Will It Fit Thread
REW Club
Ok well I’m sure this has been answered before but I have read that this will fit w/o rolling and then I read I will have to roll fenders.
here goes:
Rpf1 18x9.5 +38 or (+45) on Conti extreme contact sports 255/35/18 square.
Lowered on Bilstein b-12 pro kit. So about 1.2” at most in the front. Rear maybe 1”?
i don’t really care about being flush per se as much as having enough contact patch for my build (turbo rew engine).
im not opposed to rolling fenders, but trusting a shop to do it without ruining paint is another story.
Maybe go with 9” rim?
here goes:
Rpf1 18x9.5 +38 or (+45) on Conti extreme contact sports 255/35/18 square.
Lowered on Bilstein b-12 pro kit. So about 1.2” at most in the front. Rear maybe 1”?
i don’t really care about being flush per se as much as having enough contact patch for my build (turbo rew engine).
im not opposed to rolling fenders, but trusting a shop to do it without ruining paint is another story.
Maybe go with 9” rim?
Project Seca
iTrader: (10)
Ok well I’m sure this has been answered before but I have read that this will fit w/o rolling and then I read I will have to roll fenders.
here goes:
Rpf1 18x9.5 +38 or (+45) on Conti extreme contact sports 255/35/18 square.
Lowered on Bilstein b-12 pro kit. So about 1.2” at most in the front. Rear maybe 1”?
i don’t really care about being flush per se as much as having enough contact patch for my build (turbo rew engine).
im not opposed to rolling fenders, but trusting a shop to do it without ruining paint is another story.
Maybe go with 9” rim?
here goes:
Rpf1 18x9.5 +38 or (+45) on Conti extreme contact sports 255/35/18 square.
Lowered on Bilstein b-12 pro kit. So about 1.2” at most in the front. Rear maybe 1”?
i don’t really care about being flush per se as much as having enough contact patch for my build (turbo rew engine).
im not opposed to rolling fenders, but trusting a shop to do it without ruining paint is another story.
Maybe go with 9” rim?
I have some Motegi MR145 Traklite V3's in 18x9.5+35 with 245/40 Federal 595RS-RR's. Measuring my ride height from hub center to highest part of fender arch, I am at 13.5" front and 13.75" rear. I have a VERY light fender roll (no pulling at all) to give myself a little extra clearance from the fenders. Zero rubbing or scrubbing even under load while Autocrossing the car. A 255/35 will give you nearly 9mm more wheel well clearance due to the 255/35 being just under 18mm smaller overall diameter, as a result also make you sit a bit lower (nearly 9mm lower measured ground to chassis) so worth keeping that in mind.
REW Club
https://www.willtheyfit.com/index.php?width=245&aspect=40&diameter=18&wheelwid th=9.5&offset=35&width2=255&aspect2=35&wheel_size= 18&wheel_width=9-5&offset2=38
I have some Motegi MR145 Traklite V3's in 18x9.5+35 with 245/40 Federal 595RS-RR's. Measuring my ride height from hub center to highest part of fender arch, I am at 13.5" front and 13.75" rear. I have a VERY light fender roll (no pulling at all) to give myself a little extra clearance from the fenders. Zero rubbing or scrubbing even under load while Autocrossing the car. A 255/35 will give you nearly 9mm more wheel well clearance due to the 255/35 being just under 18mm smaller overall diameter, as a result also make you sit a bit lower (nearly 9mm lower measured ground to chassis) so worth keeping that in mind.
I have some Motegi MR145 Traklite V3's in 18x9.5+35 with 245/40 Federal 595RS-RR's. Measuring my ride height from hub center to highest part of fender arch, I am at 13.5" front and 13.75" rear. I have a VERY light fender roll (no pulling at all) to give myself a little extra clearance from the fenders. Zero rubbing or scrubbing even under load while Autocrossing the car. A 255/35 will give you nearly 9mm more wheel well clearance due to the 255/35 being just under 18mm smaller overall diameter, as a result also make you sit a bit lower (nearly 9mm lower measured ground to chassis) so worth keeping that in mind.
