Yes the wheel studs did extend past the spacer but the pocket in the back of the OEM R3 wheel
was deep enough to allow the extra lenght so everything fit perfect. I used Eibach pro spacer/hub center,and painted them flat back. |
Buying this month!
I'm looking at Enkei RPF1s
9.5x19 w/ 42 offset 265/30 R19 OR 275/30 R19 Fenders are rolled already and I have BC Coils so I just want to know if this will be flush and if it will have issues.. Thanks! |
Smallest offset i can run on koni yellows and tein s-tech with ought any moddifications
|
To give you an Idea.. Im running. 19x9.5 245/35R19 + 12 in the rear and + 22 in the front. Needed to roll my fenders and adj. my camber. I was able to fit 275/30R19 and 285/30R19 that was +35 if I remember in the rears on my last RX8 i did 25535R19 in the front though.. you can probably fit 265/30 in the front im thinking with that offset and width..
|
Originally Posted by Brandonien
(Post 4595000)
I'm looking at Enkei RPF1s
9.5x19 w/ 42 offset 265/30 R19 OR 275/30 R19 Fenders are rolled already and I have BC Coils so I just want to know if this will be flush and if it will have issues.. Thanks! |
sweet, thanks
|
18x8.75 [+33mm] lowered on S-techs on 245/40/18's.
Any problems? Will it look flush? Not looking for a stretched look. |
How about:
245/40/R18's 18 x 9.5" rims, +45 offset 25mm Garageline Spacers 1.4" drop in front 0.7" drop in rear (TEIN S-Tech Springs) |
Originally Posted by OtherSyde
(Post 4600160)
How about:
245/40/R18's 18 x 9.5" rims, +45 offset 25mm Garageline Spacers 1.4" drop in front 0.7" drop in rear (TEIN S-Tech Springs) |
Originally Posted by Mr_Pieper
(Post 4600197)
That's basically what I'm running for a few more days and you will need a good fender roll. The rear bumper tabs will be a small issue as well.
|
If it is close you may be able to get away with bending them upward a bit, but otherwise you will need to break out a cutoff wheel and trim things a bit. That thing is sharp and will noticeably get into your tire.
|
Got question answered.
|
Can anyone help me out.. ive done a bit of research but im still not 100% sure it im going to have fitment issues..
Can I fix 18x10 +15 on a 235/40 tyre? Apparently you can with -1.3 camber but I dont know if I need to roll? Or whats the go if I want to drop it on stance coilovers? |
HELP! Will these wheels fit my rx8?
19"faulken rims with tires
back tires extreme zr, 275/35/zr19. Front 245/35/zr19. Chrome 19" faulken rim with 5 bolt pattern. |
Originally Posted by Mmcogley18
(Post 4604457)
19"faulken rims with tires back tires extreme zr, 275/35/zr19. Front 245/35/zr19. Chrome 19" faulken rim with 5 bolt pattern.
|
Originally Posted by happyisbackk
(Post 4602137)
Can anyone help me out.. ive done a bit of research but im still not 100% sure it im going to have fitment issues.. Can I fix 18x10 +15 on a 235/40 tyre? Apparently you can with -1.3 camber but I dont know if I need to roll? Or whats the go if I want to drop it on stance coilovers?
|
will 18x9.5 +27 with a 255/35/18 tire fit on stock height? I can run some negative camber? And a fender roll? What about a pull? Different tire?
|
Originally Posted by WillPetro
(Post 4604513)
will 18x9.5 +27 with a 255/35/18 tire fit on stock height? I can run some negative camber? And a fender roll? What about a pull? Different tire?
|
I have been looking at a set of Momo Revenge wheels for my 8. They are 18x8, offset is 40. Bolt Pattern is 5x114.3. So looking at the wheel guide it should fit however I've plugged it into 2 different sites and they say it doesn't fit for some reason. I don't know what the center bore is but generally aftermarket wheels have an over sized one with the locking ring ( I think that's what it's called but I can't remember for sure). Does anyone have any ideas?
|
Originally Posted by Mr_Pieper
(Post 4604533)
At stock height that will sit outside of the wheel well and crash into everything as your soft springs let it.
|
Originally Posted by Dustintomi
(Post 4604535)
I have been looking at a set of Momo Revenge wheels for my 8. They are 18x8, offset is 40. Bolt Pattern is 5x114.3. So looking at the wheel guide it should fit however I've plugged it into 2 different sites and they say it doesn't fit for some reason. I don't know what the center bore is but generally aftermarket wheels have an over sized one with the locking ring ( I think that's what it's called but I can't remember for sure). Does anyone have any ideas?
|
Originally Posted by WillPetro
(Post 4604579)
What do you suggest I do? Lower it?
|
Originally Posted by J8635621
(Post 4604581)
Yea. Especially with tires that short. That would look very mexiflush.
|
Originally Posted by WillPetro
(Post 4604584)
So lower it a couple I he's run camber. Roll and pull. Ad maybe new tires?
|
Originally Posted by J8635621
(Post 4604595)
¿Què?
|
All times are GMT -5. The time now is 06:15 AM. |
© 2024 MH Sub I, LLC dba Internet Brands