm thats gonna be tough not too sure on fitting 19s compared to 18s
you may be able to get away with just a roll and some camber for the fronts. for the rears you will need a roll, grind tabs way down and possibly a pull for 265s |
can i ask what wheels?
|
sure they are yoshi st-6 stern wheels!!
|
any ideas what i can do???
|
well the specs you posted CAN work but will take a lot of effort on your part to make them fit
a higher 30s/40s offset would be much easer and just need a roll most likely |
All times are GMT -5. The time now is 06:17 AM. |
© 2024 MH Sub I, LLC dba Internet Brands