Thanks Ricky
Last edited by 40th8Jake; 02-16-2021 at 02:30 PM.
The following users liked this post:
Ricky SE3P (02-17-2021)
REW Club
So I plan on running black RPF1s wheels 18/9.5+38 with Achilles ATR sport 2 tire 245/40/18 on stock suspension. I’m worried that the wheel will poke out of the fender!!! I really just want to get the flush look do you think that the wheel will be flush or stick out of the fender and if you have an estimate of how much?
Wheels off a genesis 2019+ wondering if they will fit. Im currently going to have a set of these extra (rip my poor g70)
wonder if they will fit the rx8 which is getting engine rebuild
F: 8Jx19 ET34 225/40ZR19 93Y
R: 8.5Jx19 ET46.5 255/35ZR19 96Y
wonder if they will fit the rx8 which is getting engine rebuild
F: 8Jx19 ET34 225/40ZR19 93Y
R: 8.5Jx19 ET46.5 255/35ZR19 96Y
Project Seca
iTrader: (10)
Yes they will fit with plenty of space still left
No respecter of malarkey
iTrader: (25)
for 9.5” +38 with 265 tires people in the past had to at least roll the lip protrusion flat in the rear, but some tire widths vary
edit: my memory faded a bit, it was 265 size tires and this has been corrected, but some 255 tires may be just as wide. IMO you should plan for rolling the lip flat.
.
edit: my memory faded a bit, it was 265 size tires and this has been corrected, but some 255 tires may be just as wide. IMO you should plan for rolling the lip flat.
.
Last edited by TeamRX8; 03-19-2021 at 06:43 AM.
Went through the 1st 10 pages but lost the will to keep going...so here goes:
Volk Racing TE037 6061 w/ Michelin Pilot Sport 4S
Front: 19x9 +34 255/35R19
Rear: 19x9 +34 255/35R19
Will these fit? I have a feeling it's about borderline from reading others' posts...
Volk Racing TE037 6061 w/ Michelin Pilot Sport 4S
Front: 19x9 +34 255/35R19
Rear: 19x9 +34 255/35R19
Will these fit? I have a feeling it's about borderline from reading others' posts...
Last edited by Staf00; 03-27-2021 at 04:28 PM.
REW Club
for 9.5” +38 with 265 tires people in the past had to at least roll the lip protrusion flat in the rear, but some tire widths vary
edit: my memory faded a bit, it was 265 size tires and this has been corrected, but some 255 tires may be just as wide. IMO you should plan for rolling the lip flat.
.
edit: my memory faded a bit, it was 265 size tires and this has been corrected, but some 255 tires may be just as wide. IMO you should plan for rolling the lip flat.
.
Administrator
iTrader: (7)
when you absolutely need to make these wheels / tires fit...
Advan Model 5: 19x10+42
Falken RT-660's: 275x30x19
Advan Model 5: 19x10+42
Falken RT-660's: 275x30x19
The following users liked this post:
40th8Jake (01-11-2022)
Stock r3 suspension and wheels w spacers?
Running stock suspension and 245/35 tires on the 19 r3 wheels, i can’t find answers that are 100% for this anywhere, can someone tell me for sure if 30mm spacer rear would fit? 25 in the front? I’m playing with anything from 20-25 front to 20-30 in the back,
so many posts say itll Work then I see the opposite and very few mention 30mm at all? Would it work? Will it fit? Will It rub? Will It rub on corners? What would I have to do?
realky don’t wanna order the 25 and 30mm setup to find Im screwed, thanks!!
not sure if this belongs on this thread I couldn’t find any posts about spacers in it, but I don’t see why not the answers for will it fit I couldn’t find anywhere else,
so many posts say itll Work then I see the opposite and very few mention 30mm at all? Would it work? Will it fit? Will It rub? Will It rub on corners? What would I have to do?
realky don’t wanna order the 25 and 30mm setup to find Im screwed, thanks!!
not sure if this belongs on this thread I couldn’t find any posts about spacers in it, but I don’t see why not the answers for will it fit I couldn’t find anywhere else,
Last edited by nick10; 06-11-2021 at 04:56 PM.
