Rew Swap
#1
Rew Swap
Posting details of my rew build finally. Took a year and some months to accomplish due to unforeseen situations, but kept going and now have a "running" rew swap. Last things I need are to finish fitting my A/C compressor, tune, and minor details... oh and smog hehe (thanks Cali)
The Build:
Street ported rew
Rx8 performance oil pan
Garret t4 70mm 96 ar
Xcessive lim ported
Cosmo uim
T4 twin scroll manifold
X2 turbosmart comp gate 40
FFE 6 injector fuel rails
X4 1000cc injector dynamic secondary
X2 850cc injector dynamic primary
Greddy type fv bov
Rx8 throttle body
Aero motive 340 lph in tank
Adaptronic pnp
Act 6 plate clutch
Rx8 omp
Bhr ignition
Rx8 alternator
Rx8 trigger wheel (rx8 front plate)
6 speed rx8 trans
Rx8 harness
034 Motorsports surge (044 Bosch pump)
8an feed line
6an return
Rx8 performance oil coolers
specials thanks to Tito at Renown for the fab work and Maxime for the base tune. The car is yet to be fully tested, but for now I can at least move it around parking spots lol
Instagram: chill_will_ib
The Build:
Street ported rew
Rx8 performance oil pan
Garret t4 70mm 96 ar
Xcessive lim ported
Cosmo uim
T4 twin scroll manifold
X2 turbosmart comp gate 40
FFE 6 injector fuel rails
X4 1000cc injector dynamic secondary
X2 850cc injector dynamic primary
Greddy type fv bov
Rx8 throttle body
Aero motive 340 lph in tank
Adaptronic pnp
Act 6 plate clutch
Rx8 omp
Bhr ignition
Rx8 alternator
Rx8 trigger wheel (rx8 front plate)
6 speed rx8 trans
Rx8 harness
034 Motorsports surge (044 Bosch pump)
8an feed line
6an return
Rx8 performance oil coolers
specials thanks to Tito at Renown for the fab work and Maxime for the base tune. The car is yet to be fully tested, but for now I can at least move it around parking spots lol
Instagram: chill_will_ib
Last edited by WillIbarrola; 08-14-2017 at 01:20 PM.
The following users liked this post:
comebackqid (08-15-2017)
The following users liked this post:
WillIbarrola (08-14-2017)
#3
Registered
Sweet, welcome to the club.
The following users liked this post:
WillIbarrola (08-14-2017)
#6
FULLY SEMI AUTOMATIC
iTrader: (9)
im curious if you did some or all of the work yourself minus the fab work and apx. cost thus far
#7
The only things I had not done myself was the engine rebuild and fabrication. As far as wiring, running fuel lines, and throwing the motor in and all together I was able to do. Total cost was around 12k I want to say. I stopped keeping track after a couple grand lol.
#8
FULLY SEMI AUTOMATIC
iTrader: (9)
just curious. a buddy of mine recently had his motor rebuilt (pettit s/c) but asked a local shop about rew swap prices. iirc they sair ~15k for a turn key job
#9
Registered
#10
Hey guys just posting a little update! A couple weeks ago I was able to get the car street tuned. Our first go at tuning was a complete fail because one of my wg flanges was warped and leaking. After getting the leak fixed and putting in 11 psi springs car felt way better. A week or two after that I was given the opportunity to track the car at streets of willow thanks to Superstreet! Car still needs more tuning at the top end, hopefully soon.
Enjoy the vid!
Enjoy the vid!
Last edited by WillIbarrola; 10-24-2017 at 10:33 PM.
#11
Registered
I have a great question for you since you have Adaptronics. In triggering, what do your ignition offset angles look like?? Example - 41, 31, 21, 11 or 38, 28, 18, 8, etc... I have asked a ton of people and nobody seems to respond.
#13
Registered
I sent him an email about 2 weeks ago with my logs and my tune. He said he would get back with me about the timing/triggering, but I haven't heard anything back. If I could just get a few people with REW motors with REW triggers/wheels confirm their trigger angles ( I would assume they should be all close), it would make me feel much more comfortable with my timing map. I know i'm close, but even 5-10 degrees either way can cause big problems.
#17
Stroker, in all honesty im not sure how to check this I left the tuner to the more capable hand. If you'd to inform me how I can try to get you the info.
also managed to make it out to seven stock this year. Car ran decently.. just had one incident where I had to push start it at a gas station.
also managed to make it out to seven stock this year. Car ran decently.. just had one incident where I had to push start it at a gas station.
#18
hey guys just looking for some input. Tried getting my car tuned. At wide open throttle my car would break up at 5500 rpm. Along with that my adaptronic ecu won't update. So far I've been told I have a bad ecu now. wondering if anything else would cause this since my daptronic did fine when I had a greddy turbo on my renesis.. thanks in advance
#22
Registered
I had ignition breakup/spark blowout problems above 5 psi for a bit, and what solved it for me was switching to an Autolite 3933 plug. They are gapable and only $2.99 each ($15/set shipped on ebay). I change them every few thousand miles because they are soo cheap. I was able to close the gap down to 0.025-0.028", and I haven't had any issues since. Ran those cheap plugs up to 20 psi. I also have D585 coils with dwell set to 4,500.
The NGK plugs i swapped out only had a few hundred miles on them.... Could be just some fouled plugs...
The NGK plugs i swapped out only had a few hundred miles on them.... Could be just some fouled plugs...