I apologize that this is a bit off topic but I didn't want to start a new thread.
Tried searching. Since I've now pretty much narrowed down the type and size of wheels/tires (a few posts up ^^^ ), has anyone had any experience specifically dealing with execstudio.com? $1,360 for a full set if I'm doing my math right on their website but I emailed them on Friday and haven't gotten a response yet. I didn't expect to hear from them over the weekend as I assumed they were closed, but I thought I might have heard something by now. If not them, any recommendations? *please delete this post if I have overstepped with this question. Thanks! Justin |
I mistyped I meant 225-5-18 not 245.
|
Originally Posted by mtmetzger
(Post 4767196)
Looking at a set of Work XD9's and I believe the fronts will work. Rears may need some fender roll. Figured I'd post for clarity.
18x9 +38 225/40/18 Nankang 18x10 +38 255/38/18 Nankang Lowered about an inch on unknown springs. |
Will it fit?
pretty set on getting ambit re83 wheels. 18x9.5 +15 5x114.3 front and back. looking to get ksport coilovers when i buy the wheels but i want to make sure they wont rub.:mdrmed:
|
Originally Posted by Lukato
(Post 4768307)
pretty set on getting ambit re83 wheels. 18x9.5 +15 5x114.3 front and back. looking to get ksport coilovers when i buy the wheels but i want to make sure they wont rub.:mdrmed:
|
Originally Posted by dannobre
(Post 4768318)
They will rub. You will have about 3/4 inch to figure out depending on tire size
|
Bigger number than 15. 45 is a common one in rpf1
|
Originally Posted by J8635621
(Post 4768321)
Bigger number than 15. 45 is a common one in rpf1
|
Originally Posted by Lukato
(Post 4768322)
would + 38 be good? or would i still rub
|
Originally Posted by dannobre
(Post 4767230)
Those will be close :) I think the rears should be OK as long as you aren't too low
Originally Posted by delhi
(Post 4767684)
The rear will likely rub if you are loaded at the back. Hit a bump and turning at plaza ramps.
|
Hey all, looking for some quick advice please. Am trying to build a setup for autox and wanted to confirm if my plan will work.
17x8 +30 with 245/45 tires on stock suspension? I think that'll get me pretty close to flush but again, wanted to double check. Will it still clear everything and be ok on the track? |
yup. I run 17x9.5 +38 square on 255/40 tires
I'm pretty low... |
ok, thanks. Kind of new to the whole fitment thing (never had a car without stock wheels) so I wasn't sure. From what I can gather the lip should be in a similar place to a stock wheel with a 30mm spacer, so I found pics of that and figured I'd be good. Ordered the tires tonight, can't wait to hit the track again!
|
1 Attachment(s)
Originally Posted by ZiG
(Post 4769339)
Hey all, looking for some quick advice please. Am trying to build a setup for autox and wanted to confirm if my plan will work.
17x8 +30 with 245/45 tires on stock suspension? I think that'll get me pretty close to flush but again, wanted to double check. Will it still clear everything and be ok on the track? https://cimg1.ibsrv.net/gimg/www.rx8...c3e7554b29.jpg |
^I want that exact setup for my speed6
|
Originally Posted by mtmetzger
(Post 4768352)
Thanks fellas. If I roll the rears a little will I be OK, or do you think it would still rub after a roll?
You can try running more negative camber or something. |
Originally Posted by Lukato
(Post 4768307)
pretty set on getting ambit re83 wheels. 18x9.5 +15 5x114.3 front and back. looking to get ksport coilovers when i buy the wheels but i want to make sure they wont rub.:mdrmed:
|
Disregard my question. There a thread literally right under this one with the answer in the thread title itself. I have even read the damn thread before.
Is there a "dumbass" stamp I can put on my own forehead? Hah.. |
18x9.5 +12 225/45 shit coils, knock off wheels, obviously I went too low in the front, will raise it tomorrow and then go get it aligned, it rubs a little on a lot of things, loving the lack of grip and shitty handling, thanks for having me on the site.
https://cimg8.ibsrv.net/gimg/www.rx8...799ffcd429.jpg https://cimg0.ibsrv.net/gimg/www.rx8...215d08a805.jpg |
The low rider look doesn't work for this car. It seems to make the wheel well look oversized in comparison to the wheels.... which are very pretty btw.
|
It's already back up
|
Also not sure how much I like this front lip either
|
Originally Posted by ZiG
(Post 4769339)
Hey all, looking for some quick advice please. Am trying to build a setup for autox and wanted to confirm if my plan will work.
17x8 +30 with 245/45 tires on stock suspension? I think that'll get me pretty close to flush but again, wanted to double check. Will it still clear everything and be ok on the track? For the record. Installed the above yesterday and am very happy with the fit and look. Can't wait to hit the track again! https://cimg1.ibsrv.net/gimg/www.rx8...7e8616fb74.jpg |
Has anyone tried this?
I was looking for wings/spoilers for my 2004 rx8 and this came up http://www.carid.com/duraflex/gt500-style-wing-trunk-lid-spoiler-mpn-109620.html?gclid=CKCIiOKlnM4CFQGRaQodZuwNkw now I know it's for frs/brz/gt-86 but has anyone tried it or custom mounted this spoiler? I'm curious because why else would it come up under rx8 wings?
|
raised the front, did some more rolling and a small pull in the back, it is no longer rubbing everything, time for an alignment. Some dude came up to me in the parking lot on base, told me he's been watching the car progress and he loves my build....... dude i put coilovers and wheels on it.
https://cimg6.ibsrv.net/gimg/www.rx8...c8bc62de1c.jpg https://cimg8.ibsrv.net/gimg/www.rx8...0eae2fbd0c.jpg |
All times are GMT -5. The time now is 04:17 AM. |
© 2024 MH Sub I, LLC dba Internet Brands