Hey guys,
I'm on a good deal for some Enkei's in 18x9.5 +27, do you think it will works with 265/35 like AD08R's ? Or maybe 255/35 ? I know i have to roll fenders but do I need too much camber ? It's not my daily but I want to keep it in track specs so not too low and not abusive camber.
Alternative on these Nt03+M is +40, there is nothing in between and they are more expensive...
I'm on a good deal for some Enkei's in 18x9.5 +27, do you think it will works with 265/35 like AD08R's ? Or maybe 255/35 ? I know i have to roll fenders but do I need too much camber ? It's not my daily but I want to keep it in track specs so not too low and not abusive camber.
Alternative on these Nt03+M is +40, there is nothing in between and they are more expensive...
Hello,
I have a Konig specific question.
I have my eye on Konig Ampliform 18x9.5 +35. Will be running these on 245/40 Pilot Sport 4s.
I can see that Konig offer an A & B variant, with the B variant being more concave and offering less clearance for brake calipers.
I would like to run the B variant on the rear, with the same specs (18x9.5 +35).
Does anyone know if the B variant will cause clearance issues with the rear brake calipers? I can't see the difference in spec anywhere.
Thanks in advance!
I have a Konig specific question.
I have my eye on Konig Ampliform 18x9.5 +35. Will be running these on 245/40 Pilot Sport 4s.
I can see that Konig offer an A & B variant, with the B variant being more concave and offering less clearance for brake calipers.
I would like to run the B variant on the rear, with the same specs (18x9.5 +35).
Does anyone know if the B variant will cause clearance issues with the rear brake calipers? I can't see the difference in spec anywhere.
Thanks in advance!
Nitrous Threadjacker
iTrader: (5)
Looking to check fit on these, from what I've read here I feel pretty good about it but wanted to ask before I **** up.
Konig Hypergram Matte Gray 18x9.5 +35
Falken Ziex ZE960 A/S 245/40R18
Running stock suspension.
Konig Hypergram Matte Gray 18x9.5 +35
Falken Ziex ZE960 A/S 245/40R18
Running stock suspension.
Modulated Moderator
iTrader: (3)
New Member
Are there any specific clearance issues with an R3? Currently all stock, trying to think about 17s or 18s for track wheels/tires, since 19s are absolutely expensive, dont know if the brakes or something else get in the way or with stock bilsteins. Thanks y'all
Noob question
Hi to all im new here so please be gentle... 😅
Im searching if i can fit a set of rims ive found here, but I havent pulled or rolled my fenders and I think its hard for me found anyone can do that here...
Rims specs:
18x8.75 +33
18x8.75 +20
many thanks!!!
Im searching if i can fit a set of rims ive found here, but I havent pulled or rolled my fenders and I think its hard for me found anyone can do that here...
Rims specs:
18x8.75 +33
18x8.75 +20
many thanks!!!
Ty ty don't know how I never got a notification on this.
The only other thing I would ask is should I worry about rubbing.
I'm on Mazdaspeed suspension (Mazdaspeed struts +eibach pro springs) so sits i think like 30mm lower.
Should cause no issues? Or am I removing the already removed fender liner.(Need to get another set of liners eventually cheap set of coil overs caused rubbing and ripping.)
The only other thing I would ask is should I worry about rubbing.
I'm on Mazdaspeed suspension (Mazdaspeed struts +eibach pro springs) so sits i think like 30mm lower.
Should cause no issues? Or am I removing the already removed fender liner.(Need to get another set of liners eventually cheap set of coil overs caused rubbing and ripping.)
Thread
Thread Starter
Forum
Replies
Last Post
warzol
Series I Wheels, Tires, Brakes & Suspension
32
01-27-2020 08:08 PM
iammemares
Series I Wheels, Tires, Brakes & Suspension
15
04-13-2006 01:00 AM
lunatik1
Series I Wheels, Tires, Brakes & Suspension
3
05-04-2005 06:30 PM
JeupRX-8
Series I Wheels, Tires, Brakes & Suspension
5
06-26-2004 10:44 